Heat Glo 6000CL-IFT-S, 6000CL-IFTLP-S, 6000CL-IFT-G, 6000CL-IFTLP-G, 8000CL-IFT-S Installation Manual

...

Installation Manual

Installation and Appliance Setup

INSTALLER: Leave this manual with party responsible for use and operation. OWNER: Retain this manual for future reference.

NOTICE: DO NOT discard this manual!

Models:

6000CL-IFT-S 6000CL-IFTLP-S 6000CL-IFT-G 6000CL-IFTLP-G 8000CL-IFT-S 8000CL-IFTLP-S 8000CL-IFT-G 8000CL-IFTLP-G

WARNING: FIRE OR EXPLOSION HAZARD Failure to follow safety warnings exactly could result in serious injury, death, or property damage.

• DO NOT store or use gasoline or other am- mable vapors and liquids in the vicinity of this

or any other appliance.

• What to do if you smell gas

- DO NOT try to light any appliance.

- DO NOT touch any electrical switch. DO

NOT use any phone in your building.

- Leave the building immediately.

- Immediately call your gas supplier from

a neighbor’s phone. Follow the gas sup-

plier’s instructions.

- If you cannot reach your gas supplier, call

the re department.

• Installation and service must be performed

by a qualied installer, service agency, or the gas supplier.

This appliance may be installed as an OEM installation in manufactured home (USA only) or mobile home and must be installed in accordance with the manufacturer’s instructions and the Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280 in the United States, or the Standard for Installation in Mobile Homes, CAN/CSA Z240 MH Series, in Canada.

This appliance is only for use with the type(s)

of gas indicated on the rating plate. This

appliance is not convertible for use with other

gases, unless a certied kit is used.

In the Commonwealth of Massachusetts installation must be

performed by a licensed plumber or gas tter.

See T able of Contents for location of additional Commonwealth

of Massachusetts requirements.

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/21

DANGER

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

A barrier designed to reduce the risk of

burns from the hot viewing glass is provided with this appliance and must be installed for

the protection of children and other at-risk individuals.

Safety Alert Key:

• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.

• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• NOTICE: Used to address practices not related to personal injury. Note: The term “recommend” or “recommended” does not indicate a requirement. It is a best practice suggested by Hearth

& Home Technologies®. Failure to perform the recommended task will not result in a safety concern.

Table of Contents

Installation Standard Work Checklist ....................3

1 Product Specic and Important Safety Information

A. Appliance Certication ............................4

B. Glass Specications ..............................4

C. BTU Specications ............................... 4

D. High Altitude Installations ..........................4

E. Non-Combustible Materials Specication. . . . . . . . . . . . . . 4

F. Combustible Materials Specication .................4

G. Electrical Codes .................................4

H. California ...................................... 4

I. Requirements for the Commonwealth of Massachusetts . . 5

2 Getting Started

A. Design and Installation Considerations ............... 6

B. Good Faith Wall Surface

C. Tools and Supplies Needed ........................6

D. Inspect Appliance and Components ..................7

..........................6

3 Framing and Clearances

A. Appliance/Decorative Front Dimension Diagrams .......8

B. Clearances to Combustibles ......................14

C. Constructing the Appliance Chase ..................16

4 Termination Location and Vent Information

A. Vent Termination Minimum Clearances .............. 17

B. Vent Terminal Clearances

C. Approved Pipe .................................19

D. Use of Elbows .................................20

E. Measuring Standards ............................ 21

F. Vent Diagrams ................................. 22

........................18

5 Vent Clearances and Framing

A. Pipe Clearances to Combustibles .................. 34

B. Wall Penetration Framing/Firestops .................35

C. Ceiling Firestop/Floor Penetration Framing ...........36

D. Install Attic Insulation Shield .......................36

7 Venting and Chimneys

A. Assemble Vent Sections (DVP Pipe Only) ............41

B . Assemble Vent Sections (SLP Only) ................ 42

C. Assemble Slip Sections ..........................42

D. Secure the Vent Sections ......................... 43

E. Disassemble Vent Sections ....................... 43

F. Vertical Termination Requirements ..................44

G. Horizontal Termination Requirements ...............45

8 Electrical Information

A. General Information .............................47

B. Wiring Requirements ............................49

9 Gas Information

A. Fuel Conversion ................................ 51

B. Gas Pressure ..................................51

C. Gas Connection ................................51

D. High Altitude Installations .........................51

E. Air Shutter Setting .............................. 52

10 Finishing

A. Facing Material .................................53

B. Mantel and Wall Projections ....................... 54

C. Decorative Fronts ............................... 55

11 Appliance Setup

A. Remove Fixed Glass Assembly ....................58

B. Remove the Shipping Materials ....................58

C. Clean the Appliance .............................58

D. Burner Top Installation ...........................58

E. Install the Fiber Refractory ....................... 59

F. Black Glass Refractory Installation .................61

G. Ember Placement ............................... 62

H. Install the Log Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . 63

I. IntelliFire Touch

J. Install Fixed Glass Assembly ......................67

K. Install Decorative Front ..........................67

Control System Setup ..............67



6 Appliance Preparation

A. Vent Collar Preparation ..........................37

B. Installing Optional Heat Management Systems ........39

C. Securing and Leveling the Appliance ................40

D. Installing the Non-combustible Board. . . . . . . . . . . . . . . . 40

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/212

12 Reference Materials

A. Vent Components Diagrams ......................68

B. Accessories ................................... 79

 = Contains updated information.

