Heat & Glo 6000GL-IPI-S, 6000GL-IPI-R, 6000GL-IPILP-S, 6000GL-IPILP-R Owner’s Manual

Para obtener un ejemplar en Español de este
Manual del propietario, visite www.heatnglo.com.

Models:
6000GL-IPI-S
6000GL-IPI-R
6000GL-IPILP-S
6000GL-IPILP-R

Pour demander un exemplaire en français de ce Manuel

du propriétaire, visitez www.heatnglo.com.

Owner’s Manual

Installation and Operation

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating
and maintenance
instructions included.

WARNING: If the information in these
instructions is not followed exactly, a fi re
or explosion may result causing property
damage, personal injury, or death.

• DO NOT store or use gasoline or other fl am-
mable vapors and liquids in the vicinity of this
or any other appliance.

• What to do if you smell gas

- DO NOT try to light any appliance.

- DO NOT touch any electrical switch. DO

NOT use any phone in your building.

- Immediately call your gas supplier from a

neighbor’s phone. Follow the gas suppli­er’s instructions.

- If you cannot reach your gas supplier, call

the fi re department.

• Installation and service must be performed
by a qualifi ed installer, service agency , or the
gas supplier.

This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer’s instructions
and the manufactured home construction and safety standard,

Title 24 CFR, Part 3280 or Standard for Installation in Mobile
Homes, CAN/CSA Z240MH, in Canada.

This appliance is only for use with the type(s) of gas indicated
on the rating plate.

• Read, understand and follow
these instructions for safe
installation and operation.

DO NOT

DISCARD

• Leave this manual with
party responsible for use
and operation.

WARNING

HOT SURFACES!

Glass and other surfaces are hot during
operation AND cool down.

Hot glass will cause burns.

• DO NOT touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as
fi replace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other fl ammable
materials.

• Keep clothing, furniture, draperies and other fl ammable
materials away.

This appliance has been supplied with an integral barrier
to prevent direct contact with the fi xed glass panel. DO
NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.

In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fi tter.

See Table of Contents for location of additional Commonwealth
of Massachusetts requirements.

Installation and service of this appliance should be
performed by qualifi ed personnel. Hearth & Home
Technologies suggests NFI certifi ed or factory trained
professionals, or technicians supervised by an NFI
certifi ed professional.

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev. R • 6/09 1

Read this manual before installing or operating this appliance.

Please retain this owner’s manual for future reference.

A. Congratulations

Congratulations on selecting a Heat & Glo gas fi replace, an
elegant and clean alternative to wood burning fi replaces.
The Heat & Glo gas fi replace you have selected is designed
to provide the utmost in safety, reliability, and effi ciency.

As the owner of a new fi replace, you’ll want to read and
carefully follow all of the instructions contained in this
owner’s manual. Pay special attention to all cautions and
warnings.

Homeowner Reference Information

This owner’s manual should be retained for future
reference. We suggest that you keep it with your other
important documents and product manuals.

The information contained in this owner’s manual, unless
noted otherwise, applies to all models and gas control
systems.

Your new Heat & Glo gas fi replace will give you years of
durable use and trouble-free enjoyment. Welcome to the
Heat & Glo family of fi replace products!

We recommend that you record the following pertinent
information about your fi replace.

Model Name: ___________________________________________ Date purchased/installed: __________________
Serial Number: __________________________________________ Location on fi replace: _____________________
Dealership purchased from: _______________________________ Dealer Phone: __________________________
Notes: _______________________________________________________________________________________
_____________________________________________________________________________________________

Listing Label Information/Location

This product may be covered by one or more of the following patents: (Nos produits sont couverts par un ou plusieurs des brevets suivants): (United States)
4593510,4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495,
5452708,5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661,5941237, 5947112,5996575, 6006743, 6019099, 6048195,
6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2,
6729551, 6736133, 6748940, 6748942, D320652, D445174, D462436; (Canada)1297749, 2195264, 2225408; or other U.S. and foreign patents pending (ou
autresbrevetsamericainsetetrangersenattente).

Type of Gas

NotNot for for use use withwith solid solid fuel.fuel.
((NeNe doitdoit pas pas entre entre utilise utilise avecavec un un combustible combustible solide).solide).

Type Type ofof Gas Gas (Sorte(Sorte DeDe Gaz)Gaz)::

NNAATURALTURAL GASGAS

Gas and Electric
Information

Minimum Minimum Permissible Permissible Gas Gas SupplySupplyfor for PurposesPurposes ofof Input Input Adjustment.Adjustment.
ApprovedApproved Minimum Minimum (De (De Gaz)Gaz)AcceptableAcceptable 0.00.0inin w.c.w.c. (Po.(Po.Col.Col. d’eau)d’eau)
Maximum Maximum PressurePressure(Pression)(Pression) 0.00.0inin w.c.w.c. (Po.(Po.Col.Col. d’eau)d’eau)
Maximum Maximum ManifoldManifoldPressurePressure(Pression)(Pression) 0.00.0 inin w.c.w.c. (Po.(Po. Col.Col.d’eau)d’eau)
Minimum Minimum ManifoldManifold PressurePressure (Pression)(Pression) 0.00.0 inin w.c.w.c. (Po.(Po. Col.Col.d’eau)d’eau)
Total Total ElectricalElectrical Requirements: Requirements: 0 00Vac, 000Vac, 00Hz.,00Hz., lessless thanthan0000AmperesAmperes

ALTITUDE:ALTITUDE: 0-0000 0-0000 FT.FT. 0000-0000FT.0000-0000FT.
MAX.MAX.INPUT INPUT BTUH:BTUH: 00,00000,000 00,00000,000
MIN.MIN. INPUT INPUT BTUH:BTUH: 00,00000,000 00,00000,000
ORIFICE ORIFICE SIZE:SIZE: #XXXXX#XXXXX #XXXXX#XXXXX

The model information regarding your specifi c fi replace can be found on
the rating plate usually located in the control area of the fi replace.

