Heat & Glo 6000GBV, 6000GBV-IPI, 6000GBV-LP, 6000GBV-IPILP Owner’s Manual

Models: 6000GBV 6000GBV-IPI 6000GBV-LP 6000GBV-IPILP

Owner’s Manual

Installation and Operation

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating and maintenance instructions included.

WARNING: If the information in these instructions is not followed exactly, a ﬁ re or explosion may result causing property damage, personal injury, or death.

• DO NOT store or use gasoline or other ﬂ am- mable vapors and liquids in the vicinity of this or any other appliance.

• What to do if you smell gas

- DO NOT try to light any appliance.

- DO NOT touch any electrical switch. DO

NOT use any phone in your building.

- Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s instructions.

- If you cannot reach your gas supplier, call

the ﬁ re department.

• Installation and service must be performed by a qualiﬁ ed installer, service agency , or the gas supplier.

• Read, understand and follow these instructions for safe installation and operation.

DO NOT

DISCARD

• Leave this manual with party responsible for use and operation.

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

• DO NOT touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as ﬁ replace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other ﬂ ammable materials.

• Keep clothing, furniture, draperies and other ﬂ ammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the ﬁ xed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas ﬁ tter.

A CO detector shall be installed in the room where the appliance in installed.

Installation and service of this appliance should be performed by qualiﬁ ed personnel. Hearth & Home Technologies suggests NFI certiﬁ ed or factory trained professionals, or technicians supervised by an NFI certiﬁ ed professional.

Heat & Glo • 6000GBV, 6000GBV-IPI • 2104-900 Rev. i • 6/09 1

Read this manual before installing or operating this appliance.

Please retain this owner’s manual for future reference.

A. Congratulations

Congratulations on selecting a Heat & Glo gas ﬁ replace, an elegant and clean alternative to wood burning ﬁ replaces. The Heat & Glo gas ﬁ replace you have selected is designed to provide the utmost in safety, reliability, and efﬁ ciency.

As the owner of a new ﬁ replace, you’ll want to read and carefully follow all of the instructions contained in this owner’s manual. Pay special attention to all cautions and warnings.

Homeowner Reference Information

This owner’s manual should be retained for future reference. We suggest that you keep it with your other important documents and product manuals.

The information contained in this owner’s manual, unless noted otherwise, applies to all models and gas control systems.

Your new Heat & Glo gas ﬁ replace will give you years of durable use and trouble-free enjoyment. Welcome to the Heat & Glo family of ﬁ replace products!

We recommend that you record the following pertinent information about your ﬁ replace.

Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: __________________________________________ Location on ﬁ replace: _____________________ Dealership purchased from: _______________________________ Dealer Phone: __________________________ Notes: _______________________________________________________________________________________ _____________________________________________________________________________________________

Listing Label Information/Location

This product may be covered by one or more of the following patents: (Nos produits sont couverts par un ou plusieurs des brevets suivants): (United States) 4593510,4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356,5341794, 5347983, 5429495, 5452708,5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485,5931661, 5941237, 594711 2,5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, D320652, D445174, D462436; (Canada)1297749, 2195264, 2225408; or other U.S. and foreign patents pending (ou autresbrevetsamericainsetetrangersenattente).

Type of Gas

Not for use with solid fuel . (Ne doit pas entre utilise avec un combustible solide).

Ty pe of Gas (Sorte De Gaz) :

NATURA L GAS

Gas and Electric Information

Minimum Permissible Gas Supply for Purpos es of Input Adjustment . Approved Minimum (De Gaz) Acceptabl e 0. 0 in w. c. (Po. Col. d’eau) Maximum Pressure (Pression) 0. 0 in w. c. (Po. Col. d’eau) Maximum Manifold Pressure (Pression) 0. 0 in w. c. (Po. Col. d’eau) Minimum Manifold Pressure (Pression) 0. 0 in w. c. (Po. Col. d’eau) T o tal Electrical Requirements: 000V ac, 00Hz., less than 00 Ampere s

AL TI TUDE : 0-0000 FT . 0000-0000FT . MAX. INPU T BTUH: 00,000 00,000 MIN. INPU T BTUH: 00,000 00,000 ORIFICE SIZE: #XXXXX #XXXXX

The model information regarding your speciﬁ c ﬁ replace can be found on the rating plate usually located in the control area of the ﬁ replace.