Installation Standard Work Checklist

ATTENTION INSTALLER:

Follow this Standard Work Checklist

This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this

installation manual.

Customer: Lot/Address:

Model (circle one): 6000CL-IFT 6000CL-IFTLP 8000CL-IFT 8000CL-IFTLP

WARNING! Risk of Fire or Explosion! Failure to install appliance according to these instructions could

lead to a re or explosion.

Appliance Install YES IF NO, WHY?

Veried that the chase is insulated and sealed. (Pg. 16) ___________________________ Required non-combustible board is installed. (Pg. 40) ___________________________ Veried clearances to combustibles. (Pg. 14-15) ___________________________

Fireplace is leveled and secured. (Pg. 40) ___________________________

Venting/Chimney Section 7 (Pg 41-46)

Venting conguration complies to vent diagrams. ___________________________ Venting installed, locked and secured in place with proper clearance. ___________________________ Elbow heat shield installed per requirements. (Pg 23, 34) ___________________________

Firestops installed. ___________________________ Attic insulation shield installed. ___________________________

Exterior wall/Roof ashing installed and sealed. ___________________________

Terminations installed and sealed. ___________________________

Date Installed: Location of Fireplace: Installer: Dealer/Distributor Phone #

Serial #:

Electrical Section 8 (Pg 47-50)

Unswitched power (110-120 VAC) provided to the appliance. ___________________________ Switch wires properly installed. ___________________________

Gas Section 9 (Pg 51-52)

Proper appliance for fuel type. ___________________________

Was a conversion performed? ___________________________

Leak check performed and inlet pressure veried. ___________________________

Veried proper air shutter setting for installation type. ___________________________

Finishing Section 10 (Pg 53-57) Combustible materials not installed in non-combustible areas. ___________________________

Veried all clearances meet installation manual requirements. ___________________________

Mantels and wall projections comply with installation manual requirements. ___________________________

Appliance Setup Section 11 (Pg 58-67)

All packaging and protective materials removed (inside & outside of appliance). ___________________________ Refractories, logs, and embers installed correctly. ___________________________

Glass assembly installed and secured. ___________________________ Accessories installed properly. ___________________________ Decorative front properly installed. ___________________________

Manual bag and all of its contents are removed from inside/under the appliance and given to party responsible for use and operation. ___________________________

Started appliance and veried no gas leaks exist. ___________________________

Hearth & Home Technologies recommends the following:

• Photographing the installation and copying this checklist for your le.

• That this checklist remain visible at all times on the appliance until the installation is complete.

Comments: Further description of the issues, who is responsible (Installer/ Builder/ Other Trades, etc) and corrective action needed _____________________________________________________________________________________ _________________________________________________________________________________________________ _________________________________________________________________________________________________ Comments Communicated to party responsible ____________________ by ______________________on ___________ (Builder / Gen. Contractor/) (Installer) (Date)

 = Contains updated information.

2504-982 Rev. B 5/18

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/21

1 1

Product Specic and Important Safety Information

A. Appliance Certication

MODELS: 6000CL-IFT-S, 6000CL-IFTLP-S, 6000CL-IFT-G, 6000CL-IFTLP-G, 8000CL-IFT-S, 8000CL-IFTLP-S, 8000CL-IFT-G, 8000CL-IFTLP-G

LABORATORY: Underwriters Laboratories, Inc. (UL) TYPE: Direct Vent Heater STANDARD: CSA / ANSI Z21.88:19 • CSA 2.33:19

This product is listed to ANSI standards for “Vented Gas

Fireplace Heaters” and applicable sections of “Gas Burn-

ing Heating Appliances for Manufactured Homes and

Recreational Vehicles”, and “Gas Fired Appliances for Use at High Altitudes”.

NOTICE: This installation must conform with local codes. In the absence of local codes you must comply with the National Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A. and the CAN/CGA B149 Installation Codes in Canada.

NOT INTENDED FOR USE AS A PRIMAR Y HEAT SOURCE.

This appliance is tested and approved as either supplemen-

tal room heat or as a decorative appliance. It should not be factored as primary heat in residential heating calculations.

B. Glass Specications

This appliance is equipped with 5 mm ceramic glass. Re-

place glass only with 5 mm ceramic glass. Please contact your dealer for replacement glass.

C. BTU Specications

Models

(U.S. or Canada)

6000CL-IFT

(NG)

6000CL-IFTLP

(Propane)

8000CL-IFT

(NG)

8000CL-IFTLP

(Propane)

Maximum

Input

BTU/h

(0-2000 FT) 35,000 18,000 #33

(0-2000 FT) 34,000 20,000 #51

(0-2000 FT) 40,000 20,000 #31

(0-2000 FT) 40,000 23,000 #49

Minimum

Input BTU/h

Orice

Size

(DMS)

D. High Altitude Installations

NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.

