HeathCo WLTRX5892 Users Manual

Model #DFI-5892-WH

USE AND CARE GUIDE

VIDEO MOTION SECURITY LIGHT

Item #1001814036

Questions, problems, missing parts?

Before returning to the store, call Deant Customer Service

8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday

1-866-308-3976

HOMEDEPOT.COM

We appreciate the trust and condence you have placed in Deant through the purchase of this video motion

security light. We strive to continually create quality products designed to enhance your home. Visit us online to see

our full line of products available for your home improvement needs. Thank you for choosing Deant!

THANK YOU

Table of Contents

Table of Contents ......................................2

Safety Information ....................................2

Warranty ...................................................3

5-Year Limited Warranty ........................3

Pre-Installation .........................................3

Planning Installation ..............................3

Specications ........................................3

Safety Information

PRECAUTIONS

Ƒ Please read and understand this entire manual

before attempting to assemble, install, or operate
this light xture.

Ƒ This light xture requires a 120-Volt AC power

source.

Ƒ Some codes require installation by a qualied

electrician.

Ƒ This light xture must be properly grounded.

Ƒ This light xture should be installed outdoors to a

wall or eave.

Ƒ The light xture should be mounted approximately

8 ft. (2.4 m) above the ground. If the light xture
is mounted higher than recommended, aiming the
sensor down will reduce the coverage area.

Ƒ The light xture/camera requires constant power

to operate. Whenever the power is turned on to
the light xture (either for the rst time or after
a power outage), the light requires a 60-second
boot-up period before the camera will be fully
operational.

Ƒ Many states regulate the use of security cameras

and other recording devices. It is the purchaser’s
sole responsibility to ensure compliance with all
applicable laws and to provide any legally required
notices. Check local laws regarding the use of any
recording devices and cameras prior to installation.

Tools Required .......................................4

Hardware Included .................................5

Package Contents ..................................5

Installation ................................................6

Operation...................................................8

Care and Cleaning ..................................12

Troubleshooting ......................................13

WARNING: Turn the power off at the circuit breaker or
fuse. Place tape over the circuit breaker switch and verify
power is off at the light xture.

WARNING: Risk of re. Keep the lamp heads at least
2in. (51mm) from combustible materials.

CAUTION: Burn hazard. Allow the light xture to cool
before touching.

NOTICE: Do not connect this light xture to a dimmer switch or
timer.

Ƒ This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.

Ƒ This device complies with Industry Canada licence-

exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not
cause interference, and (2) this device must accept
any interference, including interference that may
cause undesired operation of the device.

Ƒ CAN ICES-3 (B)/NMB-3(B)

2

Warranty

5-YEAR LIMITED WARRANTY

WHAT IS COVERED

This product is guaranteed to be free of factory defective parts and workmanship for a period of 5 years from date
of purchase. Purchase receipt is required for all warranty claims.

WHAT IS NOT COVERED

This guarantee does not include repair service, adjustment and calibration due to misuse, abuse or negligence, or
LEDs. Unauthorized service or modication of the product or of any furnished component will void this warranty in
its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use,
unauthorized service, or return shipping charges. This warranty is not extended to other equipment and components
that a customer uses in conjunction with this product.

No service parts available for this product.

Contact the Customer Service Team at 1-866-308-3976 or visit www.homedepot.com.

Pre-Installation

PLANNING INSTALLATION

Before installing the light xture, ensure that all parts are present. Compare parts with the Hardware Included and
Package Contents sections. If any part is missing or damaged, do not attempt to assemble, install, or operate this

light xture.

Estimated installation time: 30 minutes

SPECIFICATIONS

Range

PIR motion sensing angle

Electrical load - LED

Lumens

Power requirements

Video resolution

Video frame rate

Video viewing angle

Operating temperature

Mobile device requirements

Up to 70 ft. (21.3 m) (Varies with surrounding temperature)

Up to 180°

34 Watts

2350

120 VAC, 60 Hz

Hi: 1280 x 720 (720p), Med: 640 x 360, Low: 320 x 180

Adjustable up to 25 fps (Default - 15 fps)

Up to 100°

-13°F to +120°F (-25°C to +50°C)

iPhone and Android compatible. See Homedepot.com for system
requirements.

3 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Pre-Installation (continued)

TOOLS REQUIRED

Phillips
screwdriver

Circuit tester Work gloves

Ladder Safety goggles Mobile Device

1/8 in. Flathead
screwdriver

Wire strippers/
cutters

Silicone
sealant

4

Pre-Installation (continued)

HARDWARE INCLUDED

NOTE: Hardware shown to actual size.

AA BB CC

DD

EE

FRONT

Part Description Quantity

AA Rubber plug 1

BB Mounting bracket screw 2

CC Mounting bracket screw 2

DD Large mounting bolt 1

EE Small mounting bolt (pre-installed) 1

FF Mounting bracket (not to scale) 1

GG Mini screwdriver 1

FF GG

PACKAGE CONTENTS

A

D

E

Part Description Quantity

A Lamp head 2

B Light xture 1

C Motion sensor 1

D Mounting plate 1

E Camera 1

B

C

5 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Installation

FRONT

Determining the mounting

1

location

NOTE: The light xture should be mounted approximately
8 ft. (2.4 m) above the ground. If the light xture is
mounted higher than recommended, aiming the sensor
down will reduce the coverage area.

Ƒ Determine the mounting location – wall or eave

mount.

Ƒ Position the lamp heads (A) in the general

direction of the desired light coverage.

Ƒ If needed, rotate the motion sensor (C) so the

text faces upward.

