HeathCo 60WRC31TX User Manual
This manual includes operating instructions for a variety of remote controlled products. All products work on the same principle and use the
Remote Controlled Products
same code setting information. Please read all instructional information and note any specific information pertaining to your particular product.
WARNINGS:
• FOR USE ONLY with 120 volt incandescent or halogen bulbs.
• DO NOT USE with fluorescent bulbs, appliances, power supplies, low voltage lighting, or any other electrical devices.
This manual applies to the following products:
•Transmitters
– Remote Control
– Indoor Wireless Motion Sensor
Note:
change to the code setting. Transmitter(s) and receiver(s)
must have the same code and group setting to work together. Switches 1 through 3 set the code. Switch 4 sets the
Group (A or B). See page 2 for switch locations.
Controls Group “A”
Receiver(s) and
Transmitter(s)
Receiver(s)
Code
CODE SETTINGS
Most single system installations will not require any
DIM
ON
OFF
Controls Group “B”
Receiver(s) and
Transmitter(s)
Receiver(s)
Code
AB
DIM
ON
OFF
Remote Control
Code
• Products are UL/cUL and/or FCC/IC tested and approved.
• Operational range of up to 100 feet.
Heath®/Zenith wireless lighting controls are designed to work
together. Simply determine which transmitter(s) you would
like to have control which receiver(s) and set the code setting
to match.
Note:
When operating more than one system independently of
each other, set each system to a different code. There are 8 codes
available by changing the settings of switches 1 through 3.
Receiver(s)
Code
Group A Group B
Example 2 - Code Switch Settings, System 2
When using a single group transmitter (
A-Switch, Remote Motion Sensor) the code and group settings
must match receiver(s) for the system to function properly.
Remote Control
Group Switch
Not Used on Remote
Receiver(s)
Code
FEATURES
Code
Remote Motion
Sensor Code
Receiver(s)
Code
i.e.
Door Transmitter, Add-
ENGLISH
Group A
(– Indicates Position of Switch)
Group Switch
Not Used On Remote
DRAFT COPY
Example 1 - Code Switch Settings, System 1
(Factory Setting)
Group B
Group A
Note:
This setting will work independently of examples 1 and 2
because the code setting is different.
Example 3 - Code Switch Settings with Single Transmitter
Note:
The channel can also be changed to reduce interference
problems from other wireless products (
garage door openers, etc.). See
information.
Group A
i.e.
wireless phones,
Troubleshooting Guide
for more
© 2004 DESA Specialty Products™ 598-1116-07
CODE SWITCH LOCATIONS
Code
ON
Switches
1 2 3 4
Code
Switches
Battery Cover
Remote Control
Indoor Wireless Motion Sensor
REMOTE CONTROL
Note:
One remote control is able to independently
operate two receiver units set on the same channel. If
more than two receiver units, operating independently,
are desired, additional remote controls will need to be
purchased.
1. Remove Tab from Battery Chamber. Remove cover from
back of transmitter. Gently pull tab out of battery chamber.
Slide cover onto transmitter.
ON
1 2 3 4
Battery
Chamber
(Type A23)
Rear View of Remote Control
2. Remote Control Functions. The three buttons on the left side
of the remote will operate one or more receiver units with
matching addresses. The three buttons on the right side of
the remote will operate a second set of one or more receiver
units.
• Device A/B ON: Turns on any receiver unit set to the same
channel as this remote control.
• Device A/B OFF: Turns off any receiver unit set to the same
channel as this remote control.
• Device A/B DIM: Activates the DIM feature for any receiver unit
set to the same channel as this remote control.
the DIM button steps through five brightness levels.
DRAFT COPY
Tab
Battery
Cover
Note:
Pressing
4543
1232
ON
Sensitivity
On-Time
Detect
Code
ON
Day / Night
5 1 Test
Night Only
Max Min
Note:
Note:
To independently operate a second receiver unit using a
single remote control, make sure the 4th dip switch on each
receiver is set to a different setting (see
• Device A - Slide dip switch 4 to the OFF position on each
receiver to be operated by these buttons.
• Device B - Slide dip switch 4 to the ON position on each
receiver to be operated by these buttons.
1 2 3 4
The “X” has been placed on the
switches to help clarify the code
settings on the previous page.
Close-Up of Typical Code Switch
(Factory Default Setting is Off)
Code Settings
section).
Device B DIM
Device A DIM
Device A ON
Device A OFF
Important: Wait 1 to 2 seconds after you press a transmitter
button before you press it again to allow the transmission to be
completed.
Note:
If light does not turn on or intermittently turns on and off when
transmitter buttons are pushed, see
Function Controls
2
Device B ON
Device B OFF
Troubleshooting Guide
598-1116-07
.
Loading...