When installing above 2000 feet elevation:

• In the USA: Reduce input rate 4% for each 1000 feet

above 2000 feet.

• In CANADA: Input ratings are certied without a

reduction of input rate for elevations up to 4500 feet

(1370 m) above sea level. Please consult provincial and/ or local authorities having jurisdiction for installations at elevations above 4500 feet (1370 m).

Check with your local gas utility to determine proper orice size.

E. Non-Combustible Materials Specication

Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136, Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750 ºC shall be considered

non-combustible materials.

F. Combustible Materials Specication

Materials made of or surfaced with wood, compressed pa-

per, plant bers, plastics, or other material that can ignite and burn, whether ame proofed or not, or plastered or unplastered shall be considered combustible materials.

G. Electrical Codes

NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code

ANSI/NFPA 70-latest edition or the Canadian Electric Code CSA C22.1.

• A 110-120 VAC circuit for this product must be pro-

tected with ground-fault circuit-interrupter protection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms

or near sinks.

H. California

WARNING: This product and the fuels used to

operate this product (liquid propane or natural

gas), and the products of combustion of such fuels, can

expose you to chemicals including benzene, which is known to the State of California to cause cancer and reproductive harm. For more information go to: www. P65Warnings.ca.gov.

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/214

Note: The following requirements reference various Massachuset ts and national codes n ot contained in this

document.

I. Requirements for the Commonwealth of

Massachusetts

For all side wall horizontally vented gas fueled equipment

installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the

side wall exhaust vent termination is less than seven (7)

feet above nished grade in the area of the venting, in-

cluding but not limited to decks and porches, the following requirements shall be satised:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gas tter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the oor

level where the gas equipment is to be installed. In addi-

tion, the installing plumber or gas tter shall observe that

a battery operated or hard wired carbon monoxide detec-

tor with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall

horizontal vented gas fueled equipment. It shall be the

responsibility of the property owner to secure the services

of qualied licensed professionals for the installation of hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fu-

eled equipment is installed in a crawl space or an attic,

the hard wired carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent oor level.

In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon

monoxide detector with an alarm shall be installed.

Inspection

The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector ob-

serves carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.

Exemptions

The following equipment is exempt from 248 CMR 5.08(2)

(a)1 through 4:

• The equipment listed in Chapter 10 entitled “Equipment

Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the Board; and

• Product Approved side wall horizontally vented gas fu-

eled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or

in part for residential purposes.

MANUFACTURER REQUIREMENTS Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting

system design or venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

• Detailed instructions for the installation of the venting

system design or the venting system components; and

• A complete parts list for the venting system design or

venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall

horizontally vented gas fueled equipment does not pro-

vide the parts for venting the ue gases, but identies “special venting systems”, the following requirements shall be satised by the manufacturer:

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accor-

dance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certied.

Signage

A metal or plastic identication plate shall be permanent-

ly mounted to the exterior of the building at a minimum

height of eight (8) feet above grade directly in line with the

exhaust vent terminal for the horizontally vented gas fu-

eled heating appliance or equipment. The sign shall read,

in print size no less than one-half (1/2) in. in size, “GAS

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/21

• The referenced “special venting system” instructions

shall be included with the appliance or equipment installation instructions; and

• The “special venting systems” shall be Product Ap-

proved by the Board, and the instructions for that system shall include a parts list and detailed installation

instructions.

A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equip-

ment, all venting instructions, all parts lists for venting

instructions, and/or all venting design instructions shall

remain with the appliance or equipment at the completion

of the installation.

See Gas Connection section for additional Commonwealth of Massachusetts requirements.

2 2

Getting Started

A. Design and Installation Considerations

Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of

the building and all exhaust gases expelled to the outside. No additional outside air source is required.

Installation MUST comply with local, regional, state and

national codes and regulations. Consult insurance carrier, local building inspector, re o󰀩cials or authorities having jurisdiction over restrictions, installation inspection and permits.

Before installing, determine the following:

• Where the appliance is to be installed.

• The vent system conguration to be used.

• Gas supply piping requirements.

• Provisions for optional heat management system.

• Electrical wiring requirements.

• Framing and nishing details.

• Whether optional accessories—devices such as a fan,

wall switch, or remote control—are desired.

B. Good Faith Wall Surface

FIREPLACE

OPENING

135°F

147°F

6 in.

Figure 2.1 Good Faith Wall Surface Temperatures Above Appliance

If installing a television (TV) above the appliance, see Section 3 of the appliance Owner’s Manual.

TO CEILING

127°F

123°F

132°F

12 in.

TOP EDGE OF THE OPENING

APPLIANCE FRONT

30 in.

24 in.

18 in.

MEASUREMENTS FROM

Installation and service of this appliance should be performed by

qualied personnel. Hearth & Home Technologies recommends HHT Factory Trained or NFI certied professionals.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. For assistance or additional information, consult a qualied service technician, service agency or your dealer.

NOTICE: Temperatures listed above are taken with a temperature measuring probe as prescribed by the test

standard used for appliance certication. Temperatures

on walls or mantels taken with an infrared thermometer may yield increased temperatures of up to 30 degrees or more depending on the thermometer settings and material

characteristics being measured. Use appropriate nishing

materials that are able to withstand these conditions. For

additional nishing guidelines, see Section 10.