Heat & Glo, a brand of Hearth & Home Technologies, Inc.
7571 215th Street West, Lakeville, MN 55044

ThisThisappliance appliance mustmust bebeinstalled installed inin accordanceaccordance withwith local local codes,codes, ifif any;any; ifif not,not, follow follow ANSIANSI Z223.1Z223.1
ininthe the USA USA ororCAN/CGA CAN/CGA B149 B149 installation installation codes.codes.(Installer (Installer l’appareill’appareilselon selon leslescodes codes ouou reglementsreglements

locauxlocaux ou,ou, enen l’absencel’absence dede telstels reglements, reglements, selon selon les les codescodes d’installationd’installation CAN/CGA-B149.)CAN/CGA-B149.)

ANSIANSIZ21XX-XXXXZ21XX-XXXX · · CSA CSA 2.XX-MXX2.XX-MXX · · UL307BUL307B

ININCANADACANADA

Model:Model:

(Modele):(Modele):

SerialSerial

(Serie):(Serie):

XXXXXXXXXXXXXXXX

XXXXXXXXXXXXXXXX

MADEMADE ININ USAUSA

Model Number

Serial Number

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev. R • 6/092

Safety Alert Key:

• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.

• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• NOTICE: Used to address practices not related to personal injury.

Table of Contents

A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Î

B. Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1 Listing and Code Approvals

A. Appliance Certifi cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

B. Tempered Glass Specifi cations . . . . . . . . . . . . . . . . . . . . . 7

C. BTU Specifi cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . . 7

E. Non-Combustible Materials Specifi cation. . . . . . . . . . . . . . 7

F. Combustible Materials Specifi cation . . . . . . . . . . . . . . . . . 7

G. Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

H. Requirements for the Commonwealth of Massachusetts . . 8

User Guide

2 Operating Instructions

A. Gas Fireplace Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

B. Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

C. Fan Kit (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

D. Clear Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

E. Decorative Doors and Fronts . . . . . . . . . . . . . . . . . . . . . . 10

F. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

G. Remote Controls, Wall Controls and Wall Switches . . . . . 10

H. Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . 10

I. Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 11

J. After Fireplace is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

K. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 12

3 Maintenance and Service

A. Maintenance Tasks-Homeowner . . . . . . . . . . . . . . . . . . . 13

B. Maintenance Tasks-Qualifi ed Service Technician . . . . . . 14

Installer Guide

4 Getting Started

A. Typical Appliance System. . . . . . . . . . . . . . . . . . . . . . . . . 16

B. Design and Installation Considerations . . . . . . . . . . . . . . 17

C. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . 17

D. Inspect Appliance and Components . . . . . . . . . . . . . . . . . 17

5 Framing and Clearances

A. Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . 18

B. Constructing the Appliance Chase . . . . . . . . . . . . . . . . . . 19

C. Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

D. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 20

6 Termination Locations

A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 21

7 Vent Information and Diagrams

A. Approved Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

B. Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

C. Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

D. Measuring Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

E. Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

8 Vent Clearances and Framing

A. Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . . 33

B. Wall Penetration Framing . . . . . . . . . . . . . . . . . . . . . . . . . 33

C. Install the Ceiling Firestop . . . . . . . . . . . . . . . . . . . . . . . . 34

D. Install Attic Insulation Shield . . . . . . . . . . . . . . . . . . . . . . . 35

E. Installing the Optional Heat-Zone-Gas Kit . . . . . . . . . . . . 35

9 Appliance Preparation

A. Top Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

B. Rear Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

C. Installing the Non-combustible Board. . . . . . . . . . . . . . . . 38

D. Securing and Leveling the Appliance . . . . . . . . . . . . . . . . 38

10 Installing Vent Pipe (DVP and SLP Pipe)

A. Assemble Vent Sections (DVP Pipe Only) . . . . . . . . . . . . 39

B. Assemble Vent Sections (SLP Pipe Only) . . . . . . . . . . . . 40

C. Assemble Slip Sections . . . . . . . . . . . . . . . . . . . . . . . . . . 40

D. Secure the Vent Sections . . . . . . . . . . . . . . . . . . . . . . . . . 41

E. Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . . 41

F. Install Decorative Ceiling Components (SLP only) . . . . . . 42

G. Install Metal Roof Flashing . . . . . . . . . . . . . . . . . . . . . . . . 43

H. Assemble and Install Storm Collar . . . . . . . . . . . . . . . . . . 43

I. Install Vertical Termination Cap . . . . . . . . . . . . . . . . . . . . 44

J. Install Decorative Wall Components (SLP only) . . . . . . . . 44

K. Heat Shield Requirements for Horizontal Termination . . . 44
L. Install Horizontal Termination Cap (DVP and SLP Pipe) . 45

11 Gas Information

A. Fuel Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

B. Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . 46

12 Electrical Information

A. Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

B. IntelliFire Ignition System Wiring . . . . . . . . . . . . . . . . . . . 47

C. Optional Accessories Requirements . . . . . . . . . . . . . . . . 47

D. Electrical Service and Repair . . . . . . . . . . . . . . . . . . . . . . 48

E. Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 49

F. Wall Switch Installation for Fan (Optional) . . . . . . . . . . . . 49

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev. R • 6/09 3

13 Finishing

A. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 50

B. Facing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

C. Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

14 Appliance Setup

A. Remove Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . 52

B. Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . . 52

C. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

D. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

E. Install the Refractory . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

F. Ember Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

G. Install the Log Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . 54

H. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

I. Install the Mesh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

J. Install Trim and/or Surround . . . . . . . . . . . . . . . . . . . . . . . 56

K. Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

15 Troubleshooting

A. IntelliFire Ignition System . . . . . . . . . . . . . . . . . . . . . . . . . 57

16 Reference Materials

Î

A. Appliance Dimension Diagram . . . . . . . . . . . . . . . . . . . . . 59

B. Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . . 60

C. Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

D. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Î = Contains updated information.