Heat & Glo, a brand of Hearth & Home Technologies, Inc. 7571 215th Street West, Lakeville, MN 55044

This appliance must be installed in accordance with local codes, if any; if not, follow ANSI Z223.1 in the USA or CAN/CG A B149 installation codes. (Installer l’ appa re il selon les codes ou regl emen ts

lo caux ou , en l’absence de tels reglements, selon les codes d’in stallation CAN/CGA-B149.)

ANSI Z21X X-XXXX · CS A 2.XX-MXX · UL307B

IN CANADA

Mode l:

(Modele):

Serial

(Serie):

XXXXXXXX

MADE IN US A

Model Number

Serial Number

Heat & Glo • 6000GBV, 6000GBV-IPI • 2104-900 Rev. i • 6/092

Safety Alert Key:

• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.

• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• NOTICE: Used to address practices not related to personal injury.

Table of Contents

A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

B. Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1 Listing and Code Approvals

A. Appliance Certiﬁ cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

B. Tempered Glass Speciﬁ cations . . . . . . . . . . . . . . . . . . . . . 7

C. BTU Speciﬁ cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . . 7

E. Non-Combustible Materials Speciﬁ cation. . . . . . . . . . . . . . 7

F. Combustible Materials Speciﬁ cation . . . . . . . . . . . . . . . . . 7

G. Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

User Guide

2 Operating Instructions

A. Gas Fireplace Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

B. Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

C. Fan Kit (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

D. Clear Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

E. Decorative Doors and Fronts . . . . . . . . . . . . . . . . . . . . . . . 9

F. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

G. Remote Controls, Wall Controls and Wall Switches . . . . . . 9

H. Outside Air (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

I. Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . 9

J. Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 10

K. Lighting Instructions (Standing Pilot) . . . . . . . . . . . . . . . . 11

L. After Fireplace is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

M. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 12

3 Maintenance and Service

A. Maintenance Tasks-Homeowner . . . . . . . . . . . . . . . . . . . 13

B. Maintenance Tasks-Qualiﬁ ed Service Technician . . . . . . 14

Installer Guide

4 Getting Started

A. Typical Appliance System. . . . . . . . . . . . . . . . . . . . . . . . . 16

B. Design and Installation Considerations . . . . . . . . . . . . . . 17

C. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . 17

D. Inspect Appliance and Components . . . . . . . . . . . . . . . . . 17

E. Negative Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

5 Framing and Clearances

A. Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . 19

B. Constructing the Appliance Chase . . . . . . . . . . . . . . . . . . 20

C. Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

D. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 21

6 Termination Locations

A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 22

7 Vent Information and Diagrams

A. Vent Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

B. Vent System Conﬁ guration . . . . . . . . . . . . . . . . . . . . . . . . 23

8 Vent Clearances and Framing

A. Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . . 24

B. Wall and Ceiling Penetration Framing . . . . . . . . . . . . . . . 24

C. Vertical Penetration Framing . . . . . . . . . . . . . . . . . . . . . . 24

9 Appliance Preparation

A. Installing Outside Air Kit Damper Assembly . . . . . . . . . . . 25

B. Gas and Electrical Connections . . . . . . . . . . . . . . . . . . . . 25

C. Installing the Non-combustible Board. . . . . . . . . . . . . . . . 25

D. Securing and Leveling the Appliance . . . . . . . . . . . . . . . . 26

10 Installing Vent Pipe

A. Assembly of Vent Sections . . . . . . . . . . . . . . . . . . . . . . . . 27

B. Attaching Vent to Firebox . . . . . . . . . . . . . . . . . . . . . . . . . 27

C. Securing Vent Sections . . . . . . . . . . . . . . . . . . . . . . . . . . 27

D. Install Attic Insulation Shield . . . . . . . . . . . . . . . . . . . . . . . 27

11 Gas Information

A. Fuel Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

B. Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . 28

12 Electrical Information

A. Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

B. Standing Pilot Ignition System Wiring . . . . . . . . . . . . . . . 29

C. IntelliFire Ignition System Wiring . . . . . . . . . . . . . . . . . . . 29

D. Optional Accessories Requirements . . . . . . . . . . . . . . . . 29

E. Electrical Service and Repair . . . . . . . . . . . . . . . . . . . . . . 30

F. Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 31

G. Wall Switch Installation for Fan (Optional) . . . . . . . . . . . . 31

Heat & Glo • 6000GBV, 6000GBV-IPI • 2104-900 Rev. i • 6/09 3

13 Finishing

A. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 32

B. Facing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

14 Appliance Setup

A. Remove Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 33

B. Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . . 33

C. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

D. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

E. Ember Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

F. Install the Log Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . 34

G. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

H. Install Trim and/or Surround . . . . . . . . . . . . . . . . . . . . . . . 36

I. Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

15 Troubleshooting

A. Standing Pilot Ignition System . . . . . . . . . . . . . . . . . . . . . 37

B. IntelliFire Ignition System . . . . . . . . . . . . . . . . . . . . . . . . . 39

16 Reference Materials

A. Appliance Dimension Diagram . . . . . . . . . . . . . . . . . . . . . 41

B. Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

C. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Î = Contains updated information.

Heat & Glo • 6000GBV, 6000GBV-IPI • 2104-900 Rev. i • 6/094

B. Limited Lifetime Warranty

Heat & Glo • 6000GBV, 6000GBV-IPI • 2104-900 Rev. i • 6/09 5

B. Limited Lifetime Warranty (continued)

Heat & Glo • 6000GBV, 6000GBV-IPI • 2104-900 Rev. i • 6/096

Listing and Code Approvals

A. Appliance Certiﬁ cation

MODELS: 6000GBV, 6000GBV-IPI, 6000GBV-LP, 6000GBV-IPILP

LABORATORY: Underwriters Laboratories, Inc. (UL) TYPE: B-Vent Gas Appliance STANDARD: ANSI Z21.50-2002•CGA2.2

This product is listed to ANSI standards for “Vented Gas Fireplaces” and “Gas Fired Appliances for Use at High Altitudes”.

May be installed in a sleeping room when the provisions for combustion, ventilation and dilution air are met per the requirements of ANSI 223.1/NFPA 54 National Fuel Gas Code. In Canada, installation in a sleeping room requires installation with a thermostat certiﬁ ed for use with this prod- uct. Consult your local authorities having jurisdiction.

NOTICE: This installation must conform with local codes. In the absence of local codes you must comply with the National Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A. and the CAN/CGA B149 Installation Codes in Canada.

NOT INTENDED FOR USE AS A PRIMAR Y HEAT SOURCE.

This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be factored as primary heat in residential heating calculations.

B. Tempered Glass Speciﬁ cations

Hearth & Home Technologies appliances manufactured with tempered glass may be installed in hazardous locations such as bathtub enclosures as deﬁ ned by the Con- sumer Product Safety Commission (CPSC). The tempered glass has been tested and certiﬁ ed to the requirements of ANSI Z97.1 and CPSC 16 CFR 1202 (Safety Glazing Certiﬁ cation Council SGCC# 1595 and 1597. Architectur- al Testing, Inc. Reports 02-31919.01 and 02-31917.01).

This statement is in compliance with CPSC 16 CFR Sec- tion 1201.5 “Certiﬁ cation and labeling requirements” which refers to 15 U.S. Code (USC) 2063 stating “…Such certiﬁ cate shall accompany the product or shall otherwise be furnished to any distributor or retailer to whom the product is delivered.”

Some local building codes require the use of tempered glass with permanent marking in such locations. Glass meeting this requirement is available from the factory. Please contact your dealer or distributor to order.

C. BTU Speciﬁ cations

U.S. (0-2000 ft.) or Canada (2000-4500 ft.)

6000GBV 6000GBV-IPI

6000GBV-LP 6000GBV-IPILP

Models

Maximum

Input BTUH

27,000 18,000 #40

CAN

24,300 16,200 #41

27,000 18,000 #53

CAN

24,300 16,200 #54

Minimum

Input BTUH

Oriﬁ ce

Size

(DMS)

D. High Altitude Installations

NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.

When installing above 2000 feet elevation:

• In the USA: Reduce input rate 4% for each 1000 feet above 2000 feet.