Wall Mount

A

THIS SIDE UP

180°

Eave Mount

C

Removing the mounting plate

2

NOTE: This xture comes with a mounting plate (D). It is
pre-assembled on the light xture (B) for shipping.

NOTE: The small mounting bolt (EE) is pre-installed in
the light xture (B). Do not attempt to remove the small
mounting bolt (EE).

Ƒ Unscrew the small mounting bolt (EE) connecting

the light xture (B) to the mounting plate (D) and
remove the mounting plate (D).

D

B

EE

Installing the mounting bracket

3

WARNING: Turn the power off at the circuit breaker or
fuse. Place tape over the circuit breaker switch and verify
power is off at the light xture.

NOTE: Six mounting bracket screws of various sizes are
included. The installation will only require two. Discard the
unused mounting bracket screws after installation.

Ƒ Remove the existing light xture.
Ƒ Install the mounting bracket (FF) with the

stamped word “FRONT” facing away from the
junction box. Use the mounting bracket screws
(BB or CC) that best t the junction box.

Ƒ Firmly pull on the mounting bracket to verify

it is securely mounted to the junction box. If
necessary, use the screws that were removed
from the existing light xture.

T

FRON

BB or CC

FF

6

Installation (continued)

UP/Haut/Arriba

Installing the mounting plate

4

Ƒ Route the junction box wires through the hole

in the mounting plate (D).

Ƒ Place the mounting plate (D) against the

junction box.

Ƒ When mounting to a wall, the “UP” arrow

must point upward.

Ƒ When mounting to an eave, the “UP” arrow

must point toward the building.

Ƒ Insert the large mounting bolt (DD) through

the mounting plate (D) hole located below the
threaded hole, and thread it into the center
hole of the mounting bracket (FF). Tighten the
bolt (DD) securely.

Ƒ Firmly pull on the mounting plate (D) to

verify it is securely attached to the mounting
bracket(FF).

U

P

/Hau

t

/Arri

b

a

GND
Terre
T

ie

rra

N

(Whit

B

la

e

n

/

c/Blanc

o

)

L

(Black

No

i

/

r/

N

e

g

ro

)

Making the electrical

5

connections

Ƒ Insert the junction box wires into the side of

the terminal block and around the ground
screw. Tighten terminal block screws using
the mini-screwdriver (GG) and ground screw to
secure the wires.

Ƒ Insert the white wire from the junction box

into the terminal marked “N (White)”.

Ƒ Insert the black wire from the junction box

into the terminal marked “L (Black)”.

Ƒ Connect the bare or green ground wire

from the junction box to the ground screw
(marked with “GND”).

UP/Haut/Arriba

GND
Terre
Tierra

N (White/
Blanc/Blanco)

L (Black/
Noir/Negro)

FF

ONT

FR

D

D

DD

Mounting the light fixture

6

D

B

NOTICE: The two pins on the rear of the light xture must be
inserted into the terminal block for the light to work.

Ƒ Align the bottom edge of the light xture (B) with

the bottom edge of the mounting plate(D). Tilt
the light xture (B) toward the mounting plate (D),
making sure the light xture (B) is centered on
the mounting plate (D).

Ƒ Tighten the small mounting bolt (EE) securely

through the center of the mounting plate(D). Do
not overtighten.

Ƒ Push the rubber plug (AA) rmly into the

mounting bolt hole on the light xture (B).

7 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

AA

EE

Installation (continued)

Caulking around the light

7

fixture

Ƒ Caulk around the mounting plate (D) and

mounting surface with silicone sealant (not
included).

Operation

D

Adjusting the lamp heads

1

WARNING: Risk of re. Keep the lamp heads at least
2in. (51mm) from combustible materials.

CAUTION: Keep lamp heads 30° below horizontal to
avoid water damage and electrical shock.

Ƒ Turn the power on at the circuit breaker or fuse

and turn on the wall switch.

Ƒ If needed, gently grasp the lamp heads (A) and

tilt them up or down or side to side to adjust
the light coverage area.

A

THIS SIDE UP

180°

Rotating the sensor controls

2

downward

Ƒ Rotate the motion sensor (C) so the text faces

upward.

THIS SIDE UP

180°

C

8

Operation (continued)

Downloading the mobile app

3

Ƒ Download the Noti™ mobile app. Search for

the “Noti Video Solutions” app.

Ƒ iOS Devices – Download the app from the

App StoreSM.

Ƒ Android Devices – Download the app from

the Google Play™ store.

Viewing live video

5

The Noti app provides live-stream video from the
camera to a mobile device.

Ƒ Tap the name of the camera to be viewed.
Ƒ While in the live-stream screen, the following

options are available:

Ƒ Tap the video camera icon ( ) to start

recording live video. Tap again to stop
recording.

Ƒ Tap the camera icon (

image from the live-stream video.

Ƒ To return to the main app screen, tap the (

or “Back” button in the top left corner.

NOTE: All videos and images will be saved to the mobile
device currently being used to view the live-stream video.

) to save a still

Connecting the light to the

4

mobile app

NOTICE: The network password will be required to complete this
process.

Ƒ Ensure the power to the light is turned ON.

Allow 60 seconds for system boot-up.

Ƒ On the mobile device, go to Settings > Wi-Fi

and select “Noti_Video_SecurityXXXX”
(“XXXX” represents the unique MAC address
of each light xture) from the available Wi-Fi
networks.

Ƒ Once connected, open the Noti app. The app

will detect the new light.

Ƒ Select “Yes” to start the setup and the app will

guide you through the remaining steps.

