HeathCo Heath Zenith 7303 Instruction Manual

Wireless Push Button
Accessory

© 2014 HeathCo LLC 207351-01A

Model

Wireless

push

button

Hardware

pack

7303

✔ ✔

The Heath®/Zenith wireless push button accessory works with any Heath®/Zenith
wireless chime. This package includes (Style of push button may vary from illustration):

-2-

207351-01

Figure 1

WARNING: To prevent possible SERIOUS INJURY or DEATH:

• NEVER allow small children near batteries.

• If battery is swallowed, immediately notify doctor.

Figure 2

1 2 3 4 5 6 7 8

A

MODEL: WL-4B

1 – MODE
2 – TUNE

C

H

I

M

E

V

O

L

U

M

E

ON

1 2

B

C

TUNE – HOLD
1 SECOND

.

SYNC – HOLD
3 SECONDS.
RESET – HOLD
10 SECONDS.

C

H

I

M

E

V

O

L

U

M

E

1. Remove orange battery tab from push button. Remove

back of case by pushing in tab on bottom with a small
screwdriver (see Figure 1). Remove orange battery tab.

2. Determine chime type. Look at the chime and determine

which type of chime will be connected to the push button
(see Figure 2).

• Chime < A > (2 Switches): The chime has only two

switches similar to the push button.

• Chime < B > (1 Button): The chime has a multi-function

button.

• Chime < C > (7 or 8 Jumpers or Switches): The chime

has a row of 7 or 8 jumpers or switches.

3. Sync the push button and chime.

Syncing Chime < A >

Step A1 (see Figure 3)

• If chime switch 1 is set to OFF, ensure push button
switch is set to OFF. Go to step A2.

• If chime switch 1 is set to ON, set push button switch
1 to ON. Go to step 4.

-3-

207351-01

Step A2 (see Figure 4)

• Unplug chime or remove chime batteries. Wait 30
seconds.

• Press and hold the push button within 20 seconds
after restoring power to the chime (plug in the chime
or install chime batteries). When the “Ding-Dong” tune
is played, the push button is synced with the chime.

• Go to step 4.

Syncing Chime < B >

Step B1 (see Figure 5)

• Set push button switch 1 to ON. Go to step B2.

Step B2 (see Figure 6)

• Press and hold the button on the chime until the chime
sounds a “Beep-Beep”.

• Press the push button within 30 seconds. The chime will
sound a “Beep-Beep” tone to indicate the push button
is synced. Wait 30 seconds before pressing the push
button to ensure operation.

• Go to step 4.

Syncing Chime < C >

Step C1 (see Figure 7)

• Set push button switch 1 to ON. Remove all jumpers
from positions 1 through 7 on the chime and place
jumpers only on positions 1 and 2, or set switches 1
and 2 to the ON position and switches 3 through 7 to
the OFF position.

• Go to step 4.

Figure 3

Figure 4

Chime

Setting

Push

Button

Setting

ON

1 2

ON

1 2

ON

1 2

ON

1 2

0

30 Sec.

0

20 Sec.

Continued

-4-

207351-01

4. Test range. Temporarily position push button where you

want it mounted. Press push button to verify chime and
push button work properly. If chime does not sound, see
Troubleshooting.

5. Mount push button. Use either screws or double sided

tape to mount push button.

• Screw Mounting: To mount with screws, remove
back of case by pushing in tab on bottom with a small
screwdriver (see Figure 1). Note: Remove material in
screw holes (if needed) before mounting with screws.
Attach back of case to door jamb or wall (see Figure

8). Snap front of push button on.

• Tape Mounting: When attaching push button using
double sided tape, make sure the surface of the door
jamb or wall is clean.

ON

1 2

Figure 5

Figure 6

Figure 7

Chime

Setting

Push

Button

Setting

0

30 Sec.

Chime Setting

Push Button Setting

ON

1 2

ON

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

Figure 8

-5-

207351-01

Push Button Chime < A > 2-Sounds

Chime

3-Sounds

Chime

Switch 2 - ON Switch 2 - ON Ding Ding

Switch 2 - OFF Switch 2 - ON Ding-Dong Ding-Dong

Switch 2 - OFF Switch 2 - OFF Ding-Dong Ding-Dong

Switch 2 - ON Switch 2 - OFF Ding Westminster

Push Button Chime < B > 2-Sounds

Chime

3-Sounds

Chime

Switch 2 - ON ——— Ding Ding

Switch 2 - OFF Push button on

chime to select
tune

Ding-Dong Ding-Dong or

Westminster

Tune Setting Table – Chime < A > and Push Button Settings*

Tune Setting Table – Chime < B > and Push Button Settings*

*For musical chimes, refer to the chime manual when selecting tune.