C. Tools and Supplies Needed

Before beginning the installation be sure that the following

tools and building supplies are available.

Tape measure Framing material

Pliers Hammer

Phillips screwdriver Manometer

Gloves Framing square

Voltmeter Electric drill and bits (1/4 in.)

Plumb line Safety glasses

Level Reciprocating saw

Flat blade screwdriver

Non-corrosive leak check solution

1/2 - 3/4 in. length, #6 or #8 Self-drilling screws

Caulking material (300 ºF minimum continuous exposure

rating)

One 1/4 in. female connection (for optional fan).

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/216

D. Inspect Appliance and Components

• Carefully remove the appliance and components from

the packaging.

• The vent system components and decorative doors and

fronts may be shipped in separate packages.

• If packaged separately, the log set and appliance grate must be installed.

• Report to your dealer any parts damaged in shipment,

particularly the condition of the glass.

• This product is factory-equipped with an IntelliFire Touch

remote control which was paired to the appliance at the

factory. This specic remote control needs to remain with the contents of the manual bag. Do not install batteries in the remote control until performing the nal appliance setup and checklist.

• Read all of the instructions before starting the installation. Follow these instructions carefully during the

installation to ensure maximum safety and benet.

WARNING! Risk of Fire or Explosion! Damaged parts could impair safe operation. DO NOT install damaged, incomplete or substitute components. Keep appliance dry.

Hearth & Home T echnologies disclaims any responsibility for , and the warranty will be voided by, the following actions:

• Installation and use of any damaged appliance or vent

system component.

• Modication of the appliance or vent system.

• Installation other than as instructed by Hearth & Home

Technologies.

• Improper positioning of the gas logs or the glass assembly.

• Installation and/or use of any component part not approved

by Hearth & Home Technologies.

Any such action may cause a re hazard.

WARNING! Risk of Fire, Explosion or Electric Shock! DO NOT use this appliance if any part has been under

water. Call a qualied service technician to inspect the

appliance and to replace any part of the control system and/or gas control which has been under water.

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/21

3 3

Framing and Clearances

A. Appliance/Decorative Front Dimension Diagrams

Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5.

HEAT MANAGEMENT SYSTEMS ACCESS (LEFT & RIGHT SIDES)

GAS LINE

ACCESS

LEFT SIDE RIGHT SIDE

Appliance Dimensions Table

Location Inches Millimeters

A 41 1041 B 36-1/8 918 C 33-1/2 851 D 34-5/8 879 E 2-1/4 57

F 9-11/16 246 G 26-7/8 683 H 6 dia. 152

I 39-7/8 1013

J 21 533

TOP VIEW

ELECTRICAL

ACCESS

(C)

B A

FRONT VIEW

Location Inches Millimeters

K 11-11/16 297

L 28-1/2 724 M 14-1/4 362 N 8-1/2 216 O 2-7/8 73

P 8-1/2 216 Q 1 25 R 40-7/8 1038

S 14-3/16 360

T 15-3/8 391

Figure 3.1 Appliance Dimensions - 6000CL-IFT Models

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/218

HEAT MANAGEMENT SYSTEMS ACCESS (LEFT & RIGHT SIDES)

GAS LINE

ACCESS

TOP VIEW

ELECTRICAL

ACCESS

(C)

