Hearth and Home Technologies LCOR-36TRB-IPI, PIER-36TRB-IPI, ST-36TRB-IPI, RCOR-36TRB-IPI User Manual

Download

Page 1

Models: ST-36TRB-IPI PIER-36TRB-IPI LCOR-36TRB-IPI RCOR-36TRB-IPI

Owner’s Manual

Installation and Operation

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating and maintenance instructions included.

WARNING: If the information in these instructions is not followed exactly, a ﬁ re or explosion may result causing property damage, personal injury, or death.

• DO NOT store or use gasoline or other ﬂ am- mable vapors and liquids in the vicinity of this or any other appliance.

• What to do if you smell gas

- DO NOT try to light any appliance.

- DO NOT touch any electrical switch. DO

NOT use any phone in your building.

- Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s instructions.

- If you cannot reach your gas supplier, call

the ﬁ re department.

• Installation and service must be performed by a qualiﬁ ed installer, service agency , or the gas supplier.

This appliance may be installed as an OEM installation in manufactured home (USA only) or mobile home and must be installed in accordance with the manufacturer’s instructions and the manufactured home construction and safety standard,

Title 24 CFR, Part 3280 or Standard for Installation in Mobile Homes, CAN/CSA Z240MH, in Canada.

This appliance is only for use with the type(s) of gas indicated on the rating plate.

• Read, understand and follow these instructions for safe installation and operation.

DO NOT

DISCARD

• Leave this manual with party responsible for use and operation.

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

• DO NOT touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as ﬁ replace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other ﬂ ammable materials.

• Keep clothing, furniture, draperies and other ﬂ ammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the ﬁ xed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas ﬁ tter.

See Table of Contents for location of additional Commonwealth of Massachusetts requirements.

Installation and service of this appliance should be performed by qualiﬁ ed personnel. Hearth & Home Technologies suggests NFI certiﬁ ed or factory trained professionals, or technicians supervised by an NFI certiﬁ ed professional.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 1

Page 2

Read this manual before installing or operating this appliance.

Please retain this owner’s manual for future reference.

A. Congratulations

Congratulations on selecting a Heat & Glo gas ﬁ replace, an elegant and clean alternative to wood burning ﬁ replaces. The Heat & Glo gas ﬁ replace you have selected is designed to provide the utmost in safety, reliability, and efﬁ ciency.

As the owner of a new ﬁ replace, you’ll want to read and carefully follow all of the instructions contained in this owner’s manual. Pay special attention to all cautions and warnings.

Homeowner Reference Information

This owner’s manual should be retained for future reference. We suggest that you keep it with your other important documents and product manuals.

The information contained in this owner’s manual, unless noted otherwise, applies to all models and gas control systems.

Your new Heat & Glo gas ﬁ replace will give you years of durable use and trouble-free enjoyment. Welcome to the Heat & Glo family of ﬁ replace products!

We recommend that you record the following pertinent information about your ﬁ replace.

Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: __________________________________________ Location on ﬁ replace: _____________________ Dealership purchased from: _______________________________ Dealer Phone: __________________________ Notes: _______________________________________________________________________________________ _____________________________________________________________________________________________

Listing Label Information/Location

This product may be covered by one or more of the following patents: (Nos produits sont couverts par un ou plusieurs des brevets suivants): (United States) 4593510,4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356,5341794, 5347983, 5429495, 5452708,5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485,5931661, 5941237, 594711 2,5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, D320652, D445174, D462436; (Canada)1297749, 2195264, 2225408; or other U.S. and foreign patents pending (ou autresbrevetsamericainsetetrangersenattente).

Type of Gas

Not for use with solid fuel . (Ne doit pas entre utilise avec un combustible solide).

Ty pe of Gas (Sorte De Gaz) :

NATURA L GAS

Gas and Electric Information

Minimum Permissible Gas Supply for Purpos es of Input Adjustment . Approved Minimum (De Gaz) Acceptabl e 0. 0 in w. c. (Po. Col. d’eau) Maximum Pressure (Pression) 0. 0 in w. c. (Po. Col. d’eau) Maximum Manifold Pressure (Pression) 0. 0 in w. c. (Po. Col. d’eau) Minimum Manifold Pressure (Pression) 0. 0 in w. c. (Po. Col. d’eau) T o tal Electrical Requirements: 000V ac, 00Hz., less than 00 Ampere s

AL TI TUDE : 0-0000 FT . 0000-0000FT . MAX. INPU T BTUH: 00,000 00,000 MIN. INPU T BTUH: 00,000 00,000 ORIFICE SIZE: #XXXXX #XXXXX

The model information regarding your speciﬁ c ﬁ replace can be found on the rating plate usually located in the control area of the ﬁ replace.

He at & Gl o, a of Hearth & Ho me Te chnologies, Inc. 20802 Kensington Boulevard, Lakeville, MN 5504 4

This appliance must be installed in accordance with local codes, if any; if not, follow ANSI Z223.1 in the USA or CAN/CG A B149 installation codes. (Installer l’ appa re il selon les codes ou regl emen ts

lo caux ou , en l’absence de tels reglements, selon les codes d’in stallation CAN/CGA-B149.)

bran d

ANSI Z21X X-XXXX · CS A 2.XX-MXX · UL307B

IN CANADA

Mode l:

(Modele):

Serial

(Serie):

XXXXXXXX

MADE IN US A

Model Number

Serial Number

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/082

Page 3

Safety Alert Key:

• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.

• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• NOTICE: Used to address practices not related to personal injury.

Table of Contents

A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

B. Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1 Listing and Code Approvals

A. Appliance Certiﬁ cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

B. Tempered Glass Speciﬁ cations . . . . . . . . . . . . . . . . . . . . . 7

C. BTU Speciﬁ cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . . 7

E. Non-Combustible Materials Speciﬁ cation. . . . . . . . . . . . . . 7

F. Combustible Materials Speciﬁ cation . . . . . . . . . . . . . . . . . 7

G. Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

H. Requirements for the Commonwealth of Massachusetts . . 8

User Guide

2 Operating Instructions

A. Gas Fireplace Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

B. Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

C. Fan Kit (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

D. Clear Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

E. Decorative Doors and Fronts . . . . . . . . . . . . . . . . . . . . . . 10

F. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

G. Remote Controls, Wall Controls and Wall Switches . . . . . 10

H. Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . 10

I. Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 11

J. After Fireplace is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

K. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 12

3 Maintenance and Service

A. Maintenance Tasks-Homeowner . . . . . . . . . . . . . . . . . . . 13

B. Maintenance Tasks-Qualiﬁ ed Service Technician . . . . . . 14

Installer Guide

4 Getting Started

A. Typical Appliance System. . . . . . . . . . . . . . . . . . . . . . . . . 16

B. Design and Installation Considerations . . . . . . . . . . . . . . 17

C. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . 17

D. Inspect Appliance and Components . . . . . . . . . . . . . . . . . 17

5 Framing and Clearances

A. Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . . 18

B. Constructing the Appliance Chase . . . . . . . . . . . . . . . . . . 19

C. Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

D. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 21

6 Termination Locations

A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 23

B. Continue Adding Vent Components . . . . . . . . . . . . . . . . . 25

C. Install Support Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . 25

7 Vent Information and Diagrams

A. Approved Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

B. Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

C. Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

D. Measuring Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

E. Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

8 Vent Clearances and Framing

A. Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . . 37

B. Wall Penetration Framing . . . . . . . . . . . . . . . . . . . . . . . . . 37

C. Vertical Penetration Framing . . . . . . . . . . . . . . . . . . . . . . 38

D. Install Attic Insulation Shield . . . . . . . . . . . . . . . . . . . . . . . 39

9 Appliance Preparation

A. Top Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

B. Rear Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

C. Securing and Leveling the Appliance . . . . . . . . . . . . . . . . 42

10 Installing Vent Pipe (DVP and SLP Pipe)

A. Assemble Vent Sections (DVP Pipe Only) . . . . . . . . . . . . 43

B. Assemble Vent Sections (SLP Pipe Only) . . . . . . . . . . . . 44

C. Assemble Slip Sections . . . . . . . . . . . . . . . . . . . . . . . . . . 44

D. Secure the Vent Sections . . . . . . . . . . . . . . . . . . . . . . . . . 45

E. Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . . 45

F. Install Decorative Ceiling Components (SLP only) . . . . . . 46

G. Install Metal Roof Flashing . . . . . . . . . . . . . . . . . . . . . . . . 47

H. Assemble and Install Storm Collar . . . . . . . . . . . . . . . . . . 47

I. Install RF4-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

J. Install Vertical Termination Cap . . . . . . . . . . . . . . . . . . . . 49

K. Install Decorative Wall Components (SLP only) . . . . . . . . 49

L. Heat Shield Requirements for Horizontal Termination . . . 49 M. Install Horizontal Termination Cap (DVP and SLP Pipe) . 50

11 Gas Information

A. Fuel Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

B. Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

D. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . 51

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 3

Page 4

12 Electrical Information

A. Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

B. Intelliﬁ re Ignition System Wiring . . . . . . . . . . . . . . . . . . . . 52

C. Optional Accessories Requirements . . . . . . . . . . . . . . . . 52

D. Electrical Service and Repair . . . . . . . . . . . . . . . . . . . . . . 52

E. Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 54

F. Wall Switch Installation for Fan (Optional) . . . . . . . . . . . . 54

13 Finishing

A. Splatter Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

B. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 57

C. Facing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

D. Finishing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

E. Elevated Hearth Systems . . . . . . . . . . . . . . . . . . . . . . . . . 60

14 Appliance Setup

A. Remove Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . 61

B. Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . . 61

C. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

D. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

E. Lava Rock and Glowing Ember Placement . . . . . . . . . . . 61

F. Install the Log Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . 62

G. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

H. Install Trim Kits and Surrounds . . . . . . . . . . . . . . . . . . . . 64

I. Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

15 Troubleshooting

A. Intelliﬁ re Ignition System . . . . . . . . . . . . . . . . . . . . . . . . . 65

16 Reference Materials

A. Appliance Dimension Diagram . . . . . . . . . . . . . . . . . . . . . 67

B. Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . . 70

C. Service Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

D. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

 = Contains updated information.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/084

Page 5



B. Limited Lifetime Warranty Hearth & Home Technologies LIMITED WARRANTY

Hearth & Home Technologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood, pellet and electric appliances purchased from an authorized HHT dealer and installed in the United States of America or Canada. Warranty starts with date of purchase by the original owner (End User) except as noted for replacement parts.

Warranty Period HHT Manufactured Appliances and Venting Parts Labor Gas Wood Pellet

1 Year XXXXXX

EPA

Wood

Electric Venting

Components Covered

All Parts and Material Except as

covered by Conditions, Exclusion,

and Limitations listed

2 years

3 years X Firepots

5 years 3 years X X Castings & Bafﬂ es

7 years 3 years X X X

10 years 1 year X Burners, Logs & Refractory

Limited

Lifetime

1 year X Firebox & Heat Exchanger

90 Days XXXXXX All Replacement Parts

XXXX Blowers

X Molded Refractory Panels

Igniters, Electronic Components,

and Glass

Firebox, HHT Chimney,

Termination & Heat

Exchanger

See Conditions, Exclusions, and limitations. 9-01-08

CONDITIONS, EXCLUSIONS & LIMITATION OF LIABILITY

• This warranty applies to the original owner and is transferable up to two years from date of purchase to the new homeowner, provided the purchase was made through an authorized dealer or distributor of HHT, and the appliance remains in its original place of installation.

• The maximum amount recoverable under this warranty is limited to the purchase price of the product.

• In no event shall HHT be liable for any incidental or consequential damages caused by defects in the product.

• Adjustments, regular maintenance, cleaning and temporary repairs, or the failure to duplicate the problem in the home is not covered under this warranty.

Page 1 of 2 4021-645A 09-01-08

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 5

Page 6

B. Limited Lifetime Warranty (continued)

• This limited warranty does not extend to or include surface ﬁ nish on the appliance or terminations, door gasketing, glass gasketing, glass discoloration, ﬁ rebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or corrosion on any of the metal surfaces, cast iron components, bafﬂ es, ﬁ repots, doors, or ﬁ rebox area are not covered by this warranty.

• Noise resulting from minor expansion, contraction, or movement of certain parts is normal and complaints related to this noise are not covered by this warranty.

• HHT’s obligation under this warranty does not extend to damages resulting from: (1) installation, operation or maintenance of the appliance not in accordance with the installation instructions; operating instructions and the listing agent identiﬁ cation label furnished with the appliance; (2) installation which does not comply with local building codes; (3) shipping, improper handling, improper operation, abuse, misuse, accident or unworkmanlike repairs; (4) environmental conditions, inadequate ventilation or drafting caused by tight sealing construction of the structure or handling devices such as exhaust fans or forced air furnaces or other such causes; (5) use of fuels other than those speciﬁ ed in the operating instructions; (6) installation or use of components not supplied with the appliance or any other components not expressly authorized and approved by HHT; and/or (7) modiﬁ cation of the appliance not expressly authorized and approved by HHT in writing.

• This warranty does not apply to non-HHT venting components, hearth components or other accessories used in conjunction with the installation of this product.

• This warranty is void if the appliance has been over-ﬁ red or operated in atmospheres contaminated by chlorine, ﬂ uorine, or other damaging chemicals the appliance is subject to prolonged periods of dampness or condensation, or there is any damage to the appliance or other components due to water or weather damage which is the result of, but not limited to, improper chimney or venting installation.

• HHT’s liability under this warranty is limited to the replacement and repair of defective components or workmanship during the applicable period. HHT may fully discharge all of its obligations under such warranties by repairing the defective component(s) at HHT’s discretion. Shipping costs are not covered under this warranty.

• Some states do not allow exclusions or limitation of incidental or consequential damages, so those limitations may not apply to you. This warranty gives you speciﬁ c rights; you may also have other rights, which vary from state to state.

• EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE WARRANTY SPECIFIED ABOVE.

This Limited Warranty is effective on all HHT appliances sold after September 01, 2008 and supersedes any and all warranties currently in existence.

If warranty service is needed, you should contact your installing dealer. If the installing dealer is unable to provide necessary parts or components, contact the nearest authorized HHT dealer or supplier.

Page 2 of 2

4021-645A 09-01-08

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/086

Page 7

Listing and Code Approvals

A. Appliance Certiﬁ cation

MODELS: ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI,

RCOR-36TRB-IPI

LABORATORY: Underwriters Laboratories, Inc. (UL) TYPE: Direct Vent Gas Appliance Heater STANDARD: ANSI Z21.88-2007 • CSA 2.33a-2007

This product is listed to ANSI standards for “Vented Gas Appliance Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and Recreational Vehicles”, and “Gas Fired Appliances for Use at High Altitudes”.