NOTE: When creating a new Noti account, the username
and password must be a minimum of 4 characters and a
maximum of 12 characters. Alpha-numeric and/or special
characters may be used.

Understanding the motion

6

detection process

This light has dual motion detection technologies.

Ƒ The light is controlled by a 180° PIR (passive

infra-red) sensor. This sensor detects a
temperature difference moving in front of it.
When motion is detected after dark, the light will
come on at the selected “Full Bright Intensity”
level.

Ƒ The camera uses both the 180° PIR sensor as

well as a 100° image sensor located within the
camera software. The camera’s image sensor
will not activate unless the PIR sensor rst

)

detects a moving temperature difference within
the detection zone. The camera will record
motion day or night.

9 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Operation (continued)

Using the event list

7

Tap the Events tab.

An event is created each time the camera senses
motion.

Ƒ Basic Service – The event list will show the date

and time the motion was detected.

Ƒ Premium Service (available for an additional

fee) – The event list will include the date, time,
and video of the event each time motion was
detected. The video of each event will also be
available to download for 30 days.

Adjusting the light settings

9

The light settings allow you to adjust the full bright
duration, the DualBrite® duration, and the percentages
of light intensity.

NOTE: Changes made to one light’s settings will not
affect another light’s settings.

Tap > Feature Settings > Light to select the light
settings.

Ƒ Full Bright Duration – This adjusts the amount

of time the light will stay ON after all motion has
stopped.

Ƒ DualBrite Duration – This adjusts the amount of

time the light stays ON at a reduced brightness
level when no motion is detected.

Ƒ Full Bright Intensity – This adjusts the intensity

level of the light when motion is detected.

Ƒ DualBrite Dimming Level – This adjusts the

intensity level of the light when no motion is
detected.

Receiving notifications

8

Tap > Feature Settings > Notications to select the
notication settings.

If notications are turned on, an email and/or push
notication is sent each time the camera senses
motion. Tap on the notication to be taken to the live­view video screen (Basic service) or the Event video
(Premium service).

Adjusting the camera

10

The camera settings allow you to adjust the motion
detection sensitivity, motion detection zones, and
video quality.

Tap > Feature Settings > Camera to select the
camera settings.

settings

NOTE: Changes made to one camera’s settings will not
affect another camera’s settings.

NOTE: The higher the “Sensitivity” setting, the greater the
possibility of false triggering. To reduce false triggering,
select a lower setting.

Ƒ Motion Detection – This adjusts the camera’s

sensitivity to motion in its eld of view.

Ƒ Motion Detection Zones – This adjusts the

camera’s detection area to include or exclude
zones in its eld of view.

Ƒ Auto Adjust – Disabling this setting allows

manual adjustments of the video’s quality
settings. For best performance, leave the Auto
Adjust ON.

10

Operation (continued)

Setting the sensor for testing

11

NOTE: The light xture will operate during the day or
night during testing. The light will stay on for 5 seconds
after all motion is stopped.

NOTE: The light requires a 60-second boot-up period
before the camera will be fully operational.

Tap > Feature Settings > Camera > Motion
Detection to select the motion detection settings.

The light xture will automatically enter “Test” mode
whenever the “Motion Detection” option is selected.
The light xture will remain in “Test” until one of the
following actions occurs:

Ƒ The “Save” or “Cancel” option is selected.

Ƒ No movement during the testing process for 30

seconds.

Ƒ Three minutes have passed without changing

one of the on-screen settings.

Adjusting the motion sensor

12

detection zone

NOTE: The camera’s (E) detection zone is inside of the
light’s detection zone. When the motion sensor (C) for the
light is adjusted, the camera’s (E) motion sensor will also
be adjusted.

If motion is detected outside the camera’s detection zone,
the light may turn on but the camera will not record an
event.

Ƒ Perform a “walk test”: walk in an arc across

the front of the motion sensor (C).

Ƒ Watch the light. The light will come on and the

red LED will ash indicating motion has been
detected.

Ƒ Stop, wait for the light to turn off, and then

begin walking again.

Ƒ Continue this process until the detection zone

has been established.

Ƒ If needed, gently grasp the motion sensor (C)

and move it from side to side or up and down
to adjust the detection zone.

Ƒ Adjust the “Motion Detection” sensitivity to

High, Medium, or Low as needed.

NOTE: The motion sensor (C) is more sensitive to motion
moving across the front of the sensor. The motion sensor
(C) is less sensitive to motion moving directly toward the
front of the sensor.

E

C

C and E

11 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Operation (continued)

13

15

Adding multiple users

The Noti system allows control of multiple users
within an account.

Tap > Advanced Settings > Manage Multiple Users.

Ƒ Tap the “Add Viewers” button and type the

email address in the “To:” eld.

Ƒ Tap the “Send” button.

NOTE: When adding multiple users, separate the email
addresses with a semicolon.

Using manual mode

Manual mode overrides the motion sensor (C) and will
turn the light on at the preset
level

. This feature works day or night. The motion sensor

(C) will reset to motion sensing mode at sunrise.

Ƒ On the main screen under the “Systems” tab,

choose “ON”, “OFF”, or “AUTO” to control the
lights for the selected Noti system.

“Full Bright Intensity”

Care and Cleaning

Adding system name and

14

Add a name and photo to represent the Noti system
on the mobile device. The photo will be placed inside
the blue circle icon next to the selected Noti system.

Tap > Advanced Settings > System Name/Photo.

16

To delete a Noti system from an account:

photo

Ƒ Enter a name for the Noti system.
Ƒ Select an existing photo and take a new photo

to represent the Noti system.

NOTE: The light settings and name are stored in the light
xture. The photo is locally stored on the mobile device and
is only visible on that device.