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev. R • 6/094

Î

B. Limited Lifetime Warranty

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev. R • 6/09 5

Î

B. Limited Lifetime Warranty (continued)

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev. R • 6/096

1

1

Listing and Code Approvals

A. Appliance Certifi cation

MODELS: 6000GL-IPI-R, 6000GL-IPI-S
6000GL-IPILP-R, 6000GL-IPILP-S

LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Direct Vent Gas Appliance Heater
STANDARD: ANSI Z21.88-2000 • CSA2.33-M98 • UL307B

This product is listed to ANSI standards for “Vented Gas
Appliance Heaters” and applicable sections of “Gas Burn­ing Heating Appliances for Manufactured Homes and
Recreational Vehicles”, and “Gas Fired Appliances for
Use at High Altitudes”.

NOTICE: This installation must conform with local codes.
In the absence of local codes you must comply with the
National Fuel Gas Code, ANSI Z223.1-latest edition in
the U.S.A. and the CAN/CGA B149 Installation Codes in
Canada.

NOT INTENDED FOR USE AS A PRIMAR Y HEAT SOURCE.

This appliance is tested and approved as either supplemen­tal room heat or as a decorative appliance. It should not be
factored as primary heat in residential heating calculations.

B. Tempered Glass Specifi cations

Hearth & Home Technologies appliances manufactured
with tempered glass may be installed in hazardous loca­tions such as bathtub enclosures as defi ned by the Con-
sumer Product Safety Commission (CPSC). The tempered
glass has been tested and certifi ed to the requirements
of ANSI Z97.1 and CPSC 16 CFR 1202 (Safety Glazing
Certifi cation Council SGCC# 1595 and 1597. Architectur-
al Testing, Inc. Reports 02-31919.01 and 02-31917.01).

This statement is in compliance with CPSC 16 CFR Sec-
tion 1201.5 “Certifi cation and labeling requirements”
which refers to 15 U.S. Code (USC) 2063 stating “…Such
certifi cate shall accompany the product or shall otherwise
be furnished to any distributor or retailer to whom the
product is delivered.”

Some local building codes require the use of tempered
glass with permanent marking in such locations. Glass
meeting this requirement is available from the factory.
Please contact your dealer or distributor to order.

C. BTU Specifi cations

Models

U.S. (0-2000 ft.) or

Canada (2000-4500 ft.)

6000GL-IPI-R (NG)
6000GL-IPI-S (NG)

6000GL-IPILP-R
6000GL-IPILP-S

Maximum

Input

BTU/h

US 30,000 20,000

CAN 27,000 18,000

US 30,000 19,000

CAN 27,000 17,100

Minimum

Input

BTU/h

Orifi ce

Size

(DMS)

43
53

44
54

54
68

55
69

D. High Altitude Installations

NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.

When installing above 2000 feet elevation:

• In the USA: Reduce input rate 4% for each 1000 feet
above 2000 feet.

• In CANADA: Reduce input rate 10% for elevations
between 2000 feet and 4500 feet. Above 4500 feet,
consult local gas utility.

Check with your local gas utility to determine proper
orifi ce size.

E. Non-Combustible Materials Specifi cation

Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick, tile, concrete,
slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a
Vertical Tube Furnace at 750 ºC and UL763 shall be

considered non-combustible materials.

F. Combustible Materials Specifi cation

Materials made of or surfaced with wood, compressed pa­per, plant fi bers, plastics, or other material that can ignite
and burn, whether fl ame proofed or not, or plastered or
unplastered shall be considered combustible materials.

G. Electrical Codes

NOTICE: This appliance must be electrically wired and
grounded in accordance with local codes or, in the absence
of local codes, with National Electric Code ANSI/NFPA

70-latest edition or the Canadian Electric Code CSA
C22.1.

• A 110-120 VAC circuit for this product must be pro-

tected with ground-fault circuit-interrupter protection,
in compliance with the applicable electrical codes,
when it is installed in locations such as in bathrooms
or near sinks.

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev. R • 6/09 7

Note: The following requirements reference various
Massachuset ts and national codes not contained in this
document.

H. Requirements for the Commonwealth of

Massachusetts

For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in
whole or in part for residential purposes, including those
owned or operated by the Commonwealth and where the
side wall exhaust vent termination is less than seven (7)
feet above fi nished grade in the area of the venting, in-
cluding but not limited to decks and porches, the following
requirements shall be satisfi ed:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented
gas fueled equipment, the installing plumber or gas fi tter
shall observe that a hard wired carbon monoxide detector
with an alarm and battery back-up is installed on the fl oor
level where the gas equipment is to be installed. In addi­tion, the installing plumber or gas fi tter shall observe that
a battery operated or hard wired carbon monoxide detec­tor with an alarm is installed on each additional level of
the dwelling, building or structure served by the side wall
horizontal vented gas fueled equipment. It shall be the
responsibility of the property owner to secure the services
of qualifi ed licensed professionals for the installation of
hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fu­eled equipment is installed in a crawl space or an attic,
the hard wired carbon monoxide detector with alarm and
battery back-up may be installed on the next adjacent
fl oor level.
In the event that the requirements of this subdivision can
not be met at the time of completion of installation, the
owner shall have a period of thirty (30) days to comply
with the above requirements; provided, however, that dur­ing said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.