NOTICE: This installation must conform with local codes. In the absence of local codes you must comply with the National Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A. and the CAN/CGA B149 Installation Codes in Canada.

NOT INTENDED FOR USE AS A PRIMAR Y HEAT SOURCE.

This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be factored as primary heat in residential heating calculations.

B. Tempered Glass Speciﬁ cations

Hearth & Home Technologies appliances manufactured with tempered glass may be installed in hazardous locations such as bathtub enclosures as deﬁ ned by the Con- sumer Product Safety Commission (CPSC). The tempered glass has been tested and certiﬁ ed to the requirements of ANSI Z97.1 and CPSC 16 CFR 1202 (Safety Glazing Certiﬁ cation Council SGCC# 1595 and 1597. Architectur- al Testing, Inc. Reports 02-31919.01 and 02-31917.01).

This statement is in compliance with CPSC 16 CFR Sec- tion 1201.5 “Certiﬁ cation and labeling requirements” which refers to 15 U.S. Code (USC) 2063 stating “…Such certiﬁ cate shall accompany the product or shall otherwise be furnished to any distributor or retailer to whom the product is delivered.”

Some local building codes require the use of tempered glass with permanent marking in such locations. Glass meeting this requirement is available from the factory. Please contact your dealer or distributor to order.

C. BTU Speciﬁ cations

Models

(U.S. or Canada)

ST-36TRB-IPI PIER-36TRB-IPI LCOR-36TRB-IPI RCOR-36TRB-IPI

(0-2000 FT)

CANADA

(2000-4500 FT)

Maximum

Input

BTU/h

37,000 26,000 32 34,500 23,900 33

Minimum

Input

BTU/h

Oriﬁ ce

Size

(DMS)

D. High Altitude Installations

NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.

When installing above 2000 feet elevation:

• In the USA: Reduce input rate 4% for each 1000 feet above 2000 feet.

• In CANADA: Reduce input rate 10% for elevations between 2000 feet and 4500 feet. Above 4500 feet, consult local gas utility.

Check with your local gas utility to determine proper oriﬁ ce size.

E. Non-Combustible Materials Speciﬁ cation

Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750 ºC and UL763 shall be

considered non-combustible materials.

F. Combustible Materials Speciﬁ cation

Materials made of or surfaced with wood, compressed paper, plant ﬁ bers, plastics, or other material that can ignite and burn, whether ﬂ ame proofed or not, or plastered or unplastered shall be considered combustible materials.

G. Electrical Codes

NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code

ANSI/NFPA 70-latest edition or the Canadian Electric Code CSA C22.1.

• A 110-120 VAC circuit for this product must be protected

with ground-fault circuit-interrupter protection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 7

Page 8

Note: The following requirements reference various Massachuset ts and national codes not contained in this document.

H. Requirements for the Commonwealth of

Massachusetts

For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above ﬁ nished grade in the area of the venting, in- cluding but not limited to decks and porches, the following requirements shall be satisﬁ ed:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gas ﬁ tter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the ﬂ oor level where the gas equipment is to be installed. In addition, the installing plumber or gas ﬁ tter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualiﬁ ed licensed professionals for the installation of hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent ﬂ oor level. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

Inspection

The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.

Exemptions

The following equipment is exempt from 248 CMR

5.08(2)(a)1 through 4:

• The equipment listed in Chapter 10 entitled “Equipment

Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the Board; and

• Product Approved side wall horizontally vented gas fu-

eled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.

MANUFACTURER REQUIREMENTS Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

• Detailed instructions for the installation of the venting

system design or the venting system components; and

• A complete parts list for the venting system design or

venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the ﬂ ue gases, but identiﬁ es “special venting systems”, the following requirements shall be satisﬁ ed by the manufacturer:

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certiﬁ ed.

Signage

A metal or plastic identiﬁ cation plate shall be permanent- ly mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, “GAS

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/088

• The referenced “special venting system” instructions

shall be included with the appliance or equipment installation instructions; and

• The “special venting systems” shall be Product Ap-

proved by the Board, and the instructions for that system shall include a parts list and detailed installation instructions.

A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

See Gas Connection section for additional Commonwealth of Massachusetts requirements.

Page 9

Operating Instructions

User Guide

A. Gas Fireplace Safety

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

• DO NOT touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as ﬁ replace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other ﬂ ammable materials.

• Keep clothing, furniture, draperies and other ﬂ ammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the ﬁ xed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

If you expect that small children or vulnerable adults may come into contact with this ﬁ replace, the following precau- tions are recommended:

• Install a physical barrier such as:

- A decorative ﬁ rescreen.

- Adjustable safety gate.

• Install a switch lock or a wall/remote control with child protection lockout feature.

• Keep remote controls out of reach of children.

• Never leave children alone near a hot ﬁ replace, whether operating or cooling down.

• Teach children to NEVER touch the ﬁ replace.

• Consider not using the ﬁ replace when children will be present.

Contact your dealer for more information, or visit: www. hpba.org/staysafe.

T o prevent unintended operation when not using your ﬁ re- place for an extended period of time (summer months, vacations, trips, etc):

• Remove batteries from remote controls.

• Turn off wall controls.

• Unplug 3 volt adapter plug and remove batteries on IPI models.

B. Your Fireplace

WARNING! DO NOT operate ﬁ replace before read- ing and understanding operating instructions. Failure

to operate ﬁ replace according to operating instructions could cause ﬁ re or injury.

Figure 2.1 General Operating Parts

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 9

DECORATIVE DOORS

(NOT SHOWN)

SECTION 2.E.

CLEAR SPACE

SECTION 2.D.

FIXED GLASS ASSEMBLY

SECTION 14.K.

HEARTH

MANTEL

Page 10

C. Fan Kit (optional)

If desired, a fan kit may be added. Contact your dealer to order the correct fan kit.

D. Clear Space

WARNING! DO NOT place combustible objects in front of the ﬁ replace or block louvers. High temperatures may start a ﬁ re. See Figure 2.2.

A void placing candles and other heat-sensitive objects on mantel or hearth. Heat may damage these objects.

3 FT. IN FRONT OF FIREPLACE

CLE

AR S

PACE

Figure 2.2 Clear Space

F. Fixed Glass Assembly

See Section 14.G.

G. Remote Controls, Wall Controls and Wall

Switches

Follow the instructions supplied with the control installed to operate your ﬁ replace:

For safety:

• Install a switch lock or a wall/remote control with child protection lockout feature.

• Keep remote controls out of reach of children.

See your dealer if you have questions.

H. Before Lighting Fireplace

Before operating this ﬁ replace for the ﬁ rst time, have a qualiﬁ ed service technician:

• Verify all shipping materials have been removed from inside and/or underneath the ﬁ rebox.

• Review proper placement of logs, ember material and/or other decorative materials.

• Check the wiring.

• Check the air shutter adjustment.

• Ensure that there are no gas leaks.

• Ensure that the glass is sealed and in the proper position and that the integral barrier is in place.

WARNING! Risk of Fire or Asphyxiation! DO NOT operate ﬁ replace with ﬁ xed glass assembly removed.

E. Decorative Doors and Fronts

WARNING! Risk of Fire! Install ONLY doors or fronts approved by Hearth & Home Technologies. Unapproved doors or fronts may cause ﬁ replace to overheat.

This fireplace has been supplied with an integral barrier to prevent direct contact with the ﬁ xed glass panel. DO NOT operate the ﬁ replace with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

For more information refer to the instructions supplied with your decorative door or front.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0810

Page 11

I. Lighting Instructions (IPI)

The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer. To prolong battery life, remove them when using the transformer.

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a ﬁ re or explosion

may result causing property damage, personal injury or loss of life.

A. This appliance is equipped with an

intermittent pilot ignition (IPI) device which automatically lights the burner. DO NOT try to light the burner by hand.

B. BEFORE LIGHTING, smell all around

the appliance area for gas. Be sure to smell next to the ﬂ oor because some gas is heavier than air and will settle on the ﬂ oor.

WHA T TO DO IF YOU SMELL GAS

• DO NOT try to light any appliance.

• DO NOT touch any electric switch; do not use any phone in your building.

WARNING:

DO NOT CONNECT 110 VAC TO THE CONTROL VALVE.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or fuel combustion which are known to the State of California to cause cancer, birth defects, or other reproductive harm.

Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁ re department.

C. DO NOT use this appliance if any

part has been under water. Immediately call a qualiﬁ ed service tech- nician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

CAUTION:

Hot while in operation. DO NOT touch. Keep children, clothing, furniture, gasoline and other liquids having ﬂ ammable vapors away.

DO NOT operate the appliance with ﬁ xed glass assembly removed, cracked or broken. Replacement of the ﬁ xed glass assembly should be done by a licensed or qualiﬁ ed service person.

NOT FOR USE

WITH SOLID FUEL

For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.

Also Certiﬁ ed for Installation in a Bedroom or a Bedsitting Room.

For assistance or additional information, consult a qualiﬁ ed installer, ser- vice agency or the gas supplier.

LIGHTING

INSTRUCTIONS

(IPI)

1. Turn off all electric power to the appliance.

2. This appliance is equipped with an ignition

device which automatically lights the burner.

DO NOT try to light the burner by hand.

GAS

VALVE

3. Wait ﬁ ve (5) minutes to clear out any gas.

Then smell for gas, including near the ﬂ oor. If you smell gas, STOP! Follow “B” in the Safety Information located on the left side of this label. If you do not smell gas, go to next step.

4. Turn on all electric power to the appliance.

5. To light the burner, ﬂ ip the ON/OFF switch to

the “ON” position. (The ON/OFF switch may include a wall switch if so equipped).

6. If the appliance will not operate, follow the instructions “To Turn Off Gas to Appliance” and call your service technician or gas supplier.

TO TURN OFF

GAS TO APPLIANCE

1. Turn wall control or ON/OFF switch to “OFF”.

2. Turn off all electric power to the appliance if

service is to be performed.

593-913F

Hearth & Home Technologies ﬁ replace, please refer to www.ﬁ replaces.com.

For additional information on operating your

Final inspection by

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 11

Page 12

J. After Fireplace is Lit

Initial Break-in Procedure

• The fireplace should be run three to four hours continuously on high.

• Turn the ﬁ replace off and allow it to completely cool.

• Remove ﬁ xed glass assembly. See Section 14.G.

• Clean ﬁ xed glass assembly. See Section 3.

• Replace the ﬁ xed glass assembly and run continuously on high an additional 12 hours.

This cures the materials used to manufacture the ﬁ re- place.

NOTICE! Open windows for air circulation during ﬁ re- place break-in.

• Some people may be sensitive to smoke and odors.

• Smoke detectors may activate.

K. Frequently Asked Questions

ISSUE SOLUTIONS

Condensation on the glass

Blue ﬂ ames

Odor from ﬁ replace

Film on the glass

Metallic noise

This is a result of gas combustion and temperature variations. As the ﬁ replace warms, this condensation will disappear.

This is a result of normal operation and the ﬂ ames will begin to yellow as the ﬁ replace is al- lowed to burn for 20 to 40 minutes.

When ﬁ rst operated, this ﬁ replace may release an odor for the ﬁ rst several hours. This is caused by the curing of materials from manufacturing. Odor may also be released from ﬁ nishing materials and adhesives used near the ﬁ replace. These circumstances may require additional curing related to the installation environment.

This is a normal result of the curing process of the paint and logs. Glass should be cleaned within 3 to 4 hours of initial burning. A non-abrasive cleaner such as gas ﬁ replace glass cleaner may be necessary. See your dealer.

Noise is caused by metal expanding and contracting as it heats up and cools down, similar to the sound produced by a furnace or heating duct. This noise does not affect the operation or longevity of the ﬁ replace.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0812

Page 13

Maintenance and Service

Any safety screen or guard removed for servicing must be replaced prior to operating the ﬁ replace.

When properly maintained, your ﬁ replace will give you many years of trouble-free service. We recommend annual service by a qualiﬁ ed service technician.

A. Maintenance Tasks-Homeowner

Installation and repair should be done by a qualiﬁ ed service technician only. The ﬁ replace should be inspected before use and at least annually by a professional service person.

The following tasks may be performed annually by the homeowner. If you are uncomfortable performing any of the listed tasks, please call your dealer for a service appointment.

More frequent cleaning may be required due to lint from carpeting or other factors. Control compartment, burner and circulating air passageway of the ﬁ replace must be kept clean.

CAUTION! Risk of Burns! The ﬁ replace should be turned off and cooled before servicing.

Glass Cleaning

Frequency: Seasonally By: Homeowner Tools Needed: Protective gloves, glass cleaner, drop

cloth and a stable work surface.

CAUTION! Handle ﬁ xed glass assembly with care.

Glass is breakable.

• Avoid striking, scratching or slamming glass

• Avoid abrasive cleaners

• DO NOT clean glass while it is hot

• Prepare a work area large enough to accommodate ﬁ xed glass assembly and door frame by placing a drop cloth on a ﬂ at, stable surface.

Note: Fixed glass assembly and gasketing may have residue that can stain carpeting or ﬂ oor surfaces.

• Remove door or decorative front from ﬁ replace and set aside on work surface.

• See Section 14.G for instructions to remove ﬁ xed glass assembly.

• Clean glass with a non-abrasive commercially available cleaner.

- Light deposits: Use a soft cloth with soap and water

- Heavy deposits: Use commercial fireplace glass

cleaner (consult with your dealer)

• Carefully set ﬁ xed glass assembly in place on ﬁ replace. Hold glass in place with one hand and secure glass latches with the other hand.

• Reinstall door or decorative front.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 13

Doors, Surrounds, Fronts

Frequency: Annually By: Homeowner Tools needed: Protective gloves, stable work surface

• Assess condition of screen and replace as necessary.

• Inspect for scratches, dents or other damage and repair as necessary.

• Check that louvers are not blocked.

• Vacuum and dust surfaces.

Remote Control

Frequency: Seasonally By: Homeowner Tools needed: Replacement batteries and remote con-

trol instructions.

• Locate remote control transmitter and receiver.

• Verify operation of remote. Refer to remote control operation instructions for proper calibration and setup procedure.

• Place batteries as needed in remote transmitters and battery-powered receivers.

• Place remote control out of reach of children.

If not using your ﬁ replace for an extended period of time (summer months, vacations/trips, etc), to prevent unintended operation:

• Remove batteries from remote controls.

• Unplug 3 volt adapter plug on IPI models.

Page 14

Venting

Frequency: Seasonally By: Homeowner Tools needed: Protective gloves and safety glasses.

• Inspect venting and termination cap for blockage or obstruction such plants, bird nests, leaves, snow, debris, etc.