• In CANADA: Reduce input rate 10% for elevations between 2000 feet and 4500 feet. Above 4500 feet, consult local gas utility.

Check with your local gas utility to determine proper oriﬁ ce size.

E. Non-Combustible Materials Speciﬁ cation

Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750 ºC and UL763 shall be

considered non-combustible materials.

F. Combustible Materials Speciﬁ cation

Materials made of or surfaced with wood, compressed paper, plant ﬁ bers, plastics, or other material that can ignite and burn, whether ﬂ ame proofed or not, or plastered or unplastered shall be considered combustible materials.

G. Electrical Codes

NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA

70-latest edition or the Canadian Electric Code CSA C22.1.

• A 110-120 VAC circuit for this product must be pro-

tected with ground-fault circuit-interrupter protection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

Heat & Glo • 6000GBV, 6000GBV-IPI • 2104-900 Rev. i • 6/09 7

Operating Instructions

User Guide

A. Gas Fireplace Safety

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

• DO NOT touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as ﬁ replace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other ﬂ ammable materials.

• Keep clothing, furniture, draperies and other ﬂ ammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the ﬁ xed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

If you expect that small children or vulnerable adults may come into contact with this ﬁ replace, the following precau- tions are recommended:

• Install a physical barrier such as:

- A decorative ﬁ rescreen.

- Adjustable safety gate.

• Install a switch lock or a wall/remote control with child protection lockout feature.

• Keep remote controls out of reach of children.

• Never leave children alone near a hot ﬁ replace, whether operating or cooling down.

• Teach children to NEVER touch the ﬁ replace.

• Consider not using the ﬁ replace when children will be present.

Contact your dealer for more information, or visit: www. hpba.org/staysafe.

T o prevent unintended operation when not using your ﬁ re- place for an extended period of time (summer months, vacation, trips, etc):

• Remove batteries from remote controls.

• Turn off wall controls.

• Unplug 3 volt adapter plug and remove batteries on IPI models.

• Turn off gas controls valve on standing pilot models.

When lighting the pilot light on ﬁ replaces with a standing pilot, remove the ﬁ xed glass assembly so you can de- tect presence of residual gas build-up. See Standing Pilot Lighting instructions and Maintenance Tasks.

B. Your Fireplace

WARNING! DO NOT operate ﬁ replace before read- ing and understanding operating instructions. Failure

to operate ﬁ replace according to operating instructions could cause ﬁ re or injury.

Figure 2.1 General Operating Parts

DECORATIVE DOORS

(NOT SHOWN)

SECTION 2.E.

FIXED GLASS ASSEMBLY

(NOT SHOWN) SECTION 14.G.

OUTSIDE AIR CONTROL

(NOT SHOWN)

SECTION 2.H.

MANTEL

HEARTH

CLEAR SPACE

SECTION 2.D.

Heat & Glo • 6000GBV, 6000GBV-IPI • 2104-900 Rev. i • 6/098

C. Fan Kit (optional)

If desired, a fan kit may be added. Contact your dealer to order the correct fan kit.

D. Clear Space

WARNING! DO NOT place combustible objects in front of the ﬁ replace or block louvers. High temperatures may start a ﬁ re. See Figure 2.2.

A void placing candles and other heat-sensitive objects on mantel or hearth. Heat may damage these objects.

3 FT. IN FRONT OF FIREPLACE

CLEAR SPACE

Figure 2.2 Clear Space

E. Decorative Doors and Fronts

WARNING! Risk of Fire! Install ONLY doors or fronts approved by Hearth & Home Technologies. Unapproved doors or fronts may cause ﬁ replace to overheat.

This fireplace has been supplied with an integral barrier to prevent direct contact with the ﬁ xed glass panel. DO NOT operate the ﬁ replace with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

For more information refer to the instructions supplied with your decorative door or front.

For safety:

• Install a switch lock or a wall/remote control with child protection lockout feature.

• Keep remote controls out of reach of children.

See your dealer if you have questions.

H. Outside Air (optional)

The outside air kit supplies some fresh combustion air for your ﬁ replace. It may help reduce the effects of negative air pressure. (See Section 9.A.)

• Refer to Figure 9.2 for location of control.