Inspection

The state or local gas inspector of the side wall horizon­tally vented gas fueled equipment shall not approve the
installation unless, upon inspection, the inspector ob­serves carbon monoxide detectors and signage installed
in accordance with the provisions of 248 CMR 5.08(2)(a)1
through 4.

Exemptions

The following equipment is exempt from 248 CMR

5.08(2)(a)1 through 4:

• The equipment listed in Chapter 10 entitled “Equipment

Not Required To Be Vented” in the most current edition
of NFPA 54 as adopted by the Board; and

• Product Approved side wall horizontally vented gas fu-

eled equipment installed in a room or structure separate
from the dwelling, building or structure used in whole or
in part for residential purposes.

MANUFACTURER REQUIREMENTS
Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall
horizontally vented gas equipment provides a venting
system design or venting system components with the
equipment, the instructions provided by the manufacturer
for installation of the equipment and the venting system
shall include:

• Detailed instructions for the installation of the venting

system design or the venting system components; and

• A complete parts list for the venting system design or

venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall
horizontally vented gas fueled equipment does not pro­vide the parts for venting the fl ue gases, but identifi es
“special venting systems”, the following requirements
shall be satisfi ed by the manufacturer:

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accor­dance with the above provisions shall comply with NFPA
720 and be ANSI/UL 2034 listed and IAS certifi ed.

Signage

A metal or plastic identifi cation plate shall be permanent-
ly mounted to the exterior of the building at a minimum
height of eight (8) feet above grade directly in line with the
exhaust vent terminal for the horizontally vented gas fu­eled heating appliance or equipment. The sign shall read,
in print size no less than one-half (1/2) in. in size, “GAS

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OB­STRUCTIONS”.

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev. R • 6/098

• The referenced “special venting system” instructions

shall be included with the appliance or equipment in­stallation instructions; and

• The “special venting systems” shall be Product Ap-

proved by the Board, and the instructions for that sys­tem shall include a parts list and detailed installation
instructions.

A copy of all installation instructions for all Product Ap­proved side wall horizontally vented gas fueled equip­ment, all venting instructions, all parts lists for venting
instructions, and/or all venting design instructions shall
remain with the appliance or equipment at the completion
of the installation.

See Gas Connection section for additional Common­wealth of Massachusetts requirements.

2

2

Operating Instructions

User Guide

A. Gas Fireplace Safety

WARNING

HOT SURFACES!

Glass and other surfaces are hot during
operation AND cool down.

Hot glass will cause burns.

• DO NOT touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as
fi replace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other
fl ammable materials.

• Keep clothing, furniture, draperies and other fl ammable
materials away.

This appliance has been supplied with an integral barrier
to prevent direct contact with the fi xed glass panel. DO
NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.

If you expect that small children or vulnerable adults may
come into contact with this fi replace, the following precau-
tions are recommended:

• Install a physical barrier such as:

- A decorative fi rescreen.

- Adjustable safety gate.

• Install a switch lock or a wall/remote control with child
protection lockout feature.

• Keep remote controls out of reach of children.

• Never leave children alone near a hot fi replace, whether
operating or cooling down.

• Teach children to NEVER touch the fi replace.

• Consider not using the fi replace when children will be
present.

Contact your dealer for more information, or visit: www.
hpba.org/staysafe.

T o prevent unintended operation when not using your fi re-
place for an extended period of time (summer months,
vacations, trips, etc):

• Remove batteries from remote controls.

• Turn off wall controls.

• Unplug 3 volt adapter plug and remove batteries on IPI
models.

B. Your Fireplace

WARNING! DO NOT operate fi replace before read-
ing and understanding operating instructions. Failure

to operate fi replace according to operating instructions
could cause fi re or injury.

Figure 2.1 General Operating Parts

DECORATIVE DOORS

(NOT SHOWN)

SECTION 2.E.

FIXED GLASS ASSEMBLY

(NOT SHOWN)
SECTION 14.H.

MANTEL

FAN KIT

SECTION 2.C

HEARTH

CLEAR SPACE

SECTION 2.D.

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev. R • 6/09 9

C. Fan Kit (optional)

If desired, a fan kit may be added. Contact your dealer to
order the correct fan kit.

D. Clear Space

WARNING! DO NOT place combustible objects in front
of the fi replace or block louvers. High temperatures may
start a fi re. See Figure 2.2.

A void placing candles and other heat-sensitive objects on
mantel or hearth. Heat may damage these objects.

3 FT. IN FRONT OF FIREPLACE

CLE

AR SPACE

Figure 2.2 Clear Space

F. Fixed Glass Assembly

See Section 14.H.

G. Remote Controls, Wall Controls and Wall

Switches

Follow the instructions supplied with the control installed
to operate your fi replace:

For safety:

• Install a switch lock or a wall/remote control with child
protection lockout feature.

• Keep remote controls out of reach of children.

See your dealer if you have questions.

H. Before Lighting Fireplace

Before operating this fi replace for the fi rst time, have a
qualifi ed service technician:

• Verify all shipping materials have been removed from
inside and/or underneath the fi rebox.

• Review proper placement of logs, ember material and/or
other decorative materials.

• Check the wiring.

• Check the air shutter adjustment.

• Ensure that there are no gas leaks.

• Ensure that the glass is sealed and in the proper position
and that the integral barrier is in place.

WARNING! Risk of Fire or Asphyxiation! DO NOT op­erate fi replace with fi xed glass assembly removed.

E. Decorative Doors and Fronts

WARNING! Risk of Fire! Install ONLY doors or fronts
approved by Hearth & Home Technologies. Unapproved
doors or fronts may cause fi replace to overheat.

This fireplace has been supplied with an integral
barrier to prevent direct contact with the fi xed glass
panel. DO NOT operate the fi replace with the barrier
removed.

Contact your dealer or Hearth & Home Technologies if
the barrier is not present or help is needed to properly
install one.