• Verify termination cap clearance to subsequent construction (building additions, decks, fences, or sheds). See Section 6.

• Inspect for corrosion or separation.

• Verify weather stripping, sealing and ﬂ ashing remains intact.

• Inspect draft shield to verify it is not damaged or missing.

B. Maintenance Tasks-Qualiﬁ ed Service

Technician

The following tasks must be performed by a qualiﬁ ed ser- vice technician.

Gasket Seal and Glass Assembly Inspection

Frequency: Annually By: Qualiﬁ ed Service Technician T ools needed: Protective gloves, drop cloth and a stable

work surface.

• Inspect gasket seal and its condition.

• Inspect ﬁ xed glass assembly for scratches and nicks that can lead to breakage when exposed to heat.

• Conﬁ rm there is no damage to glass or glass frame. Replace as necessary.

• Verify that ﬁ xed glass assembly is properly retained and attachment components are intact and not damaged. Replace as necessary.

Logs

Frequency: Annually By: Qualiﬁ ed Service Technician Tools needed: Protective gloves.

• Inspect for damaged or missing logs. Replace as necessary. Refer to Section 14 for log placement instructions.

• Verify correct log placement and no ﬂ ame impingement causing sooting. Correct as necessary.

Firebox

Frequency: Annually By: Qualiﬁ ed Service Technician Tools needed: Protective gloves, sandpaper, steel wool,

cloths, mineral spirits, primer and touch-up paint.

• Inspect for paint condition, warped surfaces, corrosion or perforation. Sand and repaint as necessary.

• Replace ﬁ replace if ﬁ rebox has been perforated.

Control Compartment and Firebox Top

Frequency: Annually By: Qualiﬁ ed Service Technician Tools needed: Protective gloves, vacuum cleaner, dust

cloths

• V acuum and wipe out dust, cobwebs, debris or pet hair. Use caution when cleaning these areas. Screw tips that have penetrated the sheet metal are sharp and should be avoided.

• Remove all foreign objects.

• Verify unobstructed air circulation.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0814

Page 15

Burner Ignition and Operation

Frequency: Annually By: Qualiﬁ ed Service Technician T ools needed: Protective gloves, vacuum cleaner, whisk

broom, ﬂ ashlight, voltmeter, indexed drill bit set, and a manometer.

• Verify burner is properly secured and aligned with pilot or igniter.

• Clean off burner top, inspect for plugged ports, corrosion or deterioration. Replace burner if necessary.

• Replace ember materials with new dime-size pieces. DO NOT block ports or obstruct lighting paths. Refer to Section 14 for proper ember placement.

• Verify batteries have been removed from battery backup IPI systems to prevent premature battery failure or leaking.

• Check for smooth lighting and ignition carryover to all ports. Verify that there is no ignition delay.

• Inspect for lifting or other ﬂ ame problems.

• Verify air shutter setting is correct. See Section 14 for required air shutter setting. Verify air shutter is clear of dust and debris.

• Inspect oriﬁ ce for soot, dirt and corrosion. Verify oriﬁ ce size is correct. See Service Parts List for proper oriﬁ ce sizing.

• Verify manifold and inlet pressures. Adjust regulator as required.

• Inspect pilot ﬂ ame pattern and strength. See Figure 3.2 for proper pilot ﬂ ame pattern. Clean or replace oriﬁ ce spud as necessary.

• Inspect IPI ﬂ ame sensing rod for soot, corrosion and deterioration. Clean with emery cloth or replace as required.

• Verify that there is not a short in ﬂ ame sense circuit by checking continuity between pilot hood and ﬂ ame sense rod. Replace pilot as necessary.

Figure 3.2 IPI Pilot Flame Patterns

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 15

Page 16

A. Typical Appliance System

NOTICE: Illustrations and photos reﬂ ect typical installations and are for design purposes only . Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual

Getting Started

Installer Guide

HORIZONTAL

TERMINATION CAP

(SECTION 10.G )

FRAMING/HEADER (SECTION 5.B)

NON-COMBUSTIBLE ROOF FLASHING MAINTAINS MINIMUM CLEARANCE AROUND PIPE (SECTION 10.D)

VERTICAL TERMINATION CAP

(SECTION 10.E)

STORM COLLAR (SECTION 10.H)

VENT PIPE PENETRATES ROOF PREFERABLY WITHOUT AFFECTING ROOF RAFTERS (SECTION 8.C )

ATTIC INSULATION SHIELD (NOT SHOWN) MUST BE USED HERE TO KEEP INSULATION AWAY FROM VENT PIPE IF ATTIC IS INSULATED (SECTION 8.D )

VENT PIPE (SECTION 9 and 10)

FRAMING HEADED OFF IN CEILING JOISTS (SECTION 8.C)

CEILING FIRESTOP ON FLOOR OF ATTIC (SECTION 8.C)

Note: Dual venting configurations ARE NOT allowed. Appliance MUST

be vented EITHER vertically OR horizontally.

Figure 4.1 Typical System

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0816

GAS LINE

(SECTION 11.C)

HEARTH EXTENSION

SURROUND

OPTIONAL

WALL SWITCH

MANTEL AND MANTEL LEG (SECTION 5.D)

Page 17

B. Design and Installation Considerations

Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required.

Installation MUST comply with local, regional, state and national codes and regulations. Consult insurance carrier, local building inspector, ﬁ re ofﬁ cials or authorities having jurisdiction over restrictions, installation inspection and permits.

Before installing, determine the following:

• Where the appliance is to be installed.

• The vent system conﬁ guration to be used.

• Gas supply piping.

• Electrical wiring requirements.

• Framing and ﬁ nishing details.

• Whether optional accessories—devices such as a fan, wall switch, or remote control—are desired.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. For assistance or additional information, consult a qualiﬁ ed service technician, service agency or your dealer.

C. Tools and Supplies Needed

Before beginning the installation be sure that the following tools and building supplies are available.

Tape measure Framing material Pliers High temperature caulking material Hammer Phillips screwdriver Gloves Framing square Voltmeter Electric drill and bits (1/4 in.) Plumb line Safety glasses Level Reciprocating saw Manometer Flat blade screwdriver Non-corrosive leak check solution 1/2 - 3/4 in. length, #6 or #8 Self-drilling screws One 1/4 in. female connection (for optional fan).

D. Inspect Appliance and Components

• Carefully remove the appliance and components from the packaging.

• The vent system components and decorative doors and fronts may be shipped in separate packages.

• If packaged separately, the log set and appliance grate must be installed.

• Report to your dealer any parts damaged in shipment, particularly the condition of the glass.

• Read all of the instructions before starting the instal-

lation. Follow these instructions carefully during the installation to ensure maximum safety and beneﬁ t.

WARNING! Risk of Fire or Explosion! Damaged parts could impair safe operation. DO NOT install damaged, incomplete or substitute components. Keep appliance dry.

Hearth & Home T echnologies disclaims any responsibility for , and the warranty will be voided by, the following actions:

• Installation and use of any damaged appliance or vent

system component.

• Modiﬁ cation of the appliance or vent system.

• Installation other than as instructed by Hearth & Home

Technologies.

• Improper positioning of the gas logs or the glass door.

• Installation and/or use of any component part not approved

by Hearth & Home Technologies.

Any such action may cause a ﬁ re hazard.

WARNING! Risk of Fire, Explosion or Electric Shock! DO NOT use this appliance if any part has been under

water. Call a qualiﬁ ed service technician to inspect the appliance and to replace any part of the control system and/or gas control which has been under water.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 17

Page 18

Framing and Clearances

A. Selecting Appliance Location

When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.1).

WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access.

Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and draperies.

36 in.

914 mm

PIER

36 in.

914 mm

NOTICE: Illustrations reﬂ ect typical installations and are FOR DESIGN PURPOSES ONLY. Illustrations/diagrams are not drawn to scale. Actual installation may vary due to individual design preference.

36 in.

914 mm

LCOR

36 in.

914 mm

36 in.

914 mm

36 in.

914 mm

36 in.

914 mm

36 in.

914 mm

36 in.

914 mm

RCOR

Figure 5.1 Appliance Locations

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0818

Page 19

B. Constructing the Appliance Chase

A chase is a vertical box-like structure built to enclose the gas appliance and/or its vent system. In cooler climates the vent should enclosed inside the chase.

NOTICE: Treatment of ceiling ﬁ restops and wall shield ﬁ restops and construction of the chase may vary with the

type of building. These instructions are not substitutes for the requirements of local building codes. Therefore, you MUST check local building codes to determine the requirements to these steps.

Chases should be constructed in the manner of all outside walls of the home to prevent cold air drafting problems. The chase should not break the outside building envelope in any manner.

Walls, ceiling, base plate and cantilever ﬂ oor of the chase should be insulated. Vapor and air inﬁ ltration barriers should be installed in the chase as per regional codes for the rest of the home. Additionally, in regions where cold air inﬁ ltration may be an issue, the inside surfaces may be sheetrocked and taped for maximum air tightness.

To further prevent drafts, the wall shield and ceiling ﬁ re- stops should be caulked with high temperature caulk to seal gaps. Gas line holes and other openings should be caulked with high temp caulk or stuffed with unfaced insulation. If the appliance is being installed on a cement slab, a layer of plywood may be placed underneath to prevent conducting cold up into the room.

C. Clearances

NOTICE: Install appliance on hard metal or wood surfaces extending full width and depth. DO NOT install directly on carpeting, vinyl, tile or any combustible material other than wood.

WARNING! Risk of Fire! Maintain speciﬁ ed air space clearances to appliance and vent pipe:

• Insulation and other materials must be secured to prevent accidental contact.

• The chase must be properly blocked to prevent blown insulation or other combustibles from entering and making contact with ﬁ replace or chimney.

• Failure to maintain airspace may cause overheating and a ﬁ re.

ST-36TRB-IPI

Inches

Millimeters

ABCDEFGHI

DVP Pipe SLP Pipe

Rough

Opening

(Width)

254 219 968 584 1092 803 0 0 13 914

Rough

Opening

(Width)

10 8-5/8 38-1/8 23 43 31-5/8 0 0 1/2 36

Rough

Opening

(Height)

DVP Pipe*

Rough

Opening

(Depth)

Rough

Opening

(Width)

Clearance

to Ceiling

Combustible

Floor

Combustible

Flooring

Ends of

Appliance

Sides of

Appliance

* Adjust framing dimensions for interior sheathing (such as sheetrock)



Figure 5.2 Clearances to Combustibles ST-36TRB-IPI

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 19

Page 20

ABCDEFGHI

DVP Pipe SLP Pipe

PIER-36TRB-IPI

Inches

Millimeters

Rough

Opening

(Width)

Rough

Opening

(Width)

10 8-5/8 38-1/8 23 40 31-5/8 0 0 1/2 36

254 219 968 584 1016 803 0 0 13 914

* Adjust framing dimensions for interior sheathing (such as sheetrock)

Figure 5.3 Clearances to Combustibles PIER-36TRB-IPI



Rough

Opening

(Height)

DVP Pipe*

Rough

Opening

(Depth)

Rough

Opening

(Width)

Clearance

to Ceiling

Combustible

Floor

Combustible

Flooring

Ends of

Appliance

Sides of

Appliance

ABCDEFGHI

RCOR-36TRB-IPI LCOR-36TRB-IPI

Inches

Millimeters

DVP Pipe SLP Pipe

Rough

Opening

(Width)

Rough

Opening

(Width)

Rough

Opening

(Height)

10 8-5/8 38-1/8 24 40 31-5/8 0 0 1/2 36

254 219 968 610 1016 803 0 0 13 914

DVP Pipe*

Rough

Opening

(Depth)

* Adjust framing dimensions for interior sheathing (such as sheetrock)



Figure 5.4 Clearances to Combustibles LCOR-36TRB-IPI and RCOR-36TRB-IPI

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0820

Rough

Opening

(Width)

Clearance

to Ceiling

Combustible

Floor

Combustible

Flooring

Ends of

Appliance

Sides of

Appliance

Page 21

D. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clearances as speciﬁ ed. Framing or ﬁ nishing material closer than the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc).

See-Through Combustible Mantel

TO CEILING

Note: All measurements in inches.

2-1/2

See-Through Non-Combustible Mantel

TO CEILING

Note: All measurements in inches.

Figure 5.7 Minimum Vertical and Maximum Horizontal Dimensions of Non-Combustibles

MAX.

MEASUREMENTS FROM

TOP EDGE OF THE OPENING

MIN.

MEASUREMENTS FROM

TOP EDGE OF THE OPENING

Figure 5.5 Minimum Vertical and Maximum Horizontal Dimensions of Combustibles

PIER/LCOR/RCOR Combustible Mantel

TO CEILING

Note: All measurements in inches.

MEASUREMENTS FROM

TOP EDGE OF THE OPENING

PIER/LCOR/RCOR Non-Combustible Mantel

TO CEILING

MAX.

Note: All measurements in inches.

MEASUREMENTS FROM

TOP EDGE OF THE OPENING

Figure 5.8 Minimum Vertical and Maximum Horizontal Dimensions of Non-Combustibles

MIN.

Figure 5.6 Minimum Vertical and Maximum Horizontal Dimensions of Combustibles

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 21

Page 22

TOP VIEW

1/2 in.

Min.

FIREPLACE

OPENING

2-3/4

in. Min.

1 in.

Unlimited

Max.

3-1/4 in. Min.

Note: Clearance from opening to perpendicular wall.

Figure 5.9 Combustible Mantel Leg or Wall Projections



(Acceptable on both sides of opening)

SHEETROCK

3.5 in.

AIR SPACE REQUIRED

Figure 5.10 Non-Combustible Zone (PIER and ST)

SHEETROCK

3.5 in.

AIR SPACE REQUIRED

Figure 5.11 Non-Combustible Zone (LCOR and RCOR)

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0822

Page 23

Termination Locations

A. Vent Termination Minimum Clearances

WARNING

Fire Risk. Maintain vent clearance to combustibles as

speciﬁ ed.

• DO NOT pack air space with insulation or other materials.

Failure to keep insulation or other materials away from vent pipe may cause overheating and ﬁ re.

HORIZONTAL

OVERHANG

2 FT.

MIN.

GAS DIRECT VENT TERMINATION CAP

20 INCHES MIN.

LOWEST

DISCHARGE

OPENING

VERTICAL

WALL

GAS

TERMINATION

Termination

A B C

DIRECT VENT GAS, WOOD OR FUEL

OIL TERMINATION

Minimum Dimensions

Wood & Fuel Oil

Gas

6 in. 20 in. Horizontal distance between terminations 20 in. 24 in. Distance to perpendicular wall 18 in. 18 in. Vertical distance between terminations

Termination

Comments

ROOF PITCH

IS X/ 12

H (MIN.) - MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE OPENING

Roof Pitch H (Min.) Ft.