LEFT SIDE

Appliance Dimensions Table

Location Inches Millimeters

A 48 1219 B 43-1/8 1096 C 35-1/2 902 D 36-5/8 930 E 2-3/8 60 F 9-15/16 252 G 28-7/8 734 H 6 152

I 41-7/8 1064

J 21 533

B A

FRONT VIEW

Location Inches Millimeters

K 11-11/16 297

L 35-1/2 901 M 17-3/4 451 N 8-1/2 216 O 2-7/8 73

P 8-1/2 216 Q 1 25 R 42-7/8 1089

S 14-1/16 357

T 17-1/16 433

RIGHT VIEW

Figure 3.2 Appliance Dimensions - 8000CL-IFT Models

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/21

FOLIO DECORATIVE FRONTS

A B C D E F G

6000 FOL-36

8000 FOL-42

in. 32-7/16 23-1/8 35-13/16 1-1/2 8-1/4 32-1/8 33-9/16

mm 824 587 910 38 210 816 853

in. 39-7/16 25-5/16 42-13/16 1-1/2 8-1/4 34-1/8 35-11/16

mm 1002 643 1087 38 210 867 907

C D

ARCADIA DECORATIVE FRONTS

A B C D E F G

6000 ARC-36

8000 ARC-42

in. 32-7/16 20-1/2 37-1/4 1-1/4 7-11/16 32-7/8 34-1/8

mm 824 521 946 32 195 835 867

in. 39-7/16 22-7/16 44-1/4 1-1/4 7-11/16 34-13/16 36-1/16

mm 1002 570 1124 32 195 884 916

Figure 3.3 Decorative Front Dimensions - Folio and Arcadia

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/2110

HALSTON DECORATIVE FRONTS

A B C D E F G

6000 HAL-36

8000 HAL-42

in. 32-7/16 21-1/4 37-1/4 1-1/4 7-1/4 32-7/8 34-1/8

mm 824 540 946 32 184 835 867

in. 39-7/16 23-1/8 44-1/4 1-1/4 7-1/4 34-13/16 36-1/16

mm 1002 587 1124 32 184 884 916

CHATEAU DECORATIVE FRONTS

A B C D E F G

6000 CHA-36

8000 CHA-42

Figure 3.4 Decorative Front Dimensions - Halston and Chateau

in. 20-1/2 32-7/16 37-1/4 1-1/2 7-7/8 32-7/8 34-1/8

mm 521 824 946 38 200 835 867

in. 22-7/16 39-7/16 44-1/8 1-1/4 7-7/8 34-13/16 36-1/16

mm 570 1002 1121 32 200 884 916

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/21

CHATEAU FORGE DECORATIVE FRONTS

A B C D E F G

6000 CHAF-36

8000 CHAF-42

in. 32-1/4 20-3/4 37 1-3/16 7-9/16 32-7/8 34-1/8

mm 819 527 940 30 192 835 867

in. 39-1/4 22-5/8 44 1-1/4 7-5/8 34-3/4 36

mm 997 575 1118 32 194 883 914

GALLERIA DECORATIVE FRONTS

C D

A B C D E F G

6000 GALLERIA-6

8000 GALLERIA-8

Figure 3.5 Decorative Front Dimensions - Chateau Forge and Galleria

in. 31-9/16 20-7/8 37-1/8 1-1/4 7-1/2 32-7/8 34-1/16

mm 802 530 943 32 191 835 865

in. 38-9/16 22-3/4 44-1/16 1-1/4 7-1/2 34-3/4 36

mm 979 578 1121 32 191 883 914

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/2112

CLEAN FACE DECORATIVE FRONTS

A B C D E F G

6000 CF-36

8000 CF-42

in. 31-9/16 22-1/8 35-13/16 3-1/2 4-9/16 26-13/16 28-15/16

mm 802 562 910 89 116 681 735

in. 38-1/2 24-1/16 42-3/4 3-1/2 4-9/16 28-11/16 30-13/16

mm 978 611 1086 89 116 729 783

IRON AGE DECORATIVE FRONTS

A B C D E F G

6000 FSI-36

8000 FSI-42

Figure 3.6 Decorative Front Dimensions - Clean Face and Iron Age

in. 27-3/8 23-1/8 37-3/16 1-1/4 6-3/4 32-7/8 34-1/8

mm 695 587 945 32 172 835 867

in. 34-3/8 25-3/16 44-3/16 1-1/4 6-3/4 34-13/16 36-1/16

mm 873 640 1122 32 172 884 916

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/21

B. Clearances to Combustibles

When selecting a location for the appliance it is important

to consider the required clearances to walls. See Figure

3.7.

WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access. Due to high temperatures, the appliance should be lo-

cated out of trac and away from furniture and draperies.

NOTE: THE REAR STANDOFF MAY NEED

TO BE REMOVED WHEN VENTING AT 45º

1/2 IN.

TOP VENT

ONE 90º ELBOW

NOTICE: Illustrations reect typical installations and are

FOR DESIGN PURPOSES ONLY. Illustrations/diagrams are not drawn to scale. Actual installation may vary due to individual design preference.

ALCOVE

INSTALLATION

6000

8000

Refer to Section 10.B for mantel and wall projection information.

Consider the mantel or cabinet system to be installed and comply with the necessary requirements for elevated hearth. Refer to instructions included with cabinet system.

REAR VENT,

HORIZONTAL TERMINATION

TWO ELBOWS

REAR VENT

NO ELBOWS

REAR VENT

ONE ELBOW

A B C D E F G H

in. 51 42 72 56-5/8

mm 1295 1067 1829 1438 559 451 203

in. 55-7/8 49 79 61-1/2

mm 1419 1245 2007 1562 559 502 254

See Section 10.B

Mantel Projections

See Section 10.B

Mantel Projections

22 17-3/4 8

22 19-3/4 10

Figure 3.7 Appliance Locations

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/2114

COMBUSTIBLE FLOORING MAY BE INSTALLED

NEXT TO THE FRONT OF THE APPLIANCE.

* MINIMUM FRAMING DIMENSIONS

A B C** D E F G H I J

Models

6000

8000

Rough

Opening

(Width)

in. 10 40-1/8 22 42 32 0 0 1/2 1/2 36

mm 254 1019 559 1067 813 0 0 13 13 914

in. 10 42-1/8 22 49 32 0 0 1/2 1/2 36

mm 254 1070 559 1245 813 0 0 13 13 914

* Adjust framing dimensions for interior sheathing (such as sheetrock)

C** Add 12 inches for rear venting with one 90º elbow.

Figure 3.8 Clearances to Combustibles

Rough

Opening

(Height)

Rough

Opening

(Depth)

Rough

Opening

(Width)

Clearance to Ceiling

(Measured from top of

appliance opening)

Combustible

Floor

Combustible

Flooring

Behind

Appliance

Sides of

Appliance

Front of

Appliance

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/21

C. Constructing the Appliance Chase

A chase is a vertical box-like structure built to enclose the gas appliance and/or its vent system. In cooler climates the vent should be enclosed inside the chase.