• Close the inlet to prevent cold drafts when the ﬁ replace is not being used.

CAUTION! Risk of Burns! The outside air control handle is HOT when ﬁ replace is in operation. Adjust BEFORE lighting ﬁ re.

I. Before Lighting Fireplace

Before operating this ﬁ replace for the ﬁ rst time, have a qualiﬁ ed service technician:

• Verify all shipping materials have been removed from inside and/or underneath the ﬁ rebox.

• Review proper placement of logs, ember material and/or other decorative materials.

• Check the wiring.

• Check the air shutter adjustment.

• Ensure that there are no gas leaks.

• Ensure that the glass is sealed and in the proper position and that the integral barrier is in place.

WARNING! Risk of Fire/Asphyxiation! DO NOT operate ﬁ replace with ﬁ xed glass assembly removed.

Determine if this ﬁ replace has a standing pilot or an IntelliFire ignition system. Ask your dealer or open control access panel, look at gas valve assembly.

• A standing pilot ignition will have a red or black ignitor button (refer to Figure 2.3).

• An IntelliFire ignition system will not have a button.

RED OR BLACK BUTTON

F. Fixed Glass Assembly

See Section 14.G.

G. Remote Controls, Wall Controls and Wall

Switches

Follow the instructions supplied with the control installed to operate your ﬁ replace:

Heat & Glo • 6000GBV, 6000GBV-IPI • 2104-900 Rev. i • 6/09 9

Figure 2.3 Ignitor Button

J. Lighting Instructions (IPI)

The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer. To prolong battery life, remove them when using the transformer.

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a ﬁ re or explosion

may result causing property damage, personal injury or loss of life.

A. This appliance is equipped with an

intermittent pilot ignition (IPI) device which automatically lights the burner. DO NOT try to light the burner by hand.

B. BEFORE LIGHTING, smell all around

the appliance area for gas. Be sure to smell next to the ﬂ oor because some gas is heavier than air and will settle on the ﬂ oor.

WHA T TO DO IF YOU SMELL GAS

• DO NOT try to light any appliance.

• DO NOT touch any electric switch; do not use any phone in your building.

WARNING:

DO NOT CONNECT 110 VAC TO THE CONTROL VALVE.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or fuel combustion which are known to the State of California to cause cancer, birth defects, or other reproductive harm.

Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁ re department.

C. DO NOT use this appliance if any

part has been under water. Immediately call a qualiﬁ ed service tech- nician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

CAUTION:

Hot while in operation. DO NOT touch. Keep children, clothing, furniture, gasoline and other liquids having ﬂ ammable vapors away.

DO NOT operate the appliance with ﬁ xed glass assembly removed, cracked or broken. Replacement of the ﬁ xed glass assembly should be done by a licensed or qualiﬁ ed service person.

NOT FOR USE

WITH SOLID FUEL

For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.

Also Certiﬁ ed for Installation in a Bedroom or a Bedsitting Room.

For assistance or additional information, consult a qualiﬁ ed installer, ser- vice agency or the gas supplier.

LIGHTING

INSTRUCTIONS

(IPI)

1. Turn off all electric power to the appliance.

2. This appliance is equipped with an ignition

device which automatically lights the burner.

DO NOT try to light the burner by hand.

GAS

VALVE

3. Wait ﬁ ve (5) minutes to clear out any gas.

Then smell for gas, including near the ﬂ oor. If you smell gas, STOP! Follow “B” in the Safety Information located on the left side of this label. If you do not smell gas, go to next step.

4. Turn on all electric power to the appliance.

5. To light the burner, ﬂ ip the ON/OFF switch to

the “ON” position. (The ON/OFF switch may include a wall switch if so equipped).

6. If the appliance will not operate, follow the instructions “To Turn Off Gas to Appliance” and call your service technician or gas supplier.

TO TURN OFF

GAS TO APPLIANCE

1. Turn wall control or ON/OFF switch to “OFF”.

2. Turn off all electric power to the appliance if

service is to be performed.

593-913F

Hearth & Home Technologies ﬁ replace, please refer to www.ﬁ replaces.com.