Deleting a Notifi system

Ƒ Turn off the wall switch controlling the Noti

system.

Ƒ On the main “Systems” screen, wait for the

system to go ofine (the system name and
image will turn gray).

Ƒ Once ofine, swipe the Noti system to be

deleted to the left and tap the trashcan icon
( ).

Ƒ To prolong the original appearance, clean the light xture with clear water and a soft, damp cloth only.

Ƒ Do not use paints, solvents, or other chemicals on this light xture. They could cause a premature

deterioration of the nish. This is not a defect in the nish and will not be covered by the warranty.

Ƒ Do not spray the light xture with a hose or power washer.

Ƒ To clean the camera lens, use a dry, microber cloth only.

12

Troubleshooting

Problem Possible Cause Solution

The light will not come on. Ƒ The light switch is turned off. Ƒ Turn the light switch on.

The light comes on during
the day.

The light comes on for no
apparent reason.

The lights stay ON too late
in the “DualBrite Duration”
setting.

The lights do not stay ON
late enough in the “DualBrite
Duration” setting.

Ƒ The fuse is blown or the circuit

breaker is turned off.

Ƒ The light is not scheduled to come

ON.

Ƒ The circuit wiring is incorrect (if this

is a new installation).

Ƒ The motion sensor is aimed in the

wrong direction.

Ƒ The outside air temperature is close

to the same as a person’s body
heat.

Ƒ The light is scheduled to come ON. Ƒ Adjust the scheduled light

Ƒ The motion sensor may be sensing

small animals or automobile trafc.

Ƒ The “Motion Detection” setting is

set too high.

Ƒ The “DualBrite Duration” is

operating at the preset “DualBrite
Dimming Level” setting.

Ƒ The outside temperature is much

warmer or cooler than a person’s
body heat (summer or winter).

Ƒ The light xture is wired through a

dimmer or timer.

Ƒ The “DualBrite Duration” OFF time is

set to late.

Ƒ The “DualBrite Duration” OFF time is

set to early.

Ƒ Replace the fuse or turn the

circuit breaker on.

Ƒ Recheck the light operation

during the scheduled “DualBrite
Duration” (after sunset).

Ƒ Verify the wiring is correct.

Ƒ Re-aim the motion sensor to

cover the desired area.

Ƒ Increase the “Motion Detection”

setting.

operation in “DualBrite
Duration.”

Ƒ Decrease the “Motion Detection”

setting or reposition the motion
sensor.

Ƒ Decrease the “Motion Detection”

setting.

Ƒ The light xture is operating

normally under these
circumstances. The “DualBrite
Duration” time is adjustable.

Ƒ Decrease the “Motion Detection”

setting.

Ƒ Do not use a dimmer or timer to

control the light xture. Replace
the dimmer or timer with a
standard on/off wall switch.

Ƒ Adjust the “DualBrite Duration”

OFF time to the desired setting.

Ƒ Adjust the “DualBrite Duration”

OFF time to the desired setting.

13 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Troubleshooting (continued)

Problem Possible Cause Solution

The lights stay on
continuously.

The lights ash on and off. Ƒ Heat or light from the lamp heads

The light xture is not
responding to the app.

The app is not nding the light
xture.

Motion notications are not
being sent to the app.

Ƒ The motion sensor may be picking

up a heat source, such as an air
vent, dryer vent, or brightly painted,
heat-reective surface.

Ƒ The motion sensor is in manual

mode.

Ƒ The light xture is wired through a

dimmer or timer.

Ƒ The light xture is on the same

circuit as a motor, transformer, or
uorescent bulb.

may be turning the motion sensor
on and off.

Ƒ Heat is being reected from other

objects and may be turning the
motion sensor on and off.

Ƒ The light is ofine (the system name

and image are gray).

Ƒ The light is unable to connect to the

wi- (the system name and image
are gray).

Ƒ The light may have been deleted

from the account.

Ƒ Notications are turned off in the

app.

Ƒ Motion is not being detected inside

the camera’s detection zone.

Ƒ Decrease the “Motion Detection”

setting or reposition the motion
sensor.

Ƒ Turn the manual mode option to

Off or Auto. See Using manual
mode on page 12.

Ƒ Do not use a dimmer or timer to

control the light xture. Replace
the dimmer or timer with a
standard on/off wall switch.

Ƒ Install the light xture on

a circuit without motors,
transformers, or uorescent
bulbs.

Ƒ Reposition the lamp heads away

from the motion sensor.

Ƒ Decrease the “Motion Detection”

setting or reposition the motion
sensor.

Ƒ Ensure the light has power.

Ƒ Ensure the light is connected to

the wi- router.

Ƒ Turn the power to the light off.

Wait 30 seconds and turn the
power on. Wait 60 seconds for
the light to boot-up.

Ƒ Reconnect the light to the app

(see step 4, page 9).

Ƒ Turn notications on in the app

(see step 8, page 10).

Ƒ Re-aim the motion sensor

to cover the desired area or
increase the “Motion Detection”
setting.

14

Questions, problems, missing parts?

Before returning to the store, call Deant Customer Service

8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday

1-866-308-3976

HOMEDEPOT.COM

Retain this manual for future use.

Apple and the Apple logos are trademarks of Apple Inc., registered in the U.S., and other countries. App Store is a

Wi-Fi® is a registered trademark of Wi-Fi Alliance

service mark of Apple Inc.

Google Play is a trademark of Google Inc.

Android is a trademark of Google Inc.

Model #DFI-5892-WH

USE AND CARE GUIDE

VIDEO MOTION SECURITY LIGHT

Item #1001814036

Questions, problems, missing parts?