For more information refer to the instructions supplied with
your decorative door or front.

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev. R • 6/0910

I. Lighting Instructions (IPI)

The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer. To prolong battery
life, remove them when using the transformer.

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fi re or explosion

may result causing property damage, personal injury or loss of life.

A. This appliance is equipped with an

intermittent pilot ignition (IPI) device
which automatically lights the burn­er. DO NOT try to light the burner by
hand.

B. BEFORE LIGHTING, smell all around

the appliance area for gas. Be sure to
smell next to the fl oor because some
gas is heavier than air and will settle
on the fl oor.

WHA T TO DO IF YOU SMELL GAS

• DO NOT try to light any appliance.

• DO NOT touch any electric switch; do
not use any phone in your building.

WARNING:

DO NOT CONNECT 110 VAC TO
THE CONTROL VALVE.

Improper installation, adjustment, al­teration, service or maintenance can
cause injury or property damage. Re­fer to the owner’s information manual
provided with this appliance.

This appliance needs fresh air for
safe operation and must be installed
so there are provisions for adequate
combustion and ventilation air.

If not installed, operated, and main­tained in accordance with the man­ufacturer’s instructions, this product
could expose you to substances in fuel
or fuel combustion which are known to
the State of California to cause can­cer, birth defects, or other reproductive
harm.

Keep burner and control compartment
clean. See installation and operating
instructions accompanying appliance.

• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.

• If you cannot reach your gas sup­plier, call the fi re department.

C. DO NOT use this appliance if any

part has been under water. Imme­diately call a qualifi ed service tech-
nician to inspect the appliance and
to replace any part of the control
system and any gas control which
has been under water.

CAUTION:

Hot while in operation. DO NOT touch.
Keep children, clothing, furniture, gaso­line and other liquids having fl ammable
vapors away.

DO NOT operate the appliance with
fi xed glass assembly removed, cracked
or broken. Replacement of the fi xed
glass assembly should be done by a
licensed or qualifi ed service person.

NOT FOR USE

WITH SOLID FUEL

For use with natural gas and propane.
A conversion kit, as supplied by the
manufacturer, shall be used to convert
this appliance to the alternate fuel.

Also Certifi ed for Installation in a
Bedroom or a Bedsitting Room.

For assistance or additional informa­tion, consult a qualifi ed installer, ser-
vice agency or the gas supplier.

LIGHTING

INSTRUCTIONS

(IPI)

1. Turn off all electric power to the appliance.

2. This appliance is equipped with an ignition

device which automatically lights the burner.

DO NOT try to light the burner by hand.

GAS

VALVE

3. Wait fi ve (5) minutes to clear out any gas.

Then smell for gas, including near the fl oor. If
you smell gas, STOP! Follow “B” in the Safety
Information located on the left side of this la­bel. If you do not smell gas, go to next step.

4. Turn on all electric power to the appliance.

5. To light the burner, fl ip the ON/OFF switch to

the “ON” position. (The ON/OFF switch may
include a wall switch if so equipped).

6. If the appliance will not operate, follow the in­structions “To Turn Off Gas to Appliance” and
call your service technician or gas supplier.

TO TURN OFF

GAS TO APPLIANCE

1. Turn wall control or ON/OFF switch to “OFF”.

2. Turn off all electric power to the appliance if

service is to be performed.

593-913F

Hearth & Home Technologies fi replace, please refer to www.fi replaces.com.

For additional information on operating your

Final inspection by

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev. R • 6/09 11

J. After Fireplace is Lit

Initial Break-in Procedure

• The fireplace should be run three to four hours
continuously on high.

• Turn the fi replace off and allow it to completely cool.

• Remove fi xed glass assembly. See Section 14.H.

• Clean fi xed glass assembly. See Section 3.

• Replace the fi xed glass assembly and run continuously
on high an additional 12 hours.

This cures the materials used to manufacture the fi re-
place.

NOTICE! Open windows for air circulation during fi re-
place break-in.

• Some people may be sensitive to smoke and odors.

• Smoke detectors may activate.

K. Frequently Asked Questions

ISSUE SOLUTIONS

Condensation on the glass

Blue fl ames

Odor from appliance

Film on the glass

Metallic noise

Is it normal to see the pilot fl ame burn
continually?

This is a result of gas combustion and temperature variations. As the appliance warms, this
condensation will disappear.

This is a result of normal operation and the fl ames will begin to yellow as the appliance is al-
lowed to burn for 20 to 40 minutes.

When fi rst operated, this appliance may release an odor for the fi rst several hours. This is caused
by the curing of the paint and the burning off of any oils remaining from manufacturing. Odor may
also be released from fi nishing materials and adhesives used around the appliance.

This is a normal result of the curing process of the paint and logs. Glass should be cleaned
within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing
process. A non-abrasive cleaner such as gas fi replace glass cleaner may be necessary. See
your dealer.

Noise is caused by metal expanding and contracting as it heats up and cools down, similar to
the sound produced by a furnace or heating duct. This noise does not affect the operation or
longevity of the appliance.

In an IntelliFire ignition system it is normal to see the pilot fl ame, but it should turn off when
ON/OFF is turned off.

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev. R • 6/0912

3

3

Maintenance and Service

Any safety screen or guard removed for servicing must be
replaced prior to operating the fi replace.

When properly maintained, your fi replace will give you
many years of trouble-free service. We recommend an­nual service by a qualifi ed service technician.

A. Maintenance Tasks-Homeowner

Installation and repair should be done by a qualifi ed service
technician only. The fi replace should be inspected before
use and at least annually by a professional service person.

The following tasks may be performed annually by the
homeowner. If you are uncomfortable performing any of
the listed tasks, please call your dealer for a service ap­pointment.