*For musical chimes, refer to the chime manual when selecting tune.

Tune Settings

Wireless chimes have different selectable tunes: Ding (one note tune) and Ding-Dong
(two note tune). Some models include Westminster (eight note tune) or musical
tunes. The factory setting is for the Ding-Dong (or Westminster if applicable) tune.
This tune can be changed by following the instructions in the Tune Setting Table.

Note: Only use switch 2 when changing the chime tune.

Continued

-6-

207351-01

Push Button Chime < C > 2-Sounds

Chime

3-Sounds

Chime

Switch 2 - ON Jumper 8 or

Switch 8 - OFF

Ding Ding

Switch 2 - OFF Jumper 8 or

Switch 8 - OFF

Ding-Dong Ding-Dong

Switch 2 - OFF Jumper 8 or

Switch 8 - ON

Ding-Dong Westminster

Switch 2 - ON Jumper 8 or

Switch 8 - ON

Ding Ding

Tune Setting Table – Chime < C > and Push Button Settings*

*For musical chimes, refer to the chime manual when selecting tune.

-7-

207351-01

Troubleshooting

1. PROBLEM: Chime does not sound or rang one time and quit.
A. POSSIBLE CAUSE: Batteries not installed correctly.
A. CORRECTIVE ACTION: Make sure batteries are installed according to

the diagram inside the push button and chime (if applicable).

B. POSSIBLE CAUSE: Batteries are dead.
B. CORRECTIVE ACTION: Check charge of push button and chime batteries

(if applicable) and replace if necessary.

C. POSSIBLE CAUSE: Push button and chime are not synced.
C. CORRECTIVE ACTION: Follow steps 2 and 3, page 2, to sync.

2. PROBLEM:

Batteries seem okay, but the chime does not work after installation.

A. POSSIBLE CAUSE: Chime or push button is mounted on metal or near

metal studs. Note: Metal reduces transmission range.

A. CORRECTIVE ACTION: Use 1/4 in. to 1/2 in. (6 to 13 mm) wood shims

to move chime or push button away from metal surface.

B. POSSIBLE CAUSE: Chime is mounted near concrete floor or wall. Note:

Concrete may reduce range.

B. CORRECTIVE ACTION: Move chime away from concrete surface.
C. POSSIBLE CAUSE: Chime and push button are installed too far apart.
C. CORRECTIVE ACTION: Locate chime closer to push button.

Note: The range of the wireless chime can vary with location, temperature, and
battery condition.

-8-

207351-01

Please contact us for assistance

before returning product to the

store or to HeathCo LLC.

If you experience a problem, follow this
guide. You may also contact us between
8:00 AM to 5:00 PM CST (M-F).

When contacting Technical Service,
please include the following informa­tion: Name, Street Address, Daytime
Phone Number, Email Address, Model
Number, Date of Purchase, Place of
Purchase, Product Issue, and DATED

SALES RECEIPT FOR WARRANTY
REQUESTS.

Technical Service

No Service Parts Available for this

Product

HeathCo LLC
2445 Nashville Road
Bowling Green, KY 42101, USA
ATTN: Technical Service

Internet: www.hzsupport.com
Phone: [phone] (English Only)
Fax: [phone]

Regulatory Information

This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada.
Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

The user is cautioned that changes or modifications not expressly approved by
the party responsible for regulatory compliance could void the user’s authority to
operate the equipment.

-9-

207351-01

HeathCo LLC reserves the right to discontinue and to change specifications at any
time without notice without incurring any obligation to incorporate new features in
previously sold products.

ONE YEAR LIMITED WARRANTY

This is a “Limited Warranty” which gives you specific legal rights. You may
also have other rights which vary from state to state or province to province.
For a period of one year from the date of purchase, any malfunction caused by
factory defective parts or workmanship will be corrected at no charge to you.
Not Covered - Repair service, adjustment and calibration due to misuse,
abuse or negligence, light bulbs, batteries, and other expendable items are not
covered by this warranty. Unauthorized service or modification of the product or
of any furnished component will void this warranty in its entirety. This warranty
does not include reimbursement for inconvenience, installation, setup time,
loss of use, unauthorized service, or return shipping charges.
This warranty covers only HeathCo LLC assembled products and is not
extended to other equipment and components that a customer uses in con­junction with our products.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION
OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT
FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF
ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUS­TOMER AND THERE SHALL BE NO LIABILITY ON THE PART OF HEATHCO
LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES, INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS
OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states or prov­inces do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.

Please keep your dated sales receipt, it is required for all warranty
requests.