Before returning to the store, call Deant Customer Service

8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday

1-866-308-3976

HOMEDEPOT.COM

We appreciate the trust and condence you have placed in Deant through the purchase of this video motion

security light. We strive to continually create quality products designed to enhance your home. Visit us online to see

our full line of products available for your home improvement needs. Thank you for choosing Deant!

THANK YOU

Table of Contents

Table of Contents ......................................2

Safety Information ....................................2

Warranty ...................................................3

5-Year Limited Warranty ........................3

Pre-Installation .........................................3

Planning Installation ..............................3

Specications ........................................3

Safety Information

PRECAUTIONS

Ƒ Please read and understand this entire manual

before attempting to assemble, install, or operate
this light xture.

Ƒ This light xture requires a 120-Volt AC power

source.

Ƒ Some codes require installation by a qualied

electrician.

Ƒ This light xture must be properly grounded.

Ƒ This light xture should be installed outdoors to a

wall or eave.

Ƒ The light xture should be mounted approximately

8 ft. (2.4 m) above the ground. If the light xture
is mounted higher than recommended, aiming the
sensor down will reduce the coverage area.

Ƒ The light xture/camera requires constant power

to operate. Whenever the power is turned on to
the light xture (either for the rst time or after
a power outage), the light requires a 60-second
boot-up period before the camera will be fully
operational.

Ƒ Many states regulate the use of security cameras

and other recording devices. It is the purchaser’s
sole responsibility to ensure compliance with all
applicable laws and to provide any legally required
notices. Check local laws regarding the use of any
recording devices and cameras prior to installation.

Tools Required .......................................4

Hardware Included .................................5

Package Contents ..................................5

Installation ................................................6

Operation...................................................8

Care and Cleaning ..................................12

Troubleshooting ......................................13

WARNING: Turn the power off at the circuit breaker or
fuse. Place tape over the circuit breaker switch and verify
power is off at the light xture.

WARNING: Risk of re. Keep the lamp heads at least
2in. (51mm) from combustible materials.

CAUTION: Burn hazard. Allow the light xture to cool
before touching.

NOTICE: Do not connect this light xture to a dimmer switch or
timer.

Ƒ This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.

Ƒ Le présent appareil est conforme aux CNR

d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée
aux deux conditions suivantes : (1) l’appareil ne
doit pas produire de brouillage, et (2) l’utilisateur
de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.

Ƒ CAN ICES-3 (B)/NMB-3(B)

17 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Warranty

5-YEAR LIMITED WARRANTY

WHAT IS COVERED

This product is guaranteed to be free of factory defective parts and workmanship for a period of 5 years from date
of purchase. Purchase receipt is required for all warranty claims.

WHAT IS NOT COVERED

This guarantee does not include repair service, adjustment and calibration due to misuse, abuse or negligence, or
LEDs. Unauthorized service or modication of the product or of any furnished component will void this warranty in
its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use,
unauthorized service, or return shipping charges. This warranty is not extended to other equipment and components
that a customer uses in conjunction with this product.

No service parts available for this product.

Contact the Customer Service Team at 1-866-308-3976 or visit www.homedepot.com.

Pre-Installation

PLANNING INSTALLATION

Before installing the light xture, ensure that all parts are present. Compare parts with the Hardware Included and
Package Contents sections. If any part is missing or damaged, do not attempt to assemble, install, or operate this

light xture.

Estimated installation time: 30 minutes

SPECIFICATIONS

Range

PIR motion sensing angle

Electrical load - LED

Lumens

Power requirements

Video resolution

Video frame rate

Video viewing angle

Operating temperature

Mobile device requirements

Up to 70 ft. (21.3 m) (Varies with surrounding temperature)

Up to 180°

34 Watts

2350

120 VAC, 60 Hz

Hi: 1280 x 720 (720p), Med: 640 x 360, Low: 320 x 180

Adjustable up to 25 fps (Default - 15 fps)

Up to 100°

-13°F to +120°F (-25°C to +50°C)

iPhone and Android compatible. See Homedepot.com for system
requirements.

18

Pre-Installation (continued)

TOOLS REQUIRED

Phillips
screwdriver

Circuit tester Work gloves

Ladder Safety goggles Mobile Device

1/8 in. Flathead
screwdriver

Wire strippers/
cutters

Silicone
sealant

19 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Pre-Installation (continued)

HARDWARE INCLUDED

NOTE: Hardware shown to actual size.

AA BB CC

DD

EE

FRONT

Part Description Quantity

AA Rubber plug 1

BB Mounting bracket screw 2

CC Mounting bracket screw 2

DD Large mounting bolt 1

EE Small mounting bolt (pre-installed) 1

FF Mounting bracket (not to scale) 1

GG Mini screwdriver 1

FF GG

PACKAGE CONTENTS

A

D

E

Part Description Quantity

A Lamp head 2

B Light xture 1

C Motion sensor 1

D Mounting plate 1

E Camera 1

B

C

20

Installation

FRONT

Determining the mounting

1

location

NOTE: The light xture should be mounted approximately
8 ft. (2.4 m) above the ground. If the light xture is
mounted higher than recommended, aiming the sensor
down will reduce the coverage area.

Ƒ Determine the mounting location – wall or eave

mount.

Ƒ Position the lamp heads (A) in the general

direction of the desired light coverage.

Ƒ If needed, rotate the motion sensor (C) so the

text faces upward.

Wall Mount

A

THIS SIDE UP

180°

Eave Mount

C

Removing the mounting plate

2

NOTE: This xture comes with a mounting plate (D). It is
pre-assembled on the light xture (B) for shipping.