For additional information on operating your

Final inspection by

Heat & Glo • 6000GBV, 6000GBV-IPI • 2104-900 Rev. i • 6/0910

K. Lighting Instructions (Standing Pilot)

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a ﬁ re or explosion

may result causing property damage, personal injury or loss of life.

A. This appliance has a pilot which

must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B. BEFORE LIGHTING, smell all around

the appliance area for gas. Be sure to smell next to the ﬂ oor because some gas is heavier than air and will settle on the ﬂ oor.

WHA T TO DO IF YOU SMELL GAS

• DO NOT try to light any appliance.

• DO NOT touch any electric switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

WARNING:

DO NOT CONNECT 110 VAC TO THE CONTROL VALVE.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

For additional information on operating your

Hearth & Home Technologies ﬁ replace, please refer to www.ﬁ replaces.com.

• If you cannot reach your gas supplier, call the ﬁ re department.

C. Use only your hand to push in or

turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, DO NOT try to repair it, call a qualiﬁ ed service technician. Force or attempted repair may result in a ﬁ re or explosion.

D. DO NOT use this appliance if any

part has been under water. Immediately call a qualiﬁ ed service tech- nician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

CAUTION:

Hot while in operation. DO NOT touch. Keep children, clothing, furniture, gasoline and other liquids having ﬂ ammable vapors away.

DO NOT operate the appliance with ﬁ xed glass assembly removed, cracked or broken. Replacement of the ﬁ xed glass assembly should be done by a licensed or qualiﬁ ed service person.

NOT FOR USE

WITH SOLID FUEL

For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.

Also Certiﬁ ed for Installation in a Bedroom or a Bedsitting Room.

For assistance or additional information, consult a qualiﬁ ed installer, ser- vice agency or the gas supplier.

Final inspection by

1. Open control access panel.

2. Turn off all electric power to

3. Push in gas control knob

Note: Knob cannot be turned from “PILOT” to “OFF” unless knob is pushed in slightly. DO NOT force.

4. Open the ﬁ xed glass assembly. You may need to

5. Wait ﬁ ve (5) minutes to clear out any gas. Then

6. Find the pilot. The pilot is inside

7. Turn knob on gas control counterclockwise

8. Push in control knob all the way and hold in. Immedi-

9. Reinstall ﬁ xed glass assembly. Reinstall decorative

10. Turn gas control knob counterclockwise

11. Turn on all electric power to the appliance.

12. To light burner, turn the wall control or on/off switch

1. Turn off all electric power to the appliance if ser-

2. Open control access panel.

3. Move switch to “OFF” position.

4. Push in gas control knob slightly and turn clock-

5. Close control access panel.

LIGHTING

INSTRUCTIONS

the appliance.

slightly and turn clockwise

to “OFF”.

remove the decorative front.

smell for gas, including near the ﬂ oor. If you smell gas, STOP! Follow “B” in the Safety Information located on the left side of this label. If you don’t smell gas, go to next step.

combustion chamber next to the main burner

to “PILOT”.

ately depress red or black piezo button. It may require several depressions of the red or black piezo button until PILOT lights. If PILOT light does not light after 10 seconds, return to step 3. Continue to hold the control knob in for about one minute after the pilot is lit. Release knob and it will pop back out. Pilot should remain lit. If it goes out, repeat steps 3 through 6.

• If knob does not pop up when released, stop and immediately call your service technician or gas supplier.

• If the pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call your service technician or gas supplier.

front.

to “ON”. Close access panel.

to “ON”.

TO TURN OFF

GAS TO APPLIANCE

vice is to be performed.

wise to OFF”. DO NOT force.

464-903H

Heat & Glo • 6000GBV, 6000GBV-IPI • 2104-900 Rev. i • 6/09 11

L. After Fireplace is Lit

Initial Break-in Procedure

• The fireplace should be run three to four hours continuously on high.

• Turn the ﬁ replace off and allow it to completely cool.

• Remove ﬁ xed glass assembly. See Section 14.G.

• Clean ﬁ xed glass assembly. See Section 3.

• Replace the ﬁ xed glass assembly and run continuously on high an additional 12 hours.

This cures the materials used to manufacture the ﬁ re- place.

NOTICE! Open windows for air circulation during ﬁ re- place break-in.