NOTICE: Treatment of ceiling restops and wall shield

restops and construction of the chase may vary with the

type of building. These instructions are not substitutes for the requirements of local building codes. Therefore, you MUST check local building codes to determine the requirements to these steps.

NOTICE: Where required by code, install only sprinkler heads with a sprinkler activation temperature

classied as Extra High.

• Sprinklers inside of chase: Keep sprinkler head away from vent and chimney.

• Heat Management applications: Maintain 36 inches of clearance to openings from which heat is discharged such as heat zone registers, etc. Refer to Section

6.B for Heat Management options allowed for this appliance.

Chases should be constructed and insulated in the same manner as the thermal envelope of the home based on

the code requirements for that climate zone to prevent air leakage and draft problems. The chase is an extension of the building thermal envelope.

To further prevent drafts and air leakage, the wall shield and ceiling restops should be caulked with caulk with a minimum of 300 ºF continuous exposure rating to seal gaps. Gas line holes and other openings should

be caulked with caulk with a minimum of 300 ºF continu-

ous exposure rating or stu󰀨ed with unfaced insulation. If the

appliance is being installed on a cement surface, a layer of plywood may be placed underneath to prevent conducting

cold up into the room.

NOTICE: Install appliance on hard metal or wood surfaces extending full width and depth. DO NOT install directly on carpeting, vinyl, tile or any combustible material other than wood.

WARNING! Risk of Fire! Maintain specied air space

clearances to appliance and vent pipe:

• Insulation and other materials must be secured to prevent

accidental contact.

• The chase must be properly blocked to prevent blown

insulation or other combustibles from entering and

making contact with replace or chimney.

• Failure to maintain airspace may cause overheating and

a re.

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/2116

4 4

A B

Termination Location and Vent Information

A. Vent Termination Minimum Clearances

Fire Risk.

Maintain vent clearance to combustibles as

specied.

• DO NOT pack air space with insulation or other

Failure to keep insulation or other materials away from vent pipe could cause overheating and re.

2 FT.

MIN.

GAS DIRECT VENT TERMINATION CAP

materials.

WARNING

HORIZONTAL

OVERHANG

20 INCHES MIN.

LOWEST

DISCHARGE

OPENING

H (MIN.) - MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE OPENING

ROOF PITCH

VERTICAL

IS X/ 12

WALL

6 in. (minimum) up to 20 in.

152 mm/508 mm

20 in. and over 0 in. minimum

18 in. minimum

457 mm

Gas, Wood or Fuel Oil

Termination Cap

A *

Gas

Termination

Cap **

If using decorative cap cover(s), this distance may need to be

increased. Refer to the installation instructions supplied with the decorative cap cover.

In a staggered installation with both gas and wood or fuel oil

terminations, the wood or fuel oil termination cap must be higher than the gas termination cap.

Roof Pitch H (Min.) Ft.

Flat to 6/12...........................................................1.0*

Over 6/12 to 7/12 .................................................1.25*

Over 7/12 to 8/12 .................................................1.5*

Over 8/12 to 9/12 .................................................2.0*

Over 9/12 to 10/12 ...............................................2.5*

Over 10/12 to 11/12 .............................................3.25

Over 11/12 to 12/12 .............................................4.0

Over 12/12 to 14/12 .............................................5.0

Over 14/12 to 16/12 .............................................6.0

Over 16/12 to 18/12 .............................................7.0

Over 18/12 to 20/12 .............................................7.5

Over 20/12 to 21/12 .............................................8.0

* H minimum may vary depending on regional snowfall.

Refer to local codes.

Figure 4.1 Minimum Height From Roof to Lowest Discharge Opening

Figure 4.2 Staggered Termination Caps

CAUTION! Risk of Burns! Termination caps are HOT,

consider proximity to doors, trac areas or where people

may pass or gather (sidewalk, deck, patio, etc.). Listed cap shields available. Contact your dealer.

• Local codes or regulations may require different

clearances.

• Hearth & Home Technologies assumes no responsibility for the improper performance of the appliance when the

venting system does not meet these requirements.

• Vinyl protection kits are suggested for use with vinyl siding.

• Measure horizontal and vertical termination cap clearances as noted in Figure 4.3.

H=Measure Horizontal Distances from H V=Measure Vertical Distances from V

CLEARANCE

= 6 IN.

Figure 4.3

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/21

B. Vent Terminal Clearances

U.S.A. Installations: In accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code. Canadian Installations: In accordance with the current CSA B149.1, Natural Gas and Propane Installation Code.