More frequent cleaning may be required due to lint from
carpeting or other factors. Control compartment, burner
and circulating air passageway of the fi replace must be
kept clean.

CAUTION! Risk of Burns! The fi replace should be turned
off and cooled before servicing.

Glass Cleaning

Frequency: Seasonally
By: Homeowner
Tools Needed: Protective gloves, glass cleaner, drop

cloth and a stable work surface.

CAUTION! Handle fi xed glass assembly with care.

Glass is breakable.

• Avoid striking, scratching or slamming glass

• Avoid abrasive cleaners

• DO NOT clean glass while it is hot

• Prepare a work area large enough to accommodate fi xed
glass assembly and door frame by placing a drop cloth
on a fl at, stable surface.

Note: Fixed glass assembly and gasketing may have res­idue that can stain carpeting or fl oor surfaces.

• Remove door or decorative front from fi replace and set
aside on work surface.

• See Section 14.H for instructions to remove fi xed glass
assembly.

• Clean glass with a non-abrasive commercially available
cleaner.

- Light deposits: Use a soft cloth with soap and water

- Heavy deposits: Use commercial fireplace glass

cleaner (consult with your dealer)

• Carefully set fi xed glass assembly in place on fi replace.
Hold glass in place with one hand and secure glass
latches with the other hand.

• Reinstall door or decorative front.

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev. R • 6/09 13

Doors, Surrounds, Fronts

Frequency: Annually
By: Homeowner
Tools needed: Protective gloves, stable work surface

• Assess condition of screen and replace as necessary.

• Inspect for scratches, dents or other damage and repair
as necessary.

• Check that louvers are not blocked.

• Vacuum and dust surfaces.

Remote Control

Frequency: Seasonally
By: Homeowner
Tools needed: Replacement batteries and remote con-

trol instructions.

• Locate remote control transmitter and receiver.

• Verify operation of remote. Refer to remote control
operation instructions for proper calibration and setup
procedure.

• Place batteries as needed in remote transmitters and
battery-powered receivers.

• Place remote control out of reach of children.

If not using your fi replace for an extended period of time
(summer months, vacations/trips, etc), to prevent unin­tended operation:

• Remove batteries from remote controls.

• Unplug 3 volt adapter plug on IPI models.

Venting

Frequency: Seasonally
By: Homeowner
Tools needed: Protective gloves and safety glasses.

• Inspect venting and termination cap for blockage or
obstruction such plants, bird nests, leaves, snow, debris,
etc.

• Verify termination cap clearance to subsequent construc­tion (building additions, decks, fences, or sheds). See
Section 6.

• Inspect for corrosion or separation.

• Verify weather stripping, sealing and fl ashing remains
intact.

• Inspect draft shield to verify it is not damaged or missing.

B. Maintenance Tasks-Qualifi ed Service

Technician

The following tasks must be performed by a qualifi ed ser-
vice technician.

Gasket Seal and Glass Assembly Inspection

Frequency: Annually
By: Qualifi ed Service Technician
T ools needed: Protective gloves, drop cloth and a stable

work surface.

• Inspect gasket seal and its condition.

• Inspect fi xed glass assembly for scratches and nicks that
can lead to breakage when exposed to heat.

• Confi rm there is no damage to glass or glass frame.
Replace as necessary.

• Verify that fi xed glass assembly is properly retained and
attachment components are intact and not damaged.
Replace as necessary.

Logs

Frequency: Annually
By: Qualifi ed Service Technician
Tools needed: Protective gloves.

• Inspect for damaged or missing logs. Replace as neces­sary . Refer to Section 14 for log placement instructions.

• Verify correct log placement and no fl ame impingement
causing sooting. Correct as necessary.

Firebox

Frequency: Annually
By: Qualifi ed Service Technician
Tools needed: Protective gloves, sandpaper, steel wool,

cloths, mineral spirits, primer and touch-up paint.

• Inspect for paint condition, warped surfaces, corrosion
or perforation. Sand and repaint as necessary.

• Replace fi replace if fi rebox has been perforated.

Control Compartment and Firebox Top

Frequency: Annually
By: Qualifi ed Service Technician
Tools needed: Protective gloves, vacuum cleaner, dust

cloths

• V acuum and wipe out dust, cobwebs, debris or pet hair.
Use caution when cleaning these areas. Screw tips that
have penetrated the sheet metal are sharp and should
be avoided.

• Remove all foreign objects.

• Verify unobstructed air circulation.

Burner Ignition and Operation

Frequency: Annually
By: Qualifi ed Service Technician
T ools needed: Protective gloves, vacuum cleaner, whisk

broom, fl ashlight, voltmeter, indexed drill bit set, and a
manometer.

• Verify burner is properly secured and aligned with pilot
or igniter.

• Clean off burner top, inspect for plugged ports, corrosion
or deterioration. Replace burner if necessary.

• Replace Glowing embers with new dime-size pieces.
DO NOT block ports or obstruct lighting paths. Refer to
Section 14 for proper ember placement.

• Verify batteries have been removed from battery back­up IPI systems to prevent premature battery failure or
leaking.

• Check for smooth lighting and ignition carryover to all
ports. Verify that there is no ignition delay.

• Inspect for lifting or other fl ame problems.

• Verify air shutter setting is correct. See Section 14 for
required air shutter setting. Verify air shutter is clear of
dust and debris.

• Inspect orifi ce for soot, dirt and corrosion. Verify orifi ce
size is correct. See Service Parts List for proper orifi ce
sizing.

• Verify manifold and inlet pressures. Adjust regulator as
required.

• Inspect pilot fl ame pattern and strength. See Figure 3.1
for proper pilot fl ame pattern. Clean or replace orifi ce
spud as necessary.