NOTE: The small mounting bolt (EE) is pre-installed in
the light xture (B). Do not attempt to remove the small
mounting bolt (EE).

Ƒ Unscrew the small mounting bolt (EE) connecting

the light xture (B) to the mounting plate (D) and
remove the mounting plate (D).

D

B

EE

Installing the mounting bracket

3

WARNING: Turn the power off at the circuit breaker or
fuse. Place tape over the circuit breaker switch and verify
power is off at the light xture.

NOTE: Six mounting bracket screws of various sizes are
included. The installation will only require two. Discard the
unused mounting bracket screws after installation.

Ƒ Remove the existing light xture.
Ƒ Install the mounting bracket (FF) with the

stamped word “FRONT” facing away from the
junction box. Use the mounting bracket screws
(BB or CC) that best t the junction box.

Ƒ Firmly pull on the mounting bracket to verify

it is securely mounted to the junction box. If
necessary, use the screws that were removed
from the existing light xture.

T

FRON

BB or CC

FF

21 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Installation (continued)

UP/Haut/Arriba

Installing the mounting plate

4

Ƒ Route the junction box wires through the hole

in the mounting plate (D).

Ƒ Place the mounting plate (D) against the

junction box.

Ƒ When mounting to a wall, the “UP” arrow

must point upward.

Ƒ When mounting to an eave, the “UP” arrow

must point toward the building.

Ƒ Insert the large mounting bolt (DD) through

the mounting plate (D) hole located below the
threaded hole, and thread it into the center
hole of the mounting bracket (FF). Tighten the
bolt (DD) securely.

Ƒ Firmly pull on the mounting plate (D) to

verify it is securely attached to the mounting
bracket(FF).

U

P

/Hau

t

/Arri

b

a

GND
Terre
T

ie

rra

N

(Whit

B

la

e

n

/

c/Blanc

o

)

L

(Black

No

i

/

r/

N

e

g

ro

)

Making the electrical

5

connections

Ƒ Insert the junction box wires into the side of

the terminal block and around the ground
screw. Tighten terminal block screws using
the mini-screwdriver (GG) and ground screw to
secure the wires.

Ƒ Insert the white wire from the junction box

into the terminal marked “N (White)”.

Ƒ Insert the black wire from the junction box

into the terminal marked “L (Black)”.

Ƒ Connect the bare or green ground wire

from the junction box to the ground screw
(marked with “GND”).

UP/Haut/Arriba

GND
Terre
Tierra

N (White/
Blanc/Blanco)

L (Black/
Noir/Negro)

FF

ONT

FR

D

D

DD

Mounting the light fixture

6

NOTICE: The two pins on the rear of the light xture must be
inserted into the terminal block for the light to work.

Ƒ Align the bottom edge of the light xture (B) with

the bottom edge of the mounting plate(D). Tilt
the light xture (B) toward the mounting plate (D),
making sure the light xture (B) is centered on
the mounting plate (D).

Ƒ Tighten the small mounting bolt (EE) securely

through the center of the mounting plate(D). Do
not overtighten.

Ƒ Push the rubber plug (AA) rmly into the

mounting bolt hole on the light xture (B).

22

AA

D

B

EE

Installation (continued)

Caulking around the light

7

fixture

Ƒ Caulk around the mounting plate (D) and

mounting surface with silicone sealant (not
included).

Operation

D

Adjusting the lamp heads

1

WARNING: Risk of re. Keep the lamp heads at least
2in. (51mm) from combustible materials.

CAUTION: Keep lamp heads 30° below horizontal to
avoid water damage and electrical shock.

Ƒ Turn the power on at the circuit breaker or fuse

and turn on the wall switch.

Ƒ If needed, gently grasp the lamp heads (A) and

tilt them up or down or side to side to adjust
the light coverage area.

A

THIS SIDE UP

180°

Rotating the sensor controls

2

downward

Ƒ Rotate the motion sensor (C) so the text faces

upward.

NOTICE: All clearances must be maintained. See Safety Information
on page 2.

NOTICE: The Noti™ mobile app must be downloaded to operate
the light xture. See Step 3 on page 9 for instructions.

THIS SIDE UP

180°

C

23 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Operation (continued)

Downloading the mobile app

3

Ƒ Download the Noti™ mobile app. Search for

the “Noti Video Solutions” app.

Ƒ iOS Devices – Download the app from the

App StoreSM.

Ƒ Android Devices – Download the app from

the Google Play™ store.

Viewing live video

5

The Noti app provides live-stream video from the
camera to a mobile device.

Ƒ Tap the name of the camera to be viewed.
Ƒ While in the live-stream screen, the following

options are available:

Ƒ Tap the video camera icon ( ) to start

recording live video. Tap again to stop
recording.

Ƒ Tap the camera icon (

image from the live-stream video.

Ƒ To return to the main app screen, tap the (

or “Back” button in the top left corner.

NOTE: All videos and images will be saved to the mobile
device currently being used to view the live-stream video.

) to save a still

Connecting the light to the

4

mobile app

NOTICE: The network password will be required to complete this
process.

Ƒ Ensure the power to the light is turned ON.

Allow 60 seconds for system boot-up.

Ƒ On the mobile device, go to Settings > Wi-Fi

and select “Noti_Video_SecurityXXXX”
(“XXXX” represents the unique MAC address
of each light xture) from the available Wi-Fi
networks.

Ƒ Once connected, open the Noti app. The app

will detect the new light.

Ƒ Select “Yes” to start the setup and the app will

guide you through the remaining steps.