= AREA WHERE TERMINAL IS NOT PERMITTED

= AIR SUPPLY INLET

= VENT TERMINAL

H or i

U.S.A. CANADA

Electrical

Service

A Clearance above grade,veranda, porch, deck, or balcony 12 in. (305 mm) 12 in. (305 mm)

Clearance to window or door that may be opened, or to permanently closed window

U.S.A.: = 9 in. min. (229 mm min.) CANADA: = 12 in. min. ( 305 mm min.)

clearance below unventilated so󰀩t 18 in. (457 mm) 18 in. (457 mm)

clearance below ventilated so󰀩t 18 in. (457 mm) 18 in. (457 mm)

clearance below any vinyl so󰀩ts and electrical service 30 in. (762 mm) 30 in. (762 mm)

D clearance to outside corner 6 in. (152 mm) 6 in. (152 mm) E clearance to inside corner 6 in. (152 mm) 6 in. (152 mm)

not to be installed above a gas meter/regulator assembly within 3 feet horizontally from

the center-line of the regulator

3 ft (914 mm) 3 ft (914 mm)

G clearance to gas service regulator vent outlet 3 ft (914 mm) 3 ft (914 mm)

clearance to non-mechanical air supply inlet to building or the combustion air inlet to

any other appliance termination (mechanical or non-mechanical)

9 in. min.

(229 mm min.)

12 in. min.

(305 mm min.)

clearance to a mechanical (powered) air supply inlet

***(All mechanical air intakes within 10 feet of a horizontal termination cap must be

3 ft (914 mm)*** 6 ft (1.8 m)

a minimum of 3 feet below termination.)

On public property: clearance above paved sidewalk or a paved driveway.

7 ft (2.1 m) 7 ft (2.1 m)**

**(A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings.)

clearance from sides of electrical service 6 in. (152 mm) 6 in. (152 mm)

Location of the vent termination must not interfere with access to the electrical service.

clearance above electrical service 12 in. (305 mm) 12 in. (305 mm)

Location of the vent termination must not interfere with access to the electrical service.

clearance under veranda, porch, deck, balcony or overhang *(Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of

two sides beneath the oor.)

vinyl or composite overhang 42 in. (1067 mm) 42 in. (1067 mm)

Figure 4.4 Minimum Clearances for Termination

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/2118

18 in. (457 mm) 12 in. (305 mm)*

C. Approved Pipe

This appliance is approved for use with Hearth & Home

Technologies DVP or SLP venting systems. Refer to Sec-

tion 12.A for vent component information and dimensions. Only use listed decorative termination caps/shrouds with Hearth & Home Technologies approved venting systems.

DO NOT mix pipe, ttings or joining methods from di󰀨er-

ent manufacturers.

The pipe is tested to be run inside an enclosed wall.

There is no requirement for inspection openings at each

joint within the wall.

WARNING! Risk of Fire or Asphyxiation. This appli- ance requires a separate vent. DO NOT vent to a pipe serving a separate solid fuel burning appliance.

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/21

D. Use of Elbows

Diagonal runs have both vertical and horizontal vent as-

pects when calculating the e󰀨ects. Use the rise for the vertical aspect and the run for the horizontal aspect. See Figure 4.5.

Two 45º elbows may be used in place of one 90º elbow. On 45º runs, one foot of diagonal is equal to 8-1/2 in. (216 mm) horizontal run and 8-1/2 in. (216 mm) vertical run. A length of straight pipe is allowed between two 45º elbows. See Figure 4.5.

Figure 4.6 shows the vertical and horizontal o󰀨sets for DVP or SLP elbows.

VERTICAL

Vent

Type

Inches Millimeters Inches Millimeters

DVP 6-5/8 168 16-1/2 419

SLP 5-1/4 133 11-3/8 289

X Y

RISE

SLP

Pipe

EFFECTIVE

LENGTH

RUN

HORIZONTAL

E󰀨ective Length Rise/Run

Inches Millimeters Inches Millimeters

SLP4 4 102 2-3/4 70

SLP6 6 152 4-1/4 108 SLP12 12 305 8-1/2 216 SLP24 24 610 17 432 SLP36 36 914 25-1/2 648 SLP48 48 1219 34 864 SLP6A 3 to 6 76 to 152

SLP12A 3 to 12 76 to 305

DVP Pipe

E󰀨ective Length Rise/Run

Inches Millimeters Inches Millimeters

2-1/8-4-1/4 54-108 2-1/8-8-1/2 54-216

DVP4 4 102 2-3/4 70

DVP6 6 152 4-1/4 108

DVP12 12 305 8-1/2 216 DVP24 24 610 17 432 DVP36 36 914 25-1/2 648 DVP48 48 1219 34 864 DVP6A 3 to 6 76 to 152

DVP12A 3 to 12 76 to 305

2-1/8-4-1/4 54-108 2-1/8-8-1/2 54-216

Vent Type

Inches Millimeters

DVP 16-1/4 413 SLP 11-1/4 286

Figure 4.6 Vertical and Horizontal O󰀨set for DVP and SLP Elbows

Figure 4.5

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/2120

E. Measuring Standards

Vertical and horizontal measurements listed in the vent

diagrams were made using the following standards:

• Pipe measurements are shown using the e󰀨ective length of pipe. See Section 12.A (Figure 12.1 for DVP, Figure

12.8 for SLP) for information on e󰀨ective length of pipe components.

• Horizontal terminations are measured to the outside mounting surface (ange of termination cap) (see Figure

4.7).

• Vertical terminations are measured to top of last section of pipe. See Figure 4.8.

• Horizontal pipe installed level with no rise.