Flat to 6/12...........................................................1.0*

Over 6/12 to 7/12 .................................................1.25*

Over 7/12 to 8/12 .................................................1.5*

Over 8/12 to 9/12 .................................................2.0*

Over 9/12 to 10/12 ...............................................2.5

Over 10/12 to 11/12 .............................................3.25

Over 11/12 to 12/12 .............................................4.0

Over 12/12 to 14/12 .............................................5.0

Over 14/12 to 16/12 .............................................6.0

Over 16/12 to 18/12 .............................................7.0

Over 18/12 to 20/12 .............................................7.5

Over 20/12 to 21/12 .............................................8.0

* 3 foot minimum in snow regions

Figure 6.1 Minimum Height From Roof To Lowest Discharge Opening

Figure 6.2 Staggered Termination Caps

DIRECT VENT GAS, WOOD OR FUEL

OIL TERMINATION

(MINIMUM) TO

WOOD OR

GAS TERMINATION

* IF USING DECORATIVE CAP COVER(S), THIS DISTANCE MAY

NEED TO BE INCREASED. REFER TO THE INSTALLATION INSTRUCTIONS SUPPLIED WITH THE DECORATIVE CAP COVER.

20 IN. MIN. *

(508 MM)

PERPENDICULAR

(GAS ONLY)

Figure 6.3 Leveled Termination Caps

20 IN.

(508 MM)

WALL

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 23

Page 24

U.S

(3 FT.)

H OR i

(See Note 2)

Measure vertical clearances from this surface.

Electrical

Service

Measure horizontal clearances from this surface.

= VENT TERMINAL

= AIR SUPPLY INLET

A = 12 inches.................clearances above grade, veranda,

(See Note 1)

porch, deck or balcony

B = 12 inches.................clearances to window or door

that may be opened, or to permanently closed window. (Glass)

C = 18 inches.................vertical clearance to unventilated

sofﬁ t or to ventilated sofﬁ t located above the terminal

30 inches .................for vinyl clad sofﬁ ts and below

electrical service

D = 9 inches..................clearance to outside corner

E = 6 inches...................clearance to inside corner

F = 3 ft. (Canada) ..........not to be installed above a gas

meter/regulator assembly within 3

feet (90 cm) horizontally from the

center-line of the regulator

G = 3 ft ...........................clearance to gas service regulator

vent outlet H = 9 inches (U.S.A.)

12 inches (Canada) clearance to non-mechanical

(See Note 2)

air supply inlet to building or the

combustion air inlet to any other

appliance i = 3 ft. (U.S.A.)

6 ft. (Canada) ...........clearance to a mechanical (pow-

(See Note 2)

** a vent shall not terminate directly above a sidewalk or paved driveway

which is located between two single family dwellings and serves both dwellings.

*** only permitted if veranda, porch, deck or balcony is fully open on a

minimum of 2 sides beneath the ﬂ oor, or meets Note 2.

Note 1: On private property where termination is less than 7 feet above a sidewalk, driveway, deck, porch, veranda or balcony, use of a listed cap shield is suggested. (See vents components page)

Note 2: Termination in a covered alcove space (spaces open only on one side and with an overhang) are permitted with the dimensions speciﬁ ed for vinyl or non-vinyl siding and sofﬁ ts. 1. There must be 3 feet minimum between termination caps. 2. All mechanical air intakes within 10 feet of a termination cap must be a minimum of 3 feet below the termination cap. 3. All gravity air intakes within 3 feet of a termination cap must be a minimum of 1 foot below the termination cap.

Figure 6.4 Minimum Clearances for Termination



ered) air supply inlet

= AREA WHERE TERMINAL IS NOT PERMITTED

J** = 7 ft. ......................... clearance above paved

(See Note 1)

sidewalk or a paved driveway located on public property

K = 6 inches................. clearance from sides of electri-

(See Note 5)

cal service

L = 12 inches................ clearance above electrical

(See Note 5)

service

Covered Alcove Applications

M*** = 18 inches .............clearance under veranda, porch,

42 inches .........vinyl

N = 6 inches ........... non-vinyl sidewalls

12 inches ......... vinyl sidewalls

O = 18 inches ......... non-vinyl sofﬁ t and overhang

42 inches ......... vinyl sofﬁ t and overhang

P = 8 ft.

1 cap 3 feet 2 x Q 2 caps 6 feet 1 x Q 3 caps 9 feet 2/3 x Q 4 caps 12 feet 1/2 x Q

= # termination caps x 3 R

MIN

Note 3: Local codes or regulations may require different

clearances. Note 4: Termination caps may be hot. Consider their proximity to

doors or other trafﬁ c areas. Note 5: Location of the vent termination must not interfere with

access to the electrical service. In the U.S and Canada: Vent system termination is NOT permitted

in screened porches. Vent system termination is permitted in porch areas with two or more

sides open. You must follow all side walls, overhang and ground clearances as stated in the instructions.

Heat & Glo assumes no responsibility for the improper performance of the appliance when the venting system does not meet these requirements.

deck, balcony or overhang

MIN

= (2 / # termination caps) x Q

MAX

ACTUAL

CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE INSTALLED.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0824

Page 25

B. Continue Adding Vent Components

WARNING! Risk of Fire! Installation of this appliance may require the use of heat shield 385-920 above the ﬁ rst 900 elbow in the venting system.

CORRECT INCORRECT

COMBUSTIBLE SURFACE

DIRECTION

To Install the Heat Shield:



1. The heat shield is required above the ﬁ rst elbow if the clearance to combustible surface above is between three (3) and four (4) inches. A shield is not required for clearances greater than four inches. See Figure 6.5.

COMBUSTIBLE

SURFACE

(Required for clearances



between 3 and 4 inches.)

HEAT

SHIELD

3 in. MIN

(76 mm)

HEAT SHIELD

90º ELBOW

Figure 6.6

• If the combustible materials are not in place at the time of install the elbow heat shield may be screwed to the exhaust pipe (see Figure 6.7). Cut the tabs as shown and bend down. Secure the heat shield to the pipe maintaining 3 inch to 4 inch between the pipe and shield.

SCREW

3 in.

(76 mm)

Figure 6.5

2. Fasten the shield in place using the four pilot holes provided in the part. The shield should be oriented such that the 13-1/8 inch dimension (longest dimension) is running in the same direction the elbow is pointing. The shield should be centered directly above the elbow, and positioned so that it creates a 1/2 inch airspace between the shield and the combustible surface. See Figure 6.6.

Figure 6.7

Refer to Cinch Pipe and Termination Cap installation instructions.

• Continue adding vent components, locking each succeeding component into place.

• Ensure that each succeeding vent component is securely ﬁ tted and locked into the preceding component in the vent system.

• 90º elbows may be installed and rotated to any point around the preceding component’s vertical axis. If an elbow does not end up in a locked position with the preceding component, attach with a minimum of two (2) sheet metal screws.

C. Install Support Brackets

Refer to cinch pipe and termination cap installation instructions.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 25

Page 26

Vent Information and Diagrams

A. Approved Pipe

This appliance is approved for use with Hearth & Home Technologies a DVP venting system. Refer to Section 16B for vent component information.

DO NOT mix pipe, ﬁ ttings or joining methods from differ- ent manufacturers.

The pipe is tested to be run inside an enclosed wall. There is no requirement for inspection openings at each joint within the wall.

WARNING! Risk of Fire or Asphyxiation. This appliance requires a separate vent. DO NOT vent to a pipe serving a separate solid fuel burning appliance.

Vertical

12 in.

8-1/2 in.

B. Vent Table Key

The abbreviations listed in this vent table key are used in the vent diagrams.

Symbol Description

First section (closest to appliance) of vertical length

Second section of vertical length

First section (closest to appliance) of horizontal length

Subsequent sections of horizontal length

C. Use of Elbows

Diagonal runs have both vertical and horizontal vent aspects when calculating the effects. Use the rise for the vertical aspect and the run for the horizontal aspect (see Figure 7.1).

Two 45º elbows may be used in place of one 90º elbow. On 45º runs, one foot of diagonal is equal to 8-1/2 in. (216 mm) horizontal run and 8-1/2 in. (216 mm) vertical run. A length of straight pipe is allowed between two 45º elbows (see Figure 7.1).

Horizontal

Figure 7.1

D. Measuring Standards

Vertical and horizontal measurements listed in the vent diagrams were made using the following standards.

• Pipe measurements are shown using the effective length

of pipe (see Figure 7.2).

• Horizontal terminations are measured to the outside

mounting surface (ﬂ ange of termination cap) (see Figure

6.1).

• Vertical terminations are measured to bottom of

termination cap.

• Horizontal pipe installed level with no rise.

Effective Length

Inches Millimeters

Effective

Height/Length

Pipe

DVP4 4 102

DVP6 6 152 DVP12 12 305 DVP24 24 610 DVP36 36 914 DVP48 48 1219 DVP6A 3 to 6 76 to 152

DVP12A 3 to 12 76 to 305 DVP12MI 3 to 12 76 to 305 DVP24MI 3 to 24 76 to 610

Figure 7.2 DVP Pipe Effective Length

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0826

Page 27

E. Vent Diagrams

To replace the ﬁ rst starter elbow with two 45° elbows, refer to Figure 7.3. All other 90° elbows can be replaced with two 45° elbows.

General Rules:

• A maximum of three 90° elbows (or six 45° elbows) may be used in any vent conﬁ guration. Some elbows may be installed horizontally. See Figure 7.6.

• Elbows may be placed back to back anywhere in the system as long as the ﬁ rst 90° elbow is a starter elbow except as shown in Figure 7.3.

• When penetrating a combustible wall, a wall shield ﬁ restop must be installed.

• When penetrating a combustible ceiling, a ceiling ﬁ restop must be installed.

• Horizontal runs of vent do not require vertical rise; horizontal runs may be level.

Note: The Multi-Sided series ﬁ replaces can adapt

to SLP series vent pipe, if desired.

When venting off the top of the unit, attach a DVP-2SL adapter to the appliance starting collar, immediately followed by a minimum 48 inch vertical section of SLP series vent pipe.

After the 48 inch vertical section, the venting table rules must be followed. The ﬁ rst 48 inch vertical section is NOT counted as part of the vertical components in the table. It is still counted as part of the overall maximum run. All venting table rules for the vent run must still be followed.

Example:

SLP pipe 7 ft. min. vertical = 11 ft. max. horizontal

DVP pipe 3 ft. min. vertical = 11 ft. max. horizontal

Top Vent—Horizontal Termination—Two 45° Elbows Installation requirements to replace the ﬁ rst 90° elbow with two 45° elbows:

4 ft min. (1.22 m)

16 ft max.

(4.87 m)

Note: Reference Figure 7.14 for special instructions for use of 45º elbow on rear vent appliances.

Figure 7.3 Minimum Installation Requirements for Two 45° Elbows-Top Vent-Horizontal Termination

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 27

Page 28

1. Top Vent - Horizontal Termination - (continued)

One Elbow

Figure 7.4

Two Elbows

V1 Minimum H1 Maximum

Elbow only 1-1/2 ft. 457 mm

6 in. 152 mm 2-1/2 ft. 610 mm

1 ft. 305 mm 3 ft. 914 mm 2 ft. 610 mm 6 ft 1.8 m 3 ft. 914 mm 9 ft. 2.7 m

4 ft. 1.2 m 12 ft. 3.7 m 5 ft. 1.5 m 15 ft. 4.6 m 6 ft. 1.8 m 18 ft. 5.5 m

V1 + H1 = 50 ft. (15.2 m) Maximum

H1 = 18 ft. (5.5 m) Maximum



V1 Minimum H1 + H2 Maximum

Elbow only 6 in. 152 mm 1 ft. 305 mm 2 ft. 610 mm 2 ft. 610 mm 4 ft. 1.2 m 3 ft. 914 mm 9 ft. 2.7 m

4 ft 1.2 m 12 ft. 3.7 m 5 ft. 1.5 m 15 ft. 4.6 m 6 ft. 1.8 m 18 ft. 5.5 m

+ H1 + H2 = 50 ft. (15.2 m) Maximum

H1 + H2 = 18 ft. (5.5 m) Maximum

Figure 7.5

INSTALLED

HORIZONTALLY

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0828

Page 29

1. Top Vent - Horizontal Termination - (continued)

Three Elbows

V1 Minimum H1 Maximum V2 Minimum H2 Maximum V1 + V2 Minimum H1 + H2 Maximum



Elbow only 1 ft. 305 mm 6 in. 152 mm 1 ft. 305 mm 6 in. 152 mm 1 ft. 305 mm

6 in. 152 mm 3 ft. 914 mm 6 in. 152 mm 2 ft. 610 mm 1 ft. 305 mm 3 ft. 914 mm

1 ft. 305 mm 6 ft 1.8 m 1 ft. 305 mm 6 ft 1.8 m 2 ft. 610 mm 12 ft. 3.7 m 2 ft. 610 mm 10 ft.* 3 m 2 ft. 610 mm 10 ft.* 3 m 4 ft 1.2 m 18 ft. 5.5 m

3 ft. 914 mm 12 ft.* 3.7 m 3 ft. 914 mm 12 ft.* 3.7 m 6 ft 1.8 m

+ H2 = 18 ft. (5.5 m) Maximum V1 + V2 + H1 + H2 = 50 ft. (15.2 m) Maximum

18 ft 5.5 m

Figure 7.6

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 29

Page 30

2. Top Vent - Vertical Termination No Elbow

V1 = 60 ft. Max. (18.3 m)

V1 = 3 ft. Min. (914 mm)

NOTE: If installing a vertical vent/

termination off the top of the appliance, the optional vertical termination bafﬂ e should be used.

Exhaust restrictor Instructions

1. Remove refractory panel and exhaust bafﬂ e from pilot side of appliance. Use a 1/4 inch nut driver and remove the two screws that secure it in place. To remove the exhaust bafﬂ e, remove the three screws securing the refractory panel in place. See Figure 7.8.

Refractory Panel

To access the exhaust opening, remove the refractory panel and exhaust baffle. To remove refractory panel, remove the two screws on top. To remove the exhaust baffle, remove the three screws securing it.

Figure 7.7

Exhaust restrictors are recommended for these vertically terminated products which have excessive draft. Exhaust restrictors will compensate for high draft, and restore visual ﬂ ame height. If the vent conﬁ guration has a total vertical of 15-60 feet, an exhaust restrictor may be needed. The exhaust restrictor can be located in the appliance manual bag.

Top Vent Application

Exhaust restrictor

Note:Besuretoreinstall the exhaust baffle and refractory panel after exhaust restrictor installation.

Rear Vent Application

Exhaust restrictor

Note: Be sure to reinstall the e x h a u s t baffle and refractory panel after exhaust restrictor installation.

Figure 7.8

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0830

Page 31

2. Break the exhaust restrictor into two pieces. Do this by bending the part back and forth until it breaks (see Figure 7.9).

BREAK

HERE

4. Center the exhaust restrictor in the open end of the exhaust outlet and secure through the slots on the exhaust restrictor with the 2-1/4 in. self tapping screws provided in the appliance manual bag.

5. Reinstall the refractory panel.

1 2 3 4 5

SETTINGS

Figure 7.9 Exhaust Restrictor

3. Match the amount of vertical you have in the system with the chart to ﬁ nd the appropriate position to set the exhaust restrictor (see Figure 7.10).

Vertical

4 ft. 1-1

8 ft. 2-2 1-2 1-1

15 ft. 3-3 3-2 2-2 1-2

20 ft. 3-4 3-3 3-3 2-3

25 ft. 3-4 3-3 3-3 2-3

30 ft. 4-4 3-4 3-4 3-3

35 ft. 4-4 3-4 3-4 3-3

40 ft. 5-4 4-4 4-4 3-4

TOP VENT REAR VENT

NG LP NG LP

RestrictorNoRestrictorNoRestrictor

Restrictor

1 2 3 4 5

Figure 7.10

45 ft. 5-4 4-4 4-4 3-4

50 ft. 5-5 5-4 5-4 4-4

55 ft. 5-5 5-4 5-4 4-4

Note: If the DVP-2SL adapter and SLP pipe is used, you

MUST subtract one number from the table above.

Example: Top vent 40 ft vertical with DVP pipe = 5-4

Top vent 40 ft vertical with SLP pipe = 4-3

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 31

Page 32

Two Elbows

Figure 7.11

V1 H

Maximum V

V1 + V2 Minimum



One Elbow 2-1/2 ft. 762 mm * * * 2 ft. 607 mm 6 ft. 1.8 m * * * 4 ft. 1.2 m 12 ft. 3.7 m * * * 6 ft. 1.8 m 18 ft. 5.5 m

+ V2 + H1 = 50 ft (15.2 m) Maximum

*No speciﬁ c restrictions on this value EXCEPT

V1 + V2 + H1 cannot exceed 50 ft (15.2 m)

Three Elbows

+ H2 V2V1 + V2 Minimum H1+ H2 Maximum



ELBOW ONLY 1 ft. 305 mm * * * 1 ft. 305 mm

1 ft. 305 mm 2 ft. 610 mm * * * 2 ft. 610 mm 2 ft. 610 mm 4 ft 1.2 m * * * 4 ft 1.2 m 3 ft. 914 mm 9 ft. 2.7 m * * * 9 ft. 2.7 m

4 ft 1.2 m 12 ft. 3.7 m * * * 12 ft. 3.7 m

6 ft. 1.8 m 18 ft. 5.5 m * * * 18 ft. 5.5 m

+ H2 = 18 ft (5.5 m) Maximum

*No speciﬁ c restrictions on this value EXCEPT

V1+ V2 + H1+ H2 cannot exceed 50 ft (15.2 m)

Figure 7.12

INSTALLED

HORIZONTALLY

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0832

Page 33

3. Rear Vent - Horizontal Termination

No Elbow

= 18 in. (406 mm) Maximum

Figure 7.13

One 45° Elbow

DO NOT use a 45º elbow

in corner installations. Use two 90º elbow instead.

Figure 7.14

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 33

Page 34

3. Rear Vent - Horizontal Termination - (continued)

Two Elbows

H1 Maximum V1 Minimum H2 Maximum H1+ H2 Maximum



2 ft. 610 mm 6 in. 152 mm 1 ft. 305 mm 1 ft 305 mm 3 ft. 914 mm 1 ft. 305 mm 2 ft. 610 mm 3 ft. 914 mm 3 ft. 914 mm 2 ft. 610 mm 4 ft 1.2 m 6 ft. 1.8 m 3 ft. 914 mm 3 ft. 914 mm 7 ft. 2.1 m 9 ft. 2.7 m 3 ft. 914 mm 4 ft. 1.2 m 10 ft. 3 m 12 ft. 3.7 m 3 ft. 914 mm 5 ft. 1.5 m 12 ft. 3.7 m 15 ft. 4.6 m 3 ft. 914 mm 6 ft. 1.8 m 15 ft. 4.6 m 18 ft. 5.5 m

+ H1+ H2= 50 ft (15.2 m) Maximum H1= 3 ft (914 mm) Maximum

*H1+ H2= 18 ft (5.5 m) Maximum

Figure 7.15

Three Elbows

INSTALLED

HORIZONTALLY

Maximum V1 Minimum H2+ H

H1+ H2+ H3 Maximum



6 in. 152 mm 6 in. 152 mm 6 in. 152 mm 1 ft. 305 mm

1 ft. 305 mm 1 ft. 305 mm 2 ft. 610 mm 3 ft. 914 mm 3 ft. 914 mm 2 ft. 610 mm 3 ft. 914 mm 6 ft. 1.8 m 3 ft. 914 mm 3 ft. 914 mm 6 ft. 1.8 m 9 ft. 2.7 m 3 ft. 914 mm 4 ft. 1.2 m 9 ft. 2.7 m 12 ft. 3.7 m

+ H1+ H2+ H3= 40 ft (12.2 m) Maximum H1= 3 ft (94 mm) Maximum

+ H2+ H3= 12 ft (3.7 m) Maximum

Figure 7.16

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0834

Page 35

4. Rear Vent - Vertical Termination

One Elbow

Figure 7.17

V1 Minimum H1 Maximum



1 ft. 305 mm 3 ft. 914 mm 2 ft. 610 mm 5 ft. 1.5 m 3 ft. 914 mm 7 ft. 2.1 m 4 ft. 1.2 m 8 ft 2.4 m 5 ft. 1.5 m 8 ft 2.4 m

+ H1 = 40 ft (12.2 m) Maximum

Two Elbows

Minimum H1 + H2 Maximum



Back to Back 90° Elbows 3 ft. 914 mm

2 ft 610 mm 6 ft. 1.8 m

4 ft. 1.2 m

9 ft. 2.7 m 5 ft. 1.5 m 10 ft. 3 m 6 ft. 1.8 m 12 ft. 3.7 m

V1+ H1 + H2= 50 ft (15.2 m) Maximum

+ H2= 16 ft (4.9 m) Maximum

INSTALLED

HORIZONTALLY

Figure 7.18

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 35

Page 36

4. Rear Vent - Vertical Termination - (continued)

Three Elbows

Maximum V1 Minimum H

H1+ H2 Maximum



1 ft. 305 mm 1 ft. 305 mm 1 ft. 305 mm 2 ft. 610 mm 2 ft. 610 mm 2 ft. 610 mm 3 ft. 914 mm 5 ft. 1.5 m 4 ft. 1.2 m 3 ft. 914 mm 4 ft. 1.2 m 8 ft. 4.6 m 5 ft. 1.5 m 4 ft. 1.2 m 6 ft. 1.8 m 11 ft. 3.4 m

6 ft. 1.8 m 5 ft. 1.5 m 8 ft. 2.4 m 14 ft. 4.3 m 8 ft. 2.4 m 6 ft. 1.8 m 9 ft. 2.7 m 17 ft. 5.2 m

= 8 ft (2.4 m) Max. V1+ V2+ H1+ H2= 50 ft (15.2 m) Max.

H1+ H2= 17 ft (5.2 m) Max.

Figure 7.19

Three Elbows

H1H2H

V1 Minimum H1+ H2+ H3 Maximum



***8 ft. 2.4 m 4 ft. 1.2 m ***9 ft. 2.7 m 5 ft. 1.5 m ***10 ft. 3.1 m 6 ft. 1.8 m

*No speciﬁ c restrictions on this value EXCEPT

+ H1+ H2+ H3 cannot exceed 50 ft. (15.2 m) Maximum

H1+ H2+ H3 = 6 ft. (1.8 m) Maximum

Figure 7.20

INSTALLED

HORIZONTALLY

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0836

Page 37

Vent Clearances and Framing

A. Pipe Clearances to Combustibles

WARNING! Risk of Fire! Maintain air space clearance to vent. DO NOT pack insulation or other combustibles:

• Between ceiling ﬁ restops

• Between wall shield ﬁ restops

• Around vent system Failure to keep insulation or other material away from

vent pipe may cause over heating and ﬁ re.

Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).

• DVP heat shield - designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick.

• If wall thickness is less than 4 in. the existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. a DVP-HSM-B will be required.

• SLP heat shield - designed to be used on a wall 4-3/8 in. to 7-5/8 in. (111 mm to 194 mm thick).

• If wall thickness is less than 4-3/8 the existing heat shields must be field trimmed. If wall thickness is greater than 7-5/8 in. a DVP-HSM-B will be required.

(DVP-SLP Pipe Shown)

3 in. (76 mm) top clearance

1 in. (25 mm) clearance around vertical sections

Heat Shield

Wall

Shield

Firestop

3 in. (76 mm) top clearance *

Heat Shield

1 in. (25 mm) clearance bottom & sides

B. Wall Penetration Framing

Combustible Wall Penetration

Whenever a combustible wall is penetrated, you must frame a hole for the wall shield ﬁ restop(s). The wall shield ﬁ restop maintains minimum clearances and prevents cold air inﬁ ltration.

• The opening must be framed on all four sides using the same size framing materials as those used in the wall construction.

• SLP pipe - A wall shield ﬁ restop must be placed on each side of an interior wall. A minimum 1-1/2 in. (38 mm) overlap of attached heat shields must be maintained.

• DVP pipe - A wall shield ﬁ restop is required on one side only on interior walls. If your local inspector requires a wall shield ﬁ restop on both sides, then both wall shield ﬁ restops must have a heat shield (refer to Section 16.B.) attached to them.

• See Section 8.M. for information for regarding the installation of a horizontal termination cap.

Non-Combustible Wall Penetration

If the hole being penetrated is surrounded by noncombustible materials such as concrete, a hole with diameter one in. greater than the pipe is acceptable.

Whenever a non-combustible wall is penetrated, the wall shield ﬁ restop is only required on one side and no heat shield is necessary.

WALL

3 in. (76 mm) top clearance *

Heat Shield

1 in. (25 mm) clearance bottom & sides

Heat Shield

Wall

Shield

Firestop

* When using SLP pipe, minimum clearances from the vent pipe to combustible materi-

als at wall shield firestops are: T op: 2-1/2 in. (64 mm) Bottom: 1/2 in. (13 mm) Sides: 1 in. (25 mm)

Figure 8.1 Horizontal Venting Clearances To Combustible Materials

10 in.

A* B* C D

43-3/4 in. 28 in. 42-3/4 in. 27 in.

* Shows center of vent framing hole for top or rear venting. The center of the

hole is one (1) inch (25.4 mm) above the center of the horizontal vent pipe.

Figure 8.2 Wall Penetration

12 in.

Note: When venting off the top of the unit using SLP pipe, a 10 in. x 10 in. framing hole is required.



Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 37

Page 38

C. Vertical Penetration Framing

A ceiling ﬁ restop MUST be used between ﬂ oors and attics.

• DVP pipe only - Frame an opening 10 in. by 10 in. (254 mm by 254 mm) whenever the vent penetrates a ceiling/ﬂ oor (see Figure 8.3).

• SLP pipe only - Frame opening 9 in. x 9 in. (229 mm x 229 mm) whenever the vent penetrates a ceiling/ﬂ oor (see Figure 8.3).

• Frame the area with the same sized lumber as used in ceiling/ﬂ oor joist.

• The ceiling ﬁ restop may be installed above or below the ceiling joists when installed with a attic insulation shield. It must be under joists between ﬂ oors that are not insulated. Refer to Figure 8.4.

• Secure with three fasteners on each side.

WARNING! Risk of Fire! DO NOT pack insu-

lation around the vent. Insulation must be kept back from the pipe to prevent overheating.

ATTIC ABOVE

Figure 8.3

PIPE DVP SLP

INSTALL ATTIC INSULATION SHIELDS

BEFORE OR AFTER INSTALLATION OF VENT SYSTEM

3 FASTENERS

PER SIDE

10 in. (254 mm)

9 in. (229 mm)

CEILING FIRESTOP

INSTALLED BELOW CEILING

Figure 8.4 Installing the Attic Shield

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0838

CEILING FIRESTOP

INSTALLED ABOVE CEILING

Page 39

D. Install Attic Insulation Shield

WARNING! Fire Risk. DO NOT allow loose materials or insulation to touch vent. Hearth & Home Technologies Inc. requires the use of an attic shield.

The National Fuel Gas Code ANSI Z223.1 and NFPA 54 requires an attic shield constructed of 26 gauge minimum metal that extends at least 2 in. (51 mm) above insulation.

Attic shields must meet speciﬁ ed clearance and be se- cured in place.

Flat Ceiling Installation

• Remove one shield from box.

NOTICE: Cut previously installed batt insulation to make room for the attic insulation shield.

• Wrap shield around pipe if pipe is already installed in area to be insulated.

• Match the three holes in each side and fasten with three screws to form a tube.

• Bend three tabs on the bottom of the shield outward to allow attachment to the ceiling ﬁ restop.

• Bend the remaining bottom tabs inward 90° to maintain the air space between the pipe and the shield. Set the shield on the ceiling ﬁ restop and attach to the ﬁ restop.

• Bend all tabs inward 90° around the top of the shield. These tabs must be used to prevent blown insulation from getting between the shield and vent pipe, and to maintain air space clearance.

BEND ALL TABS INWARD 90° TO MAINTAIN CLEARANCE AND PREVENT INSULATION FROM FALLING INSIDE

INSERT 3 SCREWS

Figure 8.5 Attic Insulation Shield

LASER-ETCHED CUT LINES

BEND 3 TABS OUTWARD TO FASTEN TO CEILING FIRESTOP-BEND REMAINING TABS INWARD 90 DEGREES TO MAINTAIN CLEARANCE

Vaulted Ceiling Installation

• The attic insulation shield has been laser-etched with cut lines and ceiling pitches to make ﬁ eld trimming easier.

• Remove one shield from box.

NOTICE: Cut previously installed batt insulation to make room for the attic insulation shield.

• Cut the attic insulation shield (if application is for vaulted ceiling) using a laser-etched cut line, to ﬁ t your ceiling pitch. Snip cut edge to recreate 1 in. bend tabs all the way around the bottom.

• Wrap shield around pipe if pipe is already installed in area to be insulated.

• Match the three holes in each side and fasten with three screws to form a tube.

• Bend three tabs on the bottom of the shield outward to allow attachment to the ceiling ﬁ restop.

• Bend the remaining bottom tabs inward 90° to maintain the air space between the pipe and the shield. Set the shield on the ceiling ﬁ restop and attach to the ﬁ restop.

• Bend all tabs inward 90° around the top of the shield. These tabs must be used to prevent blown insulation from getting between the shield and vent pipe, and to maintain air space clearance.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 39

Page 40

Appliance Preparation

A. Top Vent

CAUTION! Risk of Cuts, Abrasions or Flying Debris.

Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

NOTICE: Once appliance is set up for top or rear venting, it CANNOT be changed at a later time.

Figure 9.1 Remove the elbow heat shield by removing the four screws holding it to the top of the appliance. Refer to Section 6B to determine if the elbow heat shield is required.

NOTICE: Once the vent cap has been removed it CANNOT be reattached.

Figure 9.3 Fold the center parts of the retaining band up and use to remove the vent cap.

Figure 9.2 Cut the metal retaining band and fold the sides out.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0840

Figure 9.4 Remove and discard the seal cap, insulation donut, insulation plug, and the insulation basket. Attach the ﬁ rst vent section (it will snap into place). Slide the vent gasket onto the vent section and then, up against the appliance. Secure the vent gasket to the appliance with two self-tapping screws found in the manual bag. Note: The vent gasket can found in the manual bag.

Proceed to Section 9. C.

Page 41

B. Rear Vent

NOTICE: Once appliance is set up for top or rear venting, it CANNOT be changed at a later time.

Figure 9.5 Cut the metal retaining band.

NOTICE: Once the vent cap has been removed it CANNOT be reattached.

Figure 9.7 Discard the seal cap, insulation plug and the insulation basket.

Figure 9.6 Remove the seal cap.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 41

Figure 9.8 Attach the ﬁ rst vent section (it will snap into place). Slide the vent gasket onto the vent section and then, up against the appliance. Secure the vent gasket to the appliance with two self-tapping screws found in the manual bag. Note: The vent gasket can found in the manual bag.

Page 42

C. Securing and Leveling the Appliance

WARNING! Risk of Fire! Prevent contact with:

• Sagging or loose insulation

• Insulation backing or plastic

• Framing and other combustible materials Block openings into the chase to prevent entry of blown-

in insulation. Make sure insulation and other materials are secured.

DO NOT notch the framing around the appliance standoffs.

Failure to maintain air space clearance may cause overheating and ﬁ re.

NOTICE: Failure to ensure that the ﬁ replace opening is square may result in the decorative front not ﬁ tting properly.

6. Bend out nailing tabs on each side making sure to keep the nailing tabs ﬂ ush with the framing.

7. Using a framing square, make sure that the sides of the appliance are square to the bottom as shown in Figure 9.10.

The diagram shows how to properly position, level, and secure the appliance (see Figure 9.9). Nailing tabs are provided to secure the appliance to the framing members.

1. Venting - refer to V ent Clearances and Framing (Section

8) for hole location.

2. When installing a LCOR or RCOR ﬁ replace remove the nailing tab located on the side of the unit and reattach it to the front corner of the unit as shown in Figure 9.8 (R-COR).

90º

SID

E TO SIDE

FRONT TO BACK

Figure 9.9 Proper Positioning and Leveling of an Appliance

8. Secure the appliance to the framing by using nails or screws through the nailing tabs. It is acceptable to use plumber strap to secure the unit to the framing if necessary. See Figure 9.10. Be sure to maintain all clearances to combustible material.

Figure 9.8 Attach Nailing Tab to Front Corner of Unit



3. Place the appliance into position, making sure to maintain proper clearance to combustibles.

4. Level the appliance from side to side and front to back. It is acceptable to use wood shims under the appliance.

5. Fasten the appliance to the ﬂ oor using the pilot holes located at the bottom of the appliance.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0842

NAILING TABS

Figure 9.10 Securing An Appliance

Note: Once appliance is setup for top or rear venting, it

CANNOT be changed at a later time.

Page 43

Lances

Installing Vent Pipe (DVP and SLP Pipe)

A. Assemble Vent Sections (DVP Pipe Only)

Attach Vent to the Firebox Assembly

Note: The end of the pipe sections with the lanced tabs will face

toward the appliance.

Attach the ﬁ rst pipe section to the starting collar:

• Lanced pipe end to the starting collar

• Inner pipe over inner collar

• Push the pipe section until all lanced tabs snap in place

• Lightly tug on pipe to conﬁ rm it has locked.

Commercial, Multi-family (Multi-level exceeding two stories), or High-Rise Applications

All outer pipe joints must be sealed with high temperature silicone, including the slip section that connects directly to the horizontal termination cap.

• Apply a bead of silicone sealant inside the female outer

pipe joint prior to joining sections. See Figure 10.1

• Only outer pipes need to be sealed. All unit collar, pipe,

slip section, elbow and cap outer ﬂ ues shall be sealed in this manner, unless otherwise stated.

Figure 10.1 High Temperature Silicone Sealant

Lances

WARNING! Risk of Fire or Explosion! DO NOT break silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals are broken during removal of the termination cap, vent may leak.

Assemble Pipe Sections (DVP Pipe Only)

Per Figure 10.2:

• Start the inner pipe on the lanced end of section A into

the ﬂ ared end of section B.

• Start the outer pipe of section A over the outer pipe of

section B.

• Once both vents sections are started, push ﬁ rmly until

all lanced tabs lock into place.

• Lightly tug on the pipe to conﬁ rm the tabs have locked.

It is acceptable to use screws no longer than 1/2 in. (13 mm) to hold outer pipe sections together. If predrilling holes, DO NOT penetrate inner pipe.

For 90° and 45° elbows that are changing the vent direction from horizontal to vertical, one screw minimum should be put in the outer ﬂ ue at the horizontal elbow joint to prevent the elbow from rotating. Use screws no longer than 1/2 in. (13 mm). If predrilling screw holes, DO NOT penetrate inner pipe.

Figure 10.2

Note: Make sure that the seams are not aligned to prevent

unintentional disconnection.

CORRECT

Figure 10.3

Figure 10.4 Seams

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 43

INCORRECT

Page 44

B. Assemble Vent Sections (SLP Pipe Only)

Pilot hole

To attach the ﬁ rst vent component to the starting collars of the appliance:

• Attach an SLP-DVP24 adapter to the starting collar of

the appliance.

• Lock the vent components into place by sliding the pipe

section onto the collar.

• Align the seam of the pipe and seam of collar to allow

engagement. Rotate the vent component to lock into place. Use this procedure for all vent components. See Figure 10.5.

• Slide the gasket over the ﬁ rst vent section and place it

ﬂ ush to the appliance. This will prevent cold air inﬁ ltration. High temperature caulk may be used to hold the part in place.

• Continue adding vent components, locking each

succeeding component into place.

• Ensure that each succeeding vent component is securely

ﬁ tted and locked into the preceding component.

Commercial, Multi-family (Multi-level exceeding two stories), or High-Rise Applications

For Installation into a commercial, multi-family (multi-level exceeding two stories) or high-rise applications: All outer pipe joints must be sealed with high temperature silicone, including the slip section that connects directly to the horizontal termination cap.

• Apply a bead of silicone sealant inside the female outer

pipe joint prior to joining sections. See Figure 10.1.

• Only outer pipes need to be sealed. All unit collar, pipe,

slip section, elbow and cap outer ﬂ ues shall be sealed in this manner, unless otherwise stated.

C. Assemble Slip Sections

• Slide the inner ﬂ ue of the slip section into the inner ﬂ ue of the pipe section and the outer ﬂ ue of the slip section over the outer ﬂ ue of the pipe section. See Figure 10.6.

• Slide together to the desired length.

Pilot hole

Figure 10.6 Slip Section Pilot Holes

• Maintain a 1-1/2 in. (38 mm) overlap between the slip section and the pipe section.

• Secure the pipe and slip section with two screws no longer than 1/2 in. (13 mm), using the pilot holes in the slip section. See Figure 10.7.

Note: Align seams to engage pipe, then rotate counterclockwise to lock

Figure 10.5 Adding Venting Components

Figure 10.7 Screws into Slip Section

• Continue adding pipe as necessary following instructions in “Assembling Pipe Sections.”

NOTICE: If slip section is too long, the inner and outer ﬂ ues of the slip section can be cut to the desired length.

NOTICE: When installing a vent system with an HRC termination cap, all pipe system joints shall be sealed using a high temperature silicone sealant.

• Apply a bead of silicone sealant inside the female outer pipe joint prior to joining sections.

• Only outer pipes are sealed, sealing the inner ﬂ ue is not required.

• All unit collar, pipe, slip section, elbow and cap outer ﬂ ues shall be sealed.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0844

Page 45

D. Secure the Vent Sections

• Vertical runs of DVP pipe must be supported every 8 ft. (2.44 m) after the 25 ft. (7.62 m) maximum unsupported rise.

• Vertical runs of SLP pipe must be supported every 8 ft. (2.44 m).

• Horizontal sections must be supported every 5 feet (1.52 m).

• Vent supports or plumbers strap (spaced 120º apart) may be used to support. See Figures 10.8 and 10.9.

• Wall shield ﬁ restops may be used to provide horizontal support.

• SLP ceiling ﬁ restops have tabs that may be used to provide vertical support.

WARNING! Risk of Fire, Explosion or Asphyxiation!

Improper support may allow vent to sag and separate. Use vent run supports and connect vent sections per installation instructions. DO NOT allow vent to sag below connection point to appliance.

E. Disassemble Vent Sections

• Rotate either section (see Figure 10.10) so the seams on both pipe sections are aligned as shown in Figure

10.11.

• Pull carefully to separate the pieces of pipe.

Figure 10.10 Rotate Seams for Disassembly

120º

Figure 10.8 Securing Vertical Pipe Sections

120º

Figure 10.11 Align and Disassemble Vent Sections

Figure 10.9 Securing Horizontal Pipe Sections

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 45

Page 46

F. Install Decorative Ceiling Components

(SLP only)

A decorative ceiling thimble can be installed on a ﬂ at ceil- ing through which the vent passes. The decorative ceiling thimble is used to cover the ﬁ restop.

• Seal the gap between the vent pipe and ﬁ restop using high temperature silicone to prevent cold air inﬁ ltration.

• Install the decorative ceiling thimble by sliding it up to the ceiling and attaching it using the provided screws.

A decorative cathedral ceiling support box can be installed on a cathedral ceiling through which the vent passes.

• Use a plumb-bob to mark the center line of the venting system on the ceiling and drill a small hole through the ceiling and roof at this point. Locate the hole and mark the outline of the cathedral ceiling support box on the outside roof.

• Remove shingles or other roof covering as necessary to cut the rectangular hole for the support box. Cut the hole 1/8 in. (3 mm) larger than the support box outline.

• Lower the support box through the hole in the roof until its bottom is at least 2 in. (51 mm) below the ceiling (Figure

10.12).

• Level the support box both vertically and horizontally and temporarily tack it in place through the inside walls into the roof sheathing.

• Use tin snips to cut the support box from the top corners down to the roof line and fold the resulting ﬂ aps to the roof. See Figure 10.13.

• Nail the ﬂ aps to the roof AFTER running a bead of non hardening sealant between the ﬂ aps and the roof.

WARNING! Risk of Fire! Clean out ALL materials from inside the support box and complete the vertical vent run and termination.

LEVEL

CATHEDRAL CEILING SUPPORT BOX

2 in. (51 mm) MIN. BELOW FINISHED CEILING

CUT HOLE 1/8 in. (3 mm) GREATER IN SIZE THAN PATTERN OF SUPPORT BOX AS IT IS PROJECTED ONTO ROOF LINE

Figure 10.12

Figure 10.13

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0846

Page 47

G. Install Metal Roof Flashing

Figure 10.16 Assembling the Storm Collar

Figure 10.17 Assembling the Storm Collar Around the Pipe

Figure 10.15

Note: Skip this section if using the RF4-8.

• See minimum vent heights for various pitched roofs (Figure 10.14) to determine the length of pipe to extend through the roof.

• Slide the roof ﬂ ashing over the pipe sections extending through the roof as shown in Figure 10.15.

HORIZONTAL

OVERHANG

CAULK

2 FT.

MIN.

GAS DIRECT VENT TERMINATION CAP

Roof Pitch H (Min.) Ft.

Flat to 6/12........................................1.0*

Over 6/12 to 7/12 ............................1.25*

Over 7/12 to 8/12 ..............................1.5*

Over 8/12 to 9/12 ..............................2.0*

Over 9/12 to 10/12 ............................. 2.5

Over 10/12 to 11/12 ......................... 3.25

Over 11/12 to 12/12 ........................... 4.0

Over 12/12 to 14/12 ........................... 5.0

Over 14/12 to 16/12 ........................... 6.0

Over 16/12 to 18/12 ........................... 7.0

Over 18/12 to 20/12 ........................... 7.5

Over 20/12 to 21/12 ........................... 8.0

20 INCHES MIN.

LOWEST

DISCHARGE

OPENING

ROOF PITCH

H (MIN.) - MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE OPENING

* 3 foot minimum in snow regions

VERTICAL

WALL

IS X/ 12

Figure 10.15

H. Assemble and Install Storm Collar

CAUTION! Risk of Cuts, Abrasions or Flying Debris.

Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

• Connect both halves of the storm collar with two screws (see Figure 10.16).

• Wrap the storm collar around the exposed pipe section closest to the roof and align brackets. Insert a bolt (provided) through the brackets and tighten the nut to complete the storm collar assembly . Make sure the collar is tight against the pipe section.

• Slide the assembled storm collar down the pipe section until it rests on the roof ﬂ ashing (see Figure 10.17).

• Caulk around the top of the storm collar (see Figure 10.23).

Figure 10.14 Minimum Height From Roof To Lowest Discharge Opening

NOTICE: Failure to properly caulk the roof ﬂ ashing could cause water entry.

• Caulk the gap between the roof ﬂ ashing and the outside diameter of the pipe.

• Caulk the perimeter of the ﬂ ashing where it contacts the roof surface. See Figure 10.15.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 47

Figure 10.16 Assembling the Storm Collar

Figure 10.17 Assembling the Storm Collar Around the Pipe

Page 48

I. Install RF4-8

The RF4-8 may be used in place of the roof ﬂ ashing and storm collar (Sections 10.G. and 10.H.)

Pipe must be supported within 12 inches of the roofline using plumbers strapping or an SLP-FS when using the RF4-8 Flashing. Refer to Section 8.D. Secure Vent Sections.

SECURE WITH 4 SCREWS NO LONGER THAN 1 IN. (25 MM)

SLP-FS

Figure 10.18 Secure Pipe with SLP-FS

Figure 10.20 Apply Sealant

• Trim the rubber boot (using scissors or a utility knife), cutting along the marked measurement lines. See Figure

10.19. Use the 150 mm line for SLP, 210 mm for DVP.

• Lubricate pipe or ﬂ ue with water and slide the ﬂ ashing down. It may be necessary to trim the top shingles around the base of the rubber boot to ensure a good ﬁ t.

• Draw around ﬂ ashing, remove.

• Apply silicone sealant to roof inside the lines (Figure 10.20)

• Lubricate pipe or ﬂ ue with water and slide ﬂ ashing down. Seat ﬁ rmly in sealant. Nail roof ﬂ ashing to the roof.

• Apply silicone sealant on the top outside of the base plate on the sides and on top edge. See Figure 10.21. Install shingles, Apply sealant at the top edge of the rubber boot. See Figure 10.22.

• We recommend that you top coat with conventional acrylic house paint to improve the appearance of your galvanized base ﬂ ashing.

APPLY SEALANT

TOP & PARTIAL SIDES

Figure 10.21 Slide Flashing Down, Secure & Apply Sealant

SILICONE SEALANT (TOP OF BOOT)

SHINGLES TRIMMED

Figure 10.19 Trim Rubber Boot

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0848

FLASHING OVER SHINGLES

Figure 10.22 Installation Complete

SHINGLES OVER FLASHING

Page 49

Figure 10.23

J. Install Vertical Termination Cap

• Attach the vertical termination cap by sliding the inner collar of the cap into the inner ﬂ ue of the pipe section while placing the outer collar of the cap over the outer ﬂ ue of the pipe section.

• Secure the cap by driving three self-tapping screws (supplied) through the pilot holes in the outer collar of the cap into the outer ﬂ ue of the pipe (see Figure 10.23).

TERMINATION CAP

(1 of 3)

STORM COLLAR

SCREWS

CAULK

Figure 10.23

K. Install Decorative Wall Components (SLP

only)

A decorative wall thimble can be installed on wall through which the vent passes. The decorative wall thimble is used to cover the wall shield ﬁ restop.

• Slide the decorative wall thimble over the last section of horizontal pipe before connecting the termination cap to the pipe.

• Once the pipe section and the termination cap have been connected, slide the wall thimble up to the interior wall surface and attach with screws provided. See Figure

10.24.

L. Heat Shield Requirements for Horizontal

Termination

WARNING! Risk of Fire! To prevent overheating and ﬁ re, heat shields must extend through the entire wall thickness.

• DO NOT remove the heat shields attached to the wall shield ﬁ restop and the horizontal termination cap (shown in Figure 10.25).

• Heat shields must overlap 1-1/2 in. (38 mm) minimum.

There are two sections of the heat shield. One section is factory-attached to the wall shield ﬁ restop. The other section is factory-attached to the cap. See Figure 10.25.

If the wall thickness does not allow the required 1-1/2 in. (38 mm) heat shield overlap when installed, an extended heat shield must be used.

• If the wall thickness is less than 4 in./102 mm (DVP) or 4-3/8 in./ 111 mm (SLP), the heat shields on the cap and wall shield ﬁ restop must to be trimmed. A minimum 1-1/2 in. (38 mm) overlap MUST be maintained.

• Use an extended heat shield if the ﬁ nished wall thickness is greater than 7-1/4 in. (184 mm).

• The extended heat shield may need to be cut to length maintaining sufﬁ cient length for a 1-1/2 in. (38 mm) overlap between heat shields.

• Attach the extended heat shield to either of the existing heat shields using the screws supplied with the extended heat shield. Refer to vent components diagrams in the back of this manual.

• Rest the small leg on the extended heat shield on top of the pipe section to properly space it from the pipe section.

Important Notice: Heat shields may not be ﬁ eld constructed.

Figure 10.24 Wall Thimble

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 49

Page 50

M. Install Horizontal Termination Cap (DVP

and SLP Pipe)

WARNING! Risk of Fire! The telescoping ﬂ ue section of the termination cap MUST be used when connecting vent.

• 1-1/2 (38 mm) minimum overlap of ﬂ ue telescoping section is required.

Failure to maintain overlap may cause overheating and ﬁ re.

• Vent termination must not be recessed in the wall. Siding may be brought to the edge of the cap base.

• Flash and seal as appropriate for siding material at outside edges of cap.

• When installing a horizontal termination cap, follow the cap location guidelines as prescribed by current ANSI Z223.1 and CAN/CGA-B149 installation codes and refer to Section 6 of this manual.

CAUTION! Risk of Burns! Local codes may require installation of a cap shield to prevent anything or anyone from touching the hot cap.

NOTICE: For certain exposures which require superior resistance to wind-driven rain penetration, a ﬂ ashing kit and HRC caps are available. When penetrating a brick wall, a brick extension kit is available for framing the brick.

Note: When using termination caps with factory-supplied heat shield attached, no additional wall shield ﬁ restop is required on the exterior side of a combustible wall.

HEAT SHIELD OR

EXTENDED

WALL SHIELD

FIRESTOP

INNER VENT

OUTER VENT

VENT DEPTH FROM BACK OF APPLIANCE TO

OUTSIDE SURFACE OF EXTERIOR WALL

(SEE CHART BELOW)

Figure 10.25 Venting through the wall

HEAT SHIELD

SLIP SECTION

CAN BE EXTENDED

INTERIOR

Cap Speciﬁ cation Chart

(depth without using additional pipe sections)

DVP-TRAPK1

Top Vent

Depth

2-7/8 in to

36 inch

Multisided

Series

DVP-TRAP1 can adjust 1-1/2 in. (3-1/8 to 4-5/8 in.) DVP-TRAP2 can adjust 4 in. (5-3/8 to 9-3/8) DVP-HPC1 can adjust 2-1/8 in. (4-1/4 to 6-3/8) DVP-HPC2 can adjust 4-1/8 in. (6-3/8 to 10-1/2)

4-3/4 in

DVP-HPC1

Top Vent

Depth

2-7/8 in.

to 5 in.

DVP-TRAP1

Rear Vent

Depth

3-1/8 in.

to 5 in.

DVP-HPC1

Rear Vent

Depth

3-1/8 in. 5-1/4 in.

DVP-TRAPK2

Top Vent

Depth

5-1/4 in. to

9-1/4 in.

DVP-HPC2

Top Vent

Depth

5 in. to

9-1/8 in.

HEAT SHIELD

1-1/2 IN. (38 MM) MIN.

OVERLAP

SHEATHING

EXTERIOR

DVP-TRAP2

Rear Vent

Depth

5-1/2 in. to

9-1/2 in.

DVP-HPC2

Rear Vent

Depth

5-1/4 in. to

9-1/2 in.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0850

Page 51

Gas Information

A. Fuel Conversion

• Make sure the appliance is compatible with available gas types.

• Conversions must be made by a qualified service technician using Hearth & Home T echnologies speciﬁ ed and approved parts.

B. Gas Pressure

• Optimum appliance performance requires proper input pressures.

• Gas line sizing requirements will be determined in ANSI



Z223.1 National Fuel Gas Code in the USA and CAN/ CGA B149 in Canada.

• Pressure requirements are:

Gas Pressure Natural Gas Propane

Minimum inlet pressure 5.0 in. w.c. 11.0 in. w.c. Maximum inlet pressure 14.0 in. w.c. 14.0 in. w.c. Manifold pressure 3.5 in. w.c. 10.0 in. w.c.

WARNING! Risk of Fire/Explosion! High pressure will damage valve. Low pressure may cause explosion.

• Verify inlet pressures. Verify minimum pressures when other household gas appliances are operating.

• Install regulator upstream of valve if line pressure is greater than 1/2 psig.

WARNING

Fire Risk. Explosion Hazard. High pressure will damage valve.

• Disconnect gas supply piping BEFORE pressure testing gas line at test pressures above 1/2 psig.

• Close the manual shutoff valve BEFORE pressure testing gas line at test pressures equal to or less than 1/2 psig.

Note: Have the gas supply line installed in accordance with local codes, if any. If not, follow ANSI 223.1. Installation should be done by a qualiﬁ ed installer approved and/or licensed as required by the locality. (In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas ﬁ tter).

Note: A listed (and Commonwealth of Massachusetts approved) 1/2 in. (13 mm) T-handle manual shut-off valve and ﬂ exible gas connector are connected to the 1/2 inch (13 mm) control valve inlet.

• If substituting for these components, please consult local codes for compliance.

C. Gas Connection

• Refer to Reference Section 16 for location of gas line access in appliance.

• Gas line may be run through knockout(s) provided.

• The gap between supply piping and gas ac cess hole may be caulked with high temperature caulk or stuf fe d with non-combustible, unfaced insulation to prev ent cold air inﬁ ltration.

• Ensure that gas line does not come in contact with outer wrap of the appliance. Follow local codes.

• Pipe incoming gas line into valve compartment.

• Connect incoming gas line to the 1/2 in. (13 mm) connection on manual shutoff valve.

WARNING! Risk of Fire or Explosion! Support control when attaching pipe to prevent bending gas line.

• A small amount of air will be in the gas supply lines.

WARNING! Risk of Fire or Explosion! Gas build-up dur ing line purge could ignite.

• Purge should be performed by qualified service

technician.

• Ensure adequate ventilation.

• Ensure there are no ignition sources such as sparks

or open ﬂ ames.

Light the appliance. It will take a short time for air to purge from lines. When purging is complete the appliance will light and operate normally.

WARNING! Risk of Fire, Explosion or Asphyxiation!

Check all ﬁ ttings and connections with a non-corrosive commercially available leak-check solution. DO NOT use open ﬂ ame. Fittings and connections could have loos- ened during shipping and handling.

WARNING! Risk of Fire! DO NOT change valve settings. This valve has been preset at the factory.

D. High Altitude Installations

NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.

When installing above 2000 feet elevation:

• In the USA: Reduce burner oriﬁ ce 4% for each 1000 feet above 2000 feet.

• In the CANADA: Reduce burner oriﬁ ce 10% for elevations between 2000 feet and 4500 feet. Above 4500 feet, consult local gas utility.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 51

Page 52

Electrical Information

A. Wiring Requirements

NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code

ANSI/NFPA 70-latest edition or the Canadian Electric Code CSA C22.1.

• Wire the appliance junction box to 110-120 VAC. This is required for use of optional accessories (standing pilot ignition) or proper operation of the appliance (Intelliﬁ re ignition).

• A 110-120 VAC circuit for this product must be protected

with ground-fault circuit-interrupter protection, in compliance with the applicable electrical codes, when it is

installed in locations such as in bathrooms or near sinks.

• Low voltage and 110 VAC voltage cannot be shared within the same wall box.

WARNING! Risk of Shock or Explosion! DO NOT wire 1 10V to the valve or to the appliance wall switch. Incorrect wiring will damage controls.

C. Optional Accessories Requirements

• This appliance may be used with a wall switch, wall mounted thermostat and/or a remote control.

Wiring for optional Hearth & Home T echnologies approved accessories should be done now to avoid reconstruction. Follow instructions that come with those accessories.

D. Electrical Service and Repair

WARNING! Risk of Shock! Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

WARNING! Risk of Shock! Replace damaged wire with type 105° C rated wire. Wire must have high temperature insulation.

B. Intelliﬁ re Ignition System Wiring

• Wire the appliance junction box to 110 VAC for proper operation of the appliance.

WARNING! Risk of Shock or Explosion! DO NOT wire IPI controlled appliance junction box to a switched circuit. Incorrect wiring will override IPI safety lockout.

• Refer to Figure 12.2, Intelliﬁ re Pilot Ignition (IPI) Wiring Diagram.

• This appliance is equipped with an Intelliﬁ re control valve which operates on a 3 volt system.

• Plug the 3-volt AC transformer into the appliance junction box to supply power to the unit OR install two D cell batteries (not included) into the battery pack before use.

NOTICE: Batteries should not be placed in the battery pack while using the transformer. Remove batteries before using the transformer, and unplug the transformer before installing the batteries. Battery polarity must be correct or module damage will occur.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0852

Page 53

IGNITION

MODULE 3 VAC

INTERMITTENT

PILOT IGNITOR

TRANSFORMER

PLUG IN

3 VAC

RED

THERMOSTAT

WIRE ASSEMBLY

BLACK

BATTERY PACK

HOT

NEUTRAL

Figure 12.1 Intelliﬁ re Ignition Wiring Diagram with Wall Switch or Thermostat

NOTE: 1. Ignition module, valve, pilot, and

wall switch operate on 3 volts. 120 VAC is required at junction box unless equipped with battery back-up.

WIRES (TO BROWN)

ORANGE

WHITE

GROUND TO

FIREPLACE

CHASSIS

IGNITION

MODULE 3 VAC

ORANGE

VALVE

GREEN

INTERMITTENT PILOT IGNITOR

TRANSFORMER

HOT

BATTERY PACK

PLUG IN

NEUTRAL

PLUG IN

REMOTE

Figure 12.2 Intelliﬁ re Ignition Wiring Diagram with Remote Receiver

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 53

3 VAC

RED

BLACK

WIRES (TO BROWN)

ORANGE

WHITE

GROUND TO

FIREPLACE

CHASSIS

ORANGE

VALVE

GREEN

Page 54

E. Junction Box Installation

The junction box must be wired from the INSIDE of the appliance:

• Determine which side of the appliance the junction box is located on.

• Pull the electrical wires from outside the appliance through the knockout making sure to use a Romex connector to fasten the electrical wires to the unit.

• Pull enough wire into the valve compartment to easily reach the junction box location.

• Remove the screw attaching the junction box to the junction box bracket and set it aside.

• Route the wire through the knockout in the junction box bracket.

• Wire the junction box and reattach it to the bracket by inserting the tab in the slot and attaching with screw previously removed. Ensure that a Romex connector is used to attach the electrical wires to the junction box.

ROMEX CONNECTORS

Figure 12.4 Junction Box Detail

NOTICE: DO NOT wire 110 VAC to wall switch.

F. Wall Switch Installation for Fan (Optional)

If the box is being wired to a wall mounted switch for use with a fan (See Figure 12.5):

• The power supply for the appliance must be brought into a switch box.

• The power can then be supplied from the switch box to the appliance using a minimum of 14-3 with ground wire.

• At the switch box connect the black (hot) wire and red (switch leg) wire to the wall switch as shown.

• At the appliance connect the black (hot), white (neutral) and green (ground) wires to the junction box as shown.

• Add a 1/4 in. insulated female connector to the red (switch leg) wire, route it through the knockout in the face of the junction box, and connect to the top fan switch connector (1/4 in. male) as shown.

MINIMUM 14-3 AWG WITH GROUND

JUNCTION BOX

RED

Figure 12.5 Junction Box Wired to Wall Switch

RED

WHITE

BLACK

RED

BLACK

GREEN

WHITE

GREEN

KNOCKOUT

SWITCH BOX

BLACK WHITE

GREEN

SWITCH

POWER SUPPLY

WIRES

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0854

Page 55

Finishing

A. Splatter Guard

The splatter guard is a piece of corrugated material used to protect the appliance during the installation process before ﬁ nishing work on the whole hearth is complete.

Splatter guards must be removed before appliance is ﬁ red.

WARNING

Risk of Fire

• Splatter guard must be removed before lighting appliance.

• Before splatter guard is installed:

Close ball valve to prevent accidental lighting.

Step 1. Turn off gas to valve. Red gas shutoff knob is located on ball valve. Disconnect the 3 volt transformer from the junction box. See Figure 13.1.

Figure 13.1 Preparation to Install Splatter Guard

To install the Splatter Guard:

Step 2. Crease ﬂ ap on top side of splatter guard using the scored line as the guide. See Figure 13.2.

Figure 13.3 Folding of Right and Left Sides of Splatter Guard

Step 4. Center the splatter guard in front of the unit as shown in Figure 13.3. Place the splatter guard in the unit by guiding the top ﬂ ap into proper position and then con- tinuing to guide the tabs on the side ﬂ aps into the top slot on the left and right sides of the appliance. The top slot is indicated in Figure 13.5 Take care not to bend or break off the tabs.

Figure 13.4 Installation of Splatter Guard

Figure 13.2 Folding Top Flap

Step 3. Crease ﬂ aps on left and right sides of splatter guard using the scored line as the guide. See Figure 13.2.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 55

TOP SLOT

Figure 13.5 Top slot

Page 56

Step 5. Fold bottom ﬂ ap along score line as indicated in Figure 13.6 and tuck into valve access area of appliance. Splatter guard should ﬁ t securely on front of unit.

Figure 13.6 Folding Bottom Flap

Figure 13.9 Securing Tabs Inside Front of Splatter Guard

Once plumbing and wiring are complete on the ﬁ replace, the lower access panel may be closed until the time that the splatter guard must be removed for ﬁ ring the appliance.

Figure 13.7 Prepare to Open Lower Access Panel

Step 6. To open lower access panel of splatter guard, place one hand above score line and place two ﬁ ngers from other hand in the round holes on the front of the splatter guard. See Figure 13.7. Pull out and fold up the panel as shown in Figure 13.8. Disengage the tabs on left and right bottom of splatter guard and ﬁ t them into the square holes. The tabs are now inside the front of the splatter guard; carefully bend them down. See Figure

13.8.

Figure 13.10 Splatter Guard with Lower Access Panel Open

To Close the Lower Access Panel:

Carefully disengage the tabs from the square holes and bend the access panel to its original position. Bend the center bottom ﬂ ap and insert it into the bottom of the ap- pliance.

Figure 13.8 Opening Lower Access Panel

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0856

Figure 13.11 Splatter Guard with Lower Access Panel Closed

To Remove the Splatter Guard:

Carefully grab splatter guard on or near the vertical center on the left and right sides. Pull outward gently, but ﬁ rmly, taking care not to tear or remove the inserted tabs.

Page 57

B. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clearances as speciﬁ ed. Framing closer than the minimums list- ed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc.) Failure to comply could cause ﬁ re.

See-Through Mantel Projection

TO CEILING

Note: All measurements in inches.

2-1/2

See-Through Mantel Projection

TO CEILING

Note: All measurements in inches.

Figure 13.14 Minimum Vertical and Maximum Horizontal Dimensions of Non-Combustibles

MAX.

MEASUREMENTS FROM

TOP EDGE OF THE OPENING

MIN.

MEASUREMENTS FROM

TOP EDGE OF THE OPENING

Figure 13.12 Minimum Vertical and Maximum Horizontal Dimensions of Combustibles

PIER/LCOR/RCOR Mantel Projection

TO CEILING

Note: All measurements in inches.

MEASUREMENTS FROM

TOP EDGE OF THE OPENING

PIER/LCOR/RCOR Mantel Projection

TO CEILING

MAX.

Note: All measurements in inches.

MEASUREMENTS FROM

TOP EDGE OF THE OPENING

Figure 13.15 Minimum Vertical and Maximum Horizontal Dimensions of Non-Combustibles

MIN.

Figure 13.13 Minimum Vertical and Maximum Horizontal Dimensions of Combustibles

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 57

Page 58

TOP VIEW

FIREPLACE

OPENING

2-3/4

in. Min.

1 in.

Min.

Unlimited

Max.

3-1/4 in. Min.

Note: Clearance from opening to perpendicular wall.

1/2 in.

Figure 13.16 Combustible Mantel Leg or Wall Projections



(Acceptable on both sides of opening)

C. Facing Material

• Metal front faces may be covered with non-combustible materials only.

• Facing and/or ﬁ nishing materials must not interfere with air ﬂ ow through louvers, operation of louvers or doors, or access for service.

• Facing and/or ﬁ nishing materials must never overhang into the glass opening.

• Observe all clearances when applying combustible materials.

• Seal joints between the ﬁ nished wall and appliance top and sides using a 300 °F minimum sealant. Refer to Figure 13.17.

WARNING! Risk of Fire! DO NOT apply combustible materials beyond the minimum clearances. Comply with all minimum clearances to combustibles as speciﬁ ed in this manual. Overlapping materials could ignite and will interfere with proper operation of doors and louvers.

D. Finishing Material

Only doors certiﬁ ed for use with this appliance model may be used. Contact your dealer for a list of doors that may be used. Once you have determined what kind of door and ﬁ nishing material is going to be used on the ﬁ replace, you may use the table below which shows the door models and the ﬁ nishing material thickness allowed. For an inside ﬁ t there is an available template to assist with siz- ing the ﬁ nishing material.

ST-36TRB-IPI

DOOR FIT

Aero Inside Any 13.18 Folio Inside Any 13.18

Arcadia

Halston

Chateau

Valencia

Galleria

Overlap 1 inch 13.19

Inside Any 13.20

Overlap 1 inch 13.19

Inside 1 inch - 2 inch 13.21

Overlap 1 inch 13.19

Inside Any 13.20

Overlap 1 inch 13.19

Inside Any 13.20

Overlap 1 inch 13.19

Inside 1 inch - 2 inch 13.21

PIER-36TRB-IPI

DOOR FIT

Aero Inside Any 13.22

Chateau Inside Any 13.22

Arcadia Inside Any 13.22

FINISH MATERIAL

MAXIMUM

THICKNESS

FINISH MATERIAL

MAXIMUM

THICKNESS

SEE FIGURE



Finish wall material may be combustible - Top and Sides

0 in.

High Temperature Sealant (300° F/149° C min.)

Top and Side Seal Joint

Figure 13.17 Noncombustible Facing Diagram

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0858

0 in.

FINISHING MATERIAL 4 IN. MAXIMUM THICKNESS

DOOR

Stop ﬁ nishing material ﬂ ush with opening.

Figure 13.18 Folio Door and Aero

FRONT FACE OF FIREPLACE

DOOR

Finishing materials 1 inch maximum thick.

Stop ﬁ nishing material ﬂ ush with opening.

Figure 13.19 Overlap Fit Door

FINISHING MATERIAL 4 IN. MAXIMUM THICKNESS

1 in. MAX

FINISHING MATERIAL

(TOP EDGE)

Page 59

FINISHING MATERIAL

DOOR

37-1/4 in.

(Includes 1/8 in. opening each side of door)

37 in.

(Outside door width)

37-1/4 in.

(Includes 1/8 in. opening each side of door)

Finishing materials over 1 inch thick.

Figure 13.20 Inside ﬁ t door

37 in.

(Outside door width)

33-3/4 in.

(Inside door height)

34 in.

33-5/8 in.

37-1/4 in.

Figure 13.22 Pier Door Finishing



FINISHING

MATERIAL

*IF FINISHING MATERIAL IS THICKER THAN

2 IN., DOORS WILL ONLY OPEN

AS FAR AS PICTURED

DOORS

33-3/4 IN.

37-1/4 IN.

Finishing material between 1 and 2 inches thick.

Figure 13.21 Operable hinge door

FINISHING MATERIAL

34 IN.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 59

Page 60

E. Elevated Hearth Systems

Use the table below to identify the hearth system that will be used. The table will also help identify effects on the various dimensions. Some hearth systems will elevate the appliance off the ﬂ oor at a given dimension. For example, if appliance will be used with a Kenwood Cabinet with Base, the appliance will be elevated 9-1/4 inches. The 9-1/4 inch elevation will also have to be added to the following: Extension Wall Hole referenced in Figure 8.2 (Exterior Wall Hole) and Rough



Opening Height (header height) referenced in Figure 5.2. Note: Finished ﬂ oor thickness should also be considered when determining installation dimensions.

MODEL DESCRIPTION PART #

KENWOOD CABINET KDC48DBP 0 32-7/8 in. KENWOOD CABINET W/ BASE KDC48DBP W/ HTKDC48DBP 9-1/4 in. 32-7/8 in. KENWOOD CORNER CABINET KDA48SBP 0 32-7/8 in. KENWOOD CORNER CABINET W/ BASE KDA48SBP W/ HTKDA48SBP 9-1/4 in. 32-7/8 in. KENWOOD MANTEL AFKDMPB 0 (See Note 3) 27-3/8 in. KENWOOD MANTEL W/ BASE AFKDMPB W/ HTKDMPB 9-1/4 in. 29-3/8 in. LAURENT SURROUND LAURENT-36 1-1/2 in. N/A CAMDEN SURROUND CAM36PG 0 N/A CAMDEN SURROUND W/HEARTH CAM36PGH 1-3/4 in. N/A CAMDEN SURROUND W/MANTEL CAMM36PG 0 N/A

ST-36TRB-IPI

CAMDEN SURROUND W/MANTEL & HEARTH

ESSEX SURROUND ESSEX36PG 0 N/A ESSEX SURROUND W/HEARTH ESSEX36PGH 1-3/4 in. N/A ESSEX SURROUND W/MANTEL ESSEXM36PG 0 N/A ESSEX SURROUND W/MANTEL &

HEARTH MONROE SURROUND MON36PG 0 N/A MONROE SURROUND W/HEARTH MON36PGH 1-3/4 in. N/A MONROE SURROUND W/MANTEL MONM36PG 0 N/A MONROE SURROUND W/MANTEL &

HEARTH

CAMM36PGH 1-3/4 in. N/A

ESSEXM36PGH 1-3/4 in. N/A

MONM36PGH 1-3/4 in. N/A

ELEVATED APPLIANCE

DIMENSION

See Note 1

MARBLE LEG CUT

LENGTH

See Note 2



Note 1. Add dimensions to Exterior Wall Hole (Figure 8.2) and Rough Opening Height (Figure 5.2). Note 2. Verify Marble Cut Lengths on site prior to cutting. Note 3. Dimensions assume use of a 3/4 in. Hearth Pad.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0860

Page 61

Appliance Setup

A. Remove Fixed Glass Assembly

See Section 14G.

B. Remove the Shipping Materials

Remove shipping materials from inside or underneath the ﬁ rebox.

C. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the ﬁ rebox or underneath in the control cavity.

D. Accessories

Install approved accessories per instructions included with accessories. Contact your dealer for a list of approved accessories.

WARNING! Risk of Fire and Electric Shock! Use ONLY Hearth & Home Technologies-approved optional accessories with this appliance. Using non-listed accessories could result in a safety hazard and will void the warranty.

E. Lava Rock and Glowing Ember Placement

WARNING! Risk of Explosion! Follow ember placement instructions in manual. DO NOT place embers directly over burner ports. Replace ember material annually . Improperly placed embers interfere with proper burner operation.

Placing the Ember Material

Ember material is shipped with this gas appliance. T o place the ember material:

• Embers CANNOT be placed directly over ports. Care should be taken not to cover the lighting trail of ports (from back to front).

• When placing Glowing Embers® onto the burner care should be taken so that the ports are not covered. Place the dime-size ember pieces just in front of the port trail, but not on or in between the ports (see Figure 14.1). Failure to follow this procedure will likely cause lighting and sooting problems.

DO NOT PLACE EMBERS IN THE CIRCLED AREAS

PILOT LOCATED HERE

Figure 14.1 Placement of Embers

• Place Glowing Embers on top of the log attachment tabs to conceal their location. Ensure that the Glowing Embers do not obstruct the port trail.

• Place Lava Rock on areas of base pan away from the burner. Use this material to give the appliance a realistic ash bed.

• Save the remaining ember materials for use during appliance servicing. The embers provided should be enough for 3 to 5 applications.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 61

Page 62

F. Install the Log Assembly

Figure 2. Factory Installed Logs

FFigure 1. Log Assembly Location

PILOT

Figure 4. Placement of Log #1

FFigure 3. Placement of Log #1

NOTCH

HUMP

ST-36TVB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI

CAUTION: DO NOT reposition logs that have been factory installed! Follow these instructions to position

the logs that were packaged separately.

Log Set Assembly: LOGS-2128

Models: ST-36TRB-IPI, PIER-36TRB-IPI

PILOT

igure 1. Log Assembly Location

STEP 1. CAUTION! Logs are fragile! Carefully remove the logs and cardboard tray from the inside of the ﬁ replace.

See Figure 1. Remove the microfoam and inspect the logs for damage. Inspect the four factory installed logs for damage. Locate the pilot in order to verify your position in relation to the appliance. See Figure 2.

NOTCH

Figure 2. Factory Installed Logs

HUMP

igure 3. Placement of Log #1

STEP 2. Log #1 (SRV2128-704): Mate the notch on the end of log # 1 with the hump on top of log A. Set the other

end of Log #1 onto the smooth area on top of Log C.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0862

Figure 4. Placement of Log #1

2128-935

Page 63

FFigure 5. Placement of Log #2

FFigure 7. Placement of Log #3

INDENTATIONS

Figure 6. Placement of Log #2

GRATE TINES

Figure 8. Placement of Log #3

GRATE TINES

PILOT

igure 5. Placement of Log #2

STEP 3. Log #2 (SRV2128-705): The Y-shaped end of log #2 should rest on log B and log C. The other end should

come in contact with the second grate tine from the left. Mate the bottom of log # 2 with the notches on top of log B and the smooth area on top of the end of log C.

INDENTATIONS

Figure 6. Placement of Log #2