NOTE: When creating a new Noti account, the username
and password must be a minimum of 4 characters and a
maximum of 12 characters. Alpha-numeric and/or special
characters may be used.

Understanding the motion

6

detection process

This light has dual motion detection technologies.

Ƒ The light is controlled by a 180° PIR (passive

infra-red) sensor. This sensor detects a
temperature difference moving in front of it.
When motion is detected after dark, the light will
come on at the selected “Full Bright Intensity”
level.

Ƒ The camera uses both the 180° PIR sensor as

well as a 100° image sensor located within the
camera software. The camera’s image sensor
will not activate unless the PIR sensor rst

)

detects a moving temperature difference within
the detection zone. The camera will record
motion day or night.

24

Operation (continued)

Using the event list

7

Tap the Events tab.

An event is created each time the camera senses
motion.

Ƒ Basic Service – The event list will show the date

and time the motion was detected.

Ƒ Premium Service (available for an additional

fee) – The event list will include the date, time,
and video of the event each time motion was
detected. The video of each event will also be
available to download for 30 days.

Adjusting the light settings

9

The light settings allow you to adjust the full bright
duration, the DualBrite® duration, and the percentages
of light intensity.

NOTE: Changes made to one light’s settings will not
affect another light’s settings.

Tap > Feature Settings > Light to select the light
settings.

Ƒ Full Bright Duration – This adjusts the amount

of time the light will stay ON after all motion has
stopped.

Ƒ DualBrite Duration – This adjusts the amount of

time the light stays ON at a reduced brightness
level when no motion is detected.

Ƒ Full Bright Intensity – This adjusts the intensity

level of the light when motion is detected.

Ƒ DualBrite Dimming Level – This adjusts the

intensity level of the light when no motion is
detected.

Receiving notifications

8

Tap > Feature Settings > Notications to select the
notication settings.

If notications are turned on, an email and/or push
notication is sent each time the camera senses
motion. Tap on the notication to be taken to the live­view video screen (Basic service) or the Event video
(Premium service).

Adjusting the camera

10

The camera settings allow you to adjust the motion
detection sensitivity, motion detection zones, and
video quality.

Tap > Feature Settings > Camera to select the
camera settings.

settings

NOTE: Changes made to one camera’s settings will not
affect another camera’s settings.

NOTE: The higher the “Sensitivity” setting, the greater the
possibility of false triggering. To reduce false triggering,
select a lower setting.

Ƒ Motion Detection – This adjusts the camera’s

sensitivity to motion in its eld of view.

Ƒ Motion Detection Zones – This adjusts the

camera’s detection area to include or exclude
zones in its eld of view.

Ƒ Auto Adjust – Disabling this setting allows

manual adjustments of the video’s quality
settings. For best performance, leave the Auto
Adjust ON.

25 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Operation (continued)

Setting the sensor for testing

11

NOTE: The light xture will operate during the day or
night during testing. The light will stay on for 5 seconds
after all motion is stopped.

NOTE: The light requires a 60-second boot-up period
before the camera will be fully operational.

Tap > Feature Settings > Camera > Motion
Detection to select the motion detection settings.

The light xture will automatically enter “Test” mode
whenever the “Motion Detection” option is selected.
The light xture will remain in “Test” until one of the
following actions occurs:

Ƒ The “Save” or “Cancel” option is selected.

Ƒ No movement during the testing process for 30

seconds.

Ƒ Three minutes have passed without changing

one of the on-screen settings.

Adjusting the motion sensor

12

detection zone

NOTE: The camera’s (E) detection zone is inside of the
light’s detection zone. When the motion sensor (C) for the
light is adjusted, the camera’s (E) motion sensor will also
be adjusted.

If motion is detected outside the camera’s detection zone,
the light may turn on but the camera will not record an
event.

Ƒ Perform a “walk test”: walk in an arc across

the front of the motion sensor (C).

Ƒ Watch the light. The light will come on and the

red LED will ash indicating motion has been
detected.

Ƒ Stop, wait for the light to turn off, and then

begin walking again.

Ƒ Continue this process until the detection zone

has been established.

Ƒ If needed, gently grasp the motion sensor (C)

and move it from side to side or up and down
to adjust the detection zone.

Ƒ Adjust the “Motion Detection” sensitivity to

High, Medium, or Low as needed.

NOTE: The motion sensor (C) is more sensitive to motion
moving across the front of the sensor. The motion sensor
(C) is less sensitive to motion moving directly toward the
front of the sensor.

26

E

C

C and E

Operation (continued)

13

15

Adding multiple users

The Noti system allows control of multiple users
within an account.

Tap > Advanced Settings > Manage Multiple Users.

Ƒ Tap the “Add Viewers” button and type the

email address in the “To:” eld.

Ƒ Tap the “Send” button.

NOTE: When adding multiple users, separate the email
addresses with a semicolon.

Using manual mode

Manual mode overrides the motion sensor (C) and will
turn the light on at the preset
level

. This feature works day or night. The motion sensor

(C) will reset to motion sensing mode at sunrise.

Ƒ On the main screen under the “Systems” tab,

choose “ON”, “OFF”, or “AUTO” to control the
lights for the selected Noti system.

“Full Bright Intensity”

Care and Cleaning

Adding system name and

14

Add a name and photo to represent the Noti system
on the mobile device. The photo will be placed inside
the blue circle icon next to the selected Noti system.

Tap > Advanced Settings > System Name/Photo.

16

To delete a Noti system from an account:

photo

Ƒ Enter a name for the Noti system.
Ƒ Select an existing photo and take a new photo

to represent the Noti system.