• Some people may be sensitive to smoke and odors.

• Smoke detectors may activate.

M. Frequently Asked Questions

ISSUE SOLUTIONS

Condensation on the glass

Blue ﬂ ames

Odor from appliance

Film on the glass

Metallic noise

Is it normal to see the pilot ﬂ ame burn continually?

This is a result of gas combustion and temperature variations. As the appliance warms, this condensation will disappear.

This is a result of normal operation and the ﬂ ames will begin to yellow as the appliance is al- lowed to burn for 20 to 40 minutes.

When ﬁ rst operated, this appliance may release an odor for the ﬁ rst several hours. This is caused by the curing of the paint and the burning off of any oils remaining from manufacturing. Odor may also be released from ﬁ nishing materials and adhesives used around the appliance.

This is a normal result of the curing process of the paint and logs. Glass should be cleaned within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing process. A non-abrasive cleaner such as gas ﬁ replace glass cleaner may be necessary. See your dealer.

Noise is caused by metal expanding and contracting as it heats up and cools down, similar to the sound produced by a furnace or heating duct. This noise does not affect the operation or longevity of the appliance.

In an Intelliﬁ re ignition system it is normal to see the pilot ﬂ ame, but it should turn off when ON/OFF is turned off. In a standing pilot system the pilot will always stay on.

Heat & Glo • 6000GBV, 6000GBV-IPI • 2104-900 Rev. i • 6/0912

Maintenance and Service

Any safety screen or guard removed for servicing must be replaced prior to operating the ﬁ replace.

When properly maintained, your ﬁ replace will give you many years of trouble-free service. We recommend annual service by a qualiﬁ ed service technician.

A. Maintenance Tasks-Homeowner

Installation and repair should be done by a qualiﬁ ed service technician only. The ﬁ replace should be inspected before use and at least annually by a professional service person.

The following tasks may be performed annually by the homeowner. If you are uncomfortable performing any of the listed tasks, please call your dealer for a service appointment.

More frequent cleaning may be required due to lint from carpeting or other factors. Control compartment, burner and circulating air passageway of the ﬁ replace must be kept clean.

CAUTION! Risk of Burns! The ﬁ replace should be turned off and cooled before servicing.

Glass Cleaning

Frequency: Seasonally By: Homeowner Tools Needed: Protective gloves, glass cleaner, drop

cloth and a stable work surface.

CAUTION! Handle ﬁ xed glass assembly with care.

Glass is breakable.

• Avoid striking, scratching or slamming glass

• Avoid abrasive cleaners

• DO NOT clean glass while it is hot

• Prepare a work area large enough to accommodate ﬁ xed glass assembly and door frame by placing a drop cloth on a ﬂ at, stable surface.

Note: Fixed glass assembly and gasketing may have residue that can stain carpeting or ﬂ oor surfaces.

• Remove door or decorative front from ﬁ replace and set aside on work surface.

• See Section 14.G for instructions to remove ﬁ xed glass assembly.

• Clean glass with a non-abrasive commercially available cleaner.

- Light deposits: Use a soft cloth with soap and water

- Heavy deposits: Use commercial fireplace glass

cleaner (consult with your dealer)

• Carefully set ﬁ xed glass assembly in place on ﬁ replace. Hold glass in place with one hand and secure glass latches with the other hand.

• Reinstall door or decorative front.

Heat & Glo • 6000GBV, 6000GBV-IPI • 2104-900 Rev. i • 6/09 13

Doors, Surrounds, Fronts

Frequency: Annually By: Homeowner Tools needed: Protective gloves, stable work surface

• Assess condition of screen and replace as necessary.

• Inspect for scratches, dents or other damage and repair as necessary.

• Check that louvers are not blocked.

• Vacuum and dust surfaces.

Remote Control

Frequency: Seasonally By: Homeowner Tools needed: Replacement batteries and remote con-

trol instructions.

• Locate remote control transmitter and receiver.

• Verify operation of remote. Refer to remote control operation instructions for proper calibration and setup procedure.

• Place batteries as needed in remote transmitters and battery-powered receivers.

• Place remote control out of reach of children.

If not using your ﬁ replace for an extended period of time (summer months, vacations/trips, etc), to prevent unintended operation:

• Remove batteries from remote controls.