MEASURE TO SHADED SURFACE (OUTSIDE MOUNTING SURFACE)

Figure 4.7 Measure to Outside Mounting Surface

Figure 4.8 Measure to Top of Last Section of Pipe

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/21

F. Vent Diagrams

General Rules:

• SUBTRACT 3 ft. from the total H measurement for each 90º elbow installed horizontally.

• SUBTRACT 1-1/2 ft. from the total H measurement for each 45º elbow installed horizontally.

• A maximum of three 90º elbows (or six 45º elbows) may be used in any vent conguration. Some elbows may be installed horizontally. For example, see Figure 4.18.

• Elbows may be placed back to back anywhere in the system.

WARNING

Fire Risk. Explosion Risk.

Do NOT pack insulation or other combustibles between ceiling restops.

• ALWAYS maintain specied clearances around venting and restop systems.

• Install wall shield and ceiling restops as speci-

ed.

Failure to keep insulation or other material away from vent pipe may cause re.

• Any 90º elbow may be replaced with two back to back

45º elbows.

• When penetrating a combustible wall, a wall shield

restop must be installed.

• When penetrating a combustible ceiling, a ceiling restop must be installed.

• Horizontal runs of vent do not require vertical rise; horizontal runs may be level.

• Horizontal termination cap should have a 1/4 inch

downward slant to allow any moisture in cap to be

released. See Figure 4.9.

WARNING

Fire Risk.

• When using DVP-HRC-SS and DVP-HRC-ZCSS termination caps on top vented replaces, a

6 inch minimum vertical vent section is required

before installing rst elbow.

Note: The 6000/8000 series replaces can adapt to SLP

series vent pipe, if desired.

When venting o󰀨 the top of the unit, use a DVP-2SL adapter and a minimum 48 inch vertical section of SLP series vent pipe.

A DVP-SLP24 adapter may also be used with a 24 inch vertical section of SLP series vent pipe.

After the 48 inch vertical section, the venting table rules must

be followed. The rst 48 inch vertical section is NOT counted

as part of the vertical components in the table. It is still counted as part of the overall maximum run. All venting table rules for the vent run must still be followed.

Example: DVP pipe 3 ft. min. vertical = 11 ft. max. horizontal

SLP pipe 7 ft. min. vertical = 11 ft. max. horizontal

1/4 in. max.

Figure 4.9

(6 mm)

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/2122

Top Vent - Horizontal Termination

ELBOW HEAT SHIELD (Required when V

= 2 ft. or less)

One Elbow

Note: For corner installations: A 6 inch (152

mm) section of straight pipe may need to

be attached to the appliance before a 90º

elbow, to allow the vent pipe to clear the top

stando󰀨s.

6000CL-IFT

Minimum H1 Maximum

Elbow only 2 ft 610 mm

6 in. 152 mm 6 ft. 1.8 m

1 ft. 305 mm 11 ft. 3.3 m

1-1/2 ft. 457 mm 18 ft. 5.5 m

2 ft. 1.2 m 25 ft. 7.6 m

+ H

= 40 ft. (12.2 m) Maximum

= 25 ft. (7.6 m) Maximum

WARNING! Risk of Fire! Elbow heat shield required when V1 = 2 ft. or less. Clearances to combustibles must be maintained. See Section 5.A.

8000CL-IFT

Minimum H1 Maximum

Elbow only 2 ft. 610 mm 6 in. 152 mm 2 ft. 610 mm 1 ft. 305 mm 5 ft. 1.5 m

1-1/2 ft. 457 mm 10 ft. 3.0 m

2 ft. 610 mm 18 ft. 5.5 m

2-1/2 ft. 762 mm 22 ft 6.7 m

+ H

= 40 ft. (12.2 m) Maximum

= 22 ft. (6.7 m) Maximum

Figure 4.10

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/21

Top Vent - Horizontal Termination - (continued)

Two Elbows

Note: For corner installations: A 6 in.

(152 mm) section of straight pipe may need to be attached to the appliance

before a 90º pipe to clear the top stando󰀨s.

elbow, to allow the vent

6000CL-IFT

Minimum H1 + H2 Maximum

Elbow only 1 ft. 305 mm

6 in. 152 mm 4 ft. 1.2 m

1 ft. 305 mm 11 ft. 3.4 mm

1.5 ft. 457 mm 18 ft. 5.5 m 2 ft. 610 mm 24 ft. 7.3 m

+ H1 + H

H1 + H

= 40 ft. (12.2 m) Maximum

= 24 ft. (7.3 m) Maximum

8000CL-IFT

Minimum H1 + H2 Maximum

Elbow only Not allowed

6 in. 152 mm Not allowed

1 ft. 305 mm 2 ft. 610 mm

1.5 ft. 457 mm 6 ft. 1.8 m 2 ft. 610 mm 11 ft. 3.4 m

2.5 ft. 762 mm 18 ft. 5.5 m 3 ft. 914 mm 24 ft. 7.3 m

+ H1 + H

H1 + H

= 40 ft. (12.2 m) Maximum

= 24 ft. (7.3 m) Maximum

V1 = 1 ft. (305 mm) Minimum

Figure 4.11

INSTALLED

HORIZONTALLY

Heat & Glo • 6000CL-IFT, 8000CL-IFT Installation Manual • 2504-980 Rev. N • 3/2124

+ 55 hidden pages