NOTE: The light settings and name are stored in the light
xture. The photo is locally stored on the mobile devaice
and is only visible on that device.

Deleting a Notifi system

Ƒ Turn off the wall switch controlling the Noti

system.

Ƒ On the main “Systems” screen, wait for the

system to go ofine (the system name and
image will turn gray).

Ƒ Once ofine, swipe the Noti system to be

deleted to the left and tap the trashcan icon
( ).

Ƒ To prolong the original appearance, clean the light xture with clear water and a soft, damp cloth only.

Ƒ Do not use paints, solvents, or other chemicals on this light xture. They could cause a premature

deterioration of the nish. This is not a defect in the nish and will not be covered by the warranty.

Ƒ Do not spray the light xture with a hose or power washer.

Ƒ To clean the camera lens, use a dry, microber cloth only.

27 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Troubleshooting

Problem Possible Cause Solution

The light will not come on. Ƒ The light switch is turned off. Ƒ Turn the light switch on.

The light comes on during
the day.

The light comes on for no
apparent reason.

The lights stay ON too late
in the “DualBrite Duration”
setting.

The lights do not stay ON
late enough in the “DualBrite
Duration” setting.

Ƒ The fuse is blown or the circuit

breaker is turned off.

Ƒ The light is not scheduled to come

ON.

Ƒ The circuit wiring is incorrect (if this

is a new installation).

Ƒ The motion sensor is aimed in the

wrong direction.

Ƒ The outside air temperature is close

to the same as a person’s body
heat.

Ƒ The light is scheduled to come ON. Ƒ Adjust the scheduled light

Ƒ The motion sensor may be sensing

small animals or automobile trafc.

Ƒ The “Motion Detection” setting is

set too high.

Ƒ The “DualBrite Duration” is

operating at the preset “DualBrite
Dimming Level” setting.

Ƒ The outside temperature is much

warmer or cooler than a person’s
body heat (summer or winter).

Ƒ The light xture is wired through a

dimmer or timer.

Ƒ The “DualBrite Duration” OFF time is

set to late.

Ƒ The “DualBrite Duration” OFF time is

set to early.

Ƒ Replace the fuse or turn the

circuit breaker on.

Ƒ Recheck the light operation

during the scheduled “DualBrite
Duration” (after sunset).

Ƒ Verify the wiring is correct.

Ƒ Re-aim the motion sensor to

cover the desired area.

Ƒ Increase the “Motion Detection”

setting.

operation in “DualBrite
Duration.”

Ƒ Decrease the “Motion Detection”

setting or reposition the motion
sensor.

Ƒ Decrease the “Motion Detection”

setting.

Ƒ The light xture is operating

normally under these
circumstances. The “DualBrite
Duration” time is adjustable.

Ƒ Decrease the “Motion Detection”

setting.

Ƒ Do not use a dimmer or timer to

control the light xture. Replace
the dimmer or timer with a
standard on/off wall switch.

Ƒ Adjust the “DualBrite Duration”

OFF time to the desired setting.

Ƒ Adjust the “DualBrite Duration”

OFF time to the desired setting.

28

Troubleshooting (continued)

Problem Possible Cause Solution

The lights stay on
continuously.

The lights ash on and off. Ƒ Heat or light from the lamp heads

The light xture is not
responding to the app.

The app is not nding the light
xture.

Motion notications are not
being sent to the app.

Ƒ The motion sensor may be picking

up a heat source, such as an air
vent, dryer vent, or brightly painted,
heat-reective surface.

Ƒ The motion sensor is in manual

mode.

Ƒ The light xture is wired through a

dimmer or timer.

Ƒ The light xture is on the same

circuit as a motor, transformer, or
uorescent bulb.

may be turning the motion sensor
on and off.

Ƒ Heat is being reected from other

objects and may be turning the
motion sensor on and off.

Ƒ The light is ofine (the system name

and image are gray).

Ƒ The light is unable to connect to the

wi- (the system name and image
are gray).

Ƒ The light may have been deleted

from the account.

Ƒ Notications are turned off in the

app.

Ƒ Motion is not being detected inside

the camera’s detection zone.

Ƒ Decrease the “Motion Detection”

setting or reposition the motion
sensor.

Ƒ Turn the manual mode option to

Off or Auto. See Using manual
mode on page 12.

Ƒ Do not use a dimmer or timer to

control the light xture. Replace
the dimmer or timer with a
standard on/off wall switch.

Ƒ Install the light xture on

a circuit without motors,
transformers, or uorescent
bulbs.

Ƒ Reposition the lamp heads away

from the motion sensor.

Ƒ Decrease the “Motion Detection”

setting or reposition the motion
sensor.

Ƒ Ensure the light has power.

Ƒ Ensure the light is connected to

the wi- router.

Ƒ Turn the power to the light off.

Wait 30 seconds and turn the
power on. Wait 60 seconds for
the light to boot-up.

Ƒ Reconnect the light to the app

(see step 4, page 9).

Ƒ Turn notications on in the app

(see step 8, page 10).

Ƒ Re-aim the motion sensor

to cover the desired area or
increase the “Motion Detection”
setting.

29 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Questions, problems, missing parts?

Before returning to the store, call Deant Customer Service

8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday

1-866-308-3976

HOMEDEPOT.COM

Retain this manual for future use.

Apple and the Apple logos are trademarks of Apple Inc., registered in the U.S., and other countries. App Store is a

Wi-Fi® is a registered trademark of Wi-Fi Alliance

service mark of Apple Inc.

Google Play is a trademark of Google Inc.

Android is a trademark of Google Inc.