• Inspect thermocouple/thermopile or IPI fl ame sensing rod
for soot, corrosion and deterioration. Clean with emery
cloth or replace as required.

• Verify that there is not a short in fl ame sense circuit
by checking continuity between pilot hood and fl ame
sensing rod. Replace pilot as necessary.

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev. R • 6/0914

Figure 3.1 IPI Pilot Flame Patterns

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev. R • 6/09 15

HORIZONTAL

TERMINATION CAP

(SECTION 10.M )

4

4

A. Typical Appliance System

NOTICE: Illustrations and photos refl ect typical installations and are for design purposes only . Illustrations/diagrams are not
drawn to scale. Actual product may vary from pictures in manual

Getting Started

Note: Dual venting configurations
ARE NOT allowed. Appliance MUST

be vented EITHER vertically OR
horizontally.

VERTICAL TERMINATION CAP

(SECTION 10.J)

NON-COMBUSTIBLE ROOF FLASHING
MAINTAINS MINIMUM CLEARANCE
AROUND PIPE (SECTION 10.G)

STORM COLLAR
(SECTION 10.H)

Installer Guide

VENT PIPE (SECTIONS 7 and 9)

CEILING FIRESTOP
ON FLOOR OF ATTIC
(SECTION 8.C)

FRAMING/HEADER
(SECTION 5.B)

VENT PIPE PENETRATES ROOF
PREFERABLY WITHOUT AFFECTING
ROOF RAFTERS (SECTION 8.C)

ATTIC INSULATION SHIELD (NOT
SHOWN) MUST BE USED HERE TO
KEEP INSULATION AWAY FROM
VENT PIPE IF ATTIC IS INSULATED
(SECTION 8.D)

FRAMING HEADED OFF
IN CEILING JOISTS
(SECTION 8.C)

WALL SWITCH

MANTEL AND
MANTEL LEG
(SECTION 5.D)

SURROUND

OPTIONAL

GAS LINE
(SECTION 11)

Figure 4.1 Typical System

HEARTH EXTENSION

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev. R • 6/0916

B. Design and Installation Considerations

Heat & Glo direct vent gas appliances are designed to
operate with all combustion air siphoned from outside of
the building and all exhaust gases expelled to the outside.
No additional outside air source is required.

Installation MUST comply with local, regional, state and
national codes and regulations. Consult insurance carrier,
local building inspector, fi re offi cials or authorities having
jurisdiction over restrictions, installation inspection and
permits.

Before installing, determine the following:

• Where the appliance is to be installed.

• The vent system confi guration to be used.

• Gas supply piping requirements.

• Electrical wiring requirements.

• Framing and fi nishing details.

• Whether optional accessories—devices such as a fan,
wall switch, or remote control—are desired.

Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. For
assistance or additional information, consult a qualifi ed
service technician, service agency or your dealer.

C. Tools and Supplies Needed

Before beginning the installation be sure that the following
tools and building supplies are available.

Tape measure Framing material
Pliers High temperature caulking material
Hammer Phillips screwdriver
Gloves Framing square
Voltmeter Electric drill and bits (1/4 in.)
Plumb line Safety glasses
Level Reciprocating saw
Manometer Flat blade screwdriver
Non-corrosive leak check solution
1/2 - 3/4 in. length, #6 or #8 Self-drilling screws
One 1/4 in. female connection (for optional fan).

D. Inspect Appliance and Components

• Carefully remove the appliance and components from
the packaging.

• The vent system components and decorative doors and
fronts may be shipped in separate packages.

• If packaged separately, the log set and appliance grate
must be installed.

• Report to your dealer any parts damaged in shipment,
particularly the condition of the glass.

• Read all of the instructions before starting the instal-

lation. Follow these instructions carefully during the
installation to ensure maximum safety and benefi t.

WARNING! Risk of Fire or Explosion! Damaged parts
could impair safe operation. DO NOT install damaged, in­complete or substitute components. Keep appliance dry.

Hearth & Home T echnologies disclaims any responsibility for ,
and the warranty will be voided by, the following actions:

• Installation and use of any damaged appliance or vent

system component.

• Modifi cation of the appliance or vent system.

• Installation other than as instructed by Hearth & Home

Technologies.

• Improper positioning of the gas logs or the glass door.

• Installation and/or use of any component part not approved

by Hearth & Home Technologies.

Any such action may cause a fi re hazard.

WARNING! Risk of Fire, Explosion or Electric Shock!
DO NOT use this appliance if any part has been under

water. Call a qualifi ed service technician to inspect the
appliance and to replace any part of the control system
and/or gas control which has been under water.

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev. R • 6/09 17

5

5

Framing and Clearances

A. Selecting Appliance Location

When selecting a location for the appliance it is important to
consider the required clearances to walls (see Figure 5.1).

WARNING! Risk of Fire or Burns! Provide adequate
clearance around air openings and for service access.

Due to high temperatures, the appliance should be locat­ed out of traffi c and away from furniture and draperies.

A

1/2 IN.

G

A

B

C

TOP VENT

ONE 90º ELBOW

B

ALCOVE

INSTALLATION

NOTICE: Illustrations refl ect typical installations and are
FOR DESIGN PURPOSES ONLY. Illustrations/diagrams
are not drawn to scale. Actual installation may vary due to
individual design preference.

E

D

H

ABCD E F G H

Inches 51 42 72 56-5/8

Millimeters 1295 1067 1829 1438 559 451 203

Figure 5.1 Appliance Locations

REAR VENT,

HORIZONTAL TERMINATION,

TWO ELBOWS

B

D

REAR VENT,
NO ELBOWS

B

See Section D.

Mantel Projections

F

REAR VENT,
ONE ELBOW

B

D

22 17-3/4 8

D

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev. R • 6/0918

B. Constructing the Appliance Chase

A chase is a vertical box-like structure built to enclose the
gas appliance and/or its vent system. In cooler climates
the vent should be enclosed inside the chase.

NOTICE: Treatment of ceiling fi restops and wall shield
fi restops and construction of the chase may vary with the

type of building. These instructions are not substitutes
for the requirements of local building codes. Therefore,
you MUST check local building codes to determine the
requirements to these steps.

Chases should be constructed in the manner of all out­side walls of the home to prevent cold air drafting prob­lems. The chase should not break the outside building
envelope in any manner.

Walls, ceiling, base plate and cantilever fl oor of the chase
should be insulated. Vapor and air infi ltration barriers
should be installed in the chase as per regional codes for
the rest of the home. Additionally, in regions where cold
air infi ltration may be an issue, the inside surfaces may be
sheetrocked and taped for maximum air tightness.

To further prevent drafts, the wall shield and ceiling fi re-
stops should be caulked with high temperature caulk to
seal gaps. Gas line holes and other openings should be
caulked with high temperature caulk or stuffed with un­faced insulation. If the appliance is being installed on a
cement surface, a layer of plywood may be placed under­neath to prevent conducting cold up into the room.

C. Clearances

NOTICE: Install appliance on hard metal or wood surfaces
extending full width and depth. DO NOT install directly
on carpeting, vinyl, tile or any combustible material other
than wood.

WARNING! Risk of Fire! Maintain specifi ed air space
clearances to appliance and vent pipe:

• Insulation and other materials must be secured to prevent
accidental contact.

• The chase must be properly blocked to prevent blown
insulation or other combustibles from entering and
making contact with fi replace or chimney.

• Failure to maintain airspace may cause overheating and
a fi re.

A

E

F

B

C

D

G

J

I

*MINIMUM FRAMING DIMENSIONS

A B C** D E F G H I J

Rough

Opening

(Vent Pipe)

Inches 10 38-1/2 22 42 26-5/8 0 0 1/2 1/2 36

Rough

Opening

(Height)

Rough

Opening

(Depth)

Rough

Opening

(Width)

Clearance

to Ceiling

Combustible

Floor

Combustible

Flooring

Behind

Appliance

Sides of

Appliance

Front of

Appliance

H

Millimeters 254 978 559 1067 676 0 0 13 13 915

* Adjust framing dimensions for interior sheathing (such as sheetrock)

C** Add 12 inches for rear venting with one 90º elbow.

Figure 5.2 Clearances to Combustibles

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev. R • 6/09 19

D. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clear­ances as specifi ed. Framing or fi nishing material closer than
the minimums listed must be constructed entirely of noncom­bustible materials (i.e., steel studs, concrete board, etc).

Combustible Mantel Legs or Wall Projections

INTERIOR WALL

Combustible Mantels

4

3

2-1/2

5

Note: All measurements in inches.

18

12

11

10

9

8

7

6

5

14

13

12

11

10

MEASUREMENTS FROM

TOP EDGE OF THE OPENING

17

16

15

TO CEILING

25

19

18

32

TOP VIEW

A

FIREPLACE OPENING

MANTEL LEG OR WALL PROJECTIONS

B

If A minimum is ____, then B maximum is_____.

Inches

A

B

2-7/16 3-7/16 4-7/16 5-7/16 6-7/16 7-7/16

Millimeters

Inches

Millimeters

62 87 113 138 164 189

12345

25 51 76 102 127

∞

∞

Figure 5.4 Clearances to Mantel Legs or Wall Projections
(Acceptable on both sides of opening.)

Note: Measurement is taken from top of the

opening, NOT the top of the fi replace.

Figure 5.3 Minimum Vertical and Maximum Horizontal
Dimensions of Combustibles

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev. R • 6/0920

6

6

Termination Locations

A. Vent Termination Minimum Clearances

WARNING

Fire Risk.
Maintain vent clearance to combustibles as

specifi ed.

• DO NOT pack air space with insulation or other
materials.

Failure to keep insulation or other materials away
from vent pipe may cause overheating and fi re.

HORIZONTAL

OVERHANG

2 FT.
MIN.

GAS DIRECT VENT
TERMINATION CAP

20 INCHES MIN.

LOWEST

DISCHARGE

OPENING

H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING

X

12

ROOF PITCH

IS X/ 12

VERTICAL

WALL

6in.(minimum)upto20in.

AB

152 mm/508 mm

20 in. and over 0 in. minimum

18 in. minimum

457 mm

Gas, Wood or Fuel Oil

Termination Cap

B

A*

Gas

Termination

Cap **

If using decorative cap cover(s), this distance may need to be

*

increased. Refer to the installation instructions supplied with the
decorative cap cover.

In a staggered installation with both gas and wood terminations, the

**

wood termination cap must be higher than the gas termination cap.

Roof Pitch H (Min.) Ft.

Flat to 6/12...........................................................1.0*

Over 6/12 to 7/12 .................................................1.25*

Over 7/12 to 8/12 .................................................1.5*

Over 8/12 to 9/12 .................................................2.0*

Over 9/12 to 10/12 ...............................................2.5

Over 10/12 to 11/12 .............................................3.25

Over 11/12 to 12/12 .............................................4.0

Over 12/12 to 14/12 .............................................5.0

Over 14/12 to 16/12 .............................................6.0

Over 16/12 to 18/12 .............................................7.0

Over 18/12 to 20/12 .............................................7.5

Over 20/12 to 21/12 .............................................8.0

* 3 foot minimum in snow regions

Figure 6.1 Minimum Height From Roof To Lowest Discharge
Opening

Figure 6.2 Staggered Termination Caps

Heat & Glo • 6000GL-IPI-R, 6000GL-IPI-S • 2102-900 Rev. R • 6/09 21