• Unplug 3 volt adapter plug on IPI models.

Venting

Frequency: Seasonally By: Homeowner Tools needed: Protective gloves and safety glasses.

• Inspect venting and termination cap for blockage or obstruction such plants, bird nests, leaves, snow, debris, etc.

• Verify termination cap clearance to subsequent construction. See Section 6.

• Inspect for corrosion or separation.

• Verify weather stripping, sealing and ﬂ ashing remains intact.

• Inspect draft shield to verify it is not damaged or missing.

B. Maintenance Tasks-Qualiﬁ ed Service

Technician

The following tasks must be performed by a qualiﬁ ed ser- vice technician.

Gasket Seal and Glass Assembly Inspection

Frequency: Annually By: Qualiﬁ ed Service Technician T ools needed: Protective gloves, drop cloth and a stable

work surface.

• Inspect gasket seal and its condition.

• Inspect ﬁ xed glass assembly for scratches and nicks that can lead to breakage when exposed to heat.

• Conﬁ rm there is no damage to glass or glass frame. Replace as necessary.

• Verify that ﬁ xed glass assembly is properly retained and attachment components are intact and not damaged. Replace as necessary.

Logs

Frequency: Annually By: Qualiﬁ ed Service Technician Tools needed: Protective gloves.

• Inspect for damaged or missing logs. Replace as necessary. Refer to Section 14 for log placement instructions.

• Verify correct log placement and no ﬂ ame impingement causing sooting. Correct as necessary.

Firebox

Frequency: Annually By: Qualiﬁ ed Service Technician Tools needed: Protective gloves, sandpaper, steel wool,

cloths, mineral spirits, primer and touch-up paint.

• Inspect for paint condition, warped surfaces, corrosion or perforation. Sand and repaint as necessary.

• Replace ﬁ replace if ﬁ rebox has been perforated.

Frequency: Annually By: Qualiﬁ ed Service Technician Tools needed: Protective gloves, vacuum cleaner, dust

cloths

• V acuum and wipe out dust, cobwebs, debris or pet hair. Use caution when cleaning these areas. Screw tips that have penetrated the sheet metal are sharp and should be avoided.

• Remove all foreign objects.

• Verify unobstructed air circulation.

Burner Ignition and Operation

Frequency: Annually By: Qualiﬁ ed Service Technician T ools needed: Protective gloves, vacuum cleaner, whisk

broom, ﬂ ashlight, voltmeter, indexed drill bit set, and a manometer.

• Verify burner is properly secured and aligned with pilot or igniter.

• Clean off burner top, inspect for plugged ports, corrosion or deterioration. Replace burner if necessary.

• Replace Glowing embers with new dime-size pieces. DO NOT block ports or obstruct lighting paths. Refer to Section 14 for proper ember placement.

• Verify batteries have been removed from battery backup IPI systems to prevent premature battery failure or leaking.

• Check for smooth lighting and ignition carryover to all ports. Verify that there is no ignition delay.

• Inspect for lifting or other ﬂ ame problems.

• Verify air shutter setting is correct. See Section 14 for required air shutter setting. Verify air shutter is clear of dust and debris.

• Inspect oriﬁ ce for soot, dirt and corrosion. Verify oriﬁ ce size is correct. See Service Parts List for proper oriﬁ ce sizing.

• Verify manifold and inlet pressures. Adjust regulator as required.

• Inspect pilot ﬂ ame pattern and strength. See Figures 3.1 and 3.2 for proper pilot ﬂ ame pattern. Clean or replace oriﬁ ce spud as necessary.

• Inspect thermocouple/thermopile or IPI ﬂ ame sensing rod for soot, corrosion and deterioration. Clean with emery cloth or replace as required.

• Verify thermocouple/thermopile millivolt output. Replace pilot as necessary (Standing pilot only).

• Verify that there is not a short in ﬂ ame sense circuit by checking continuity between pilot hood and ﬂ ame sense rod. Replace pilot as necessary (IPI only).

Control Compartment and Firebox Top

Heat & Glo • 6000GBV, 6000GBV-IPI • 2104-900 Rev. i • 6/0914

+ 32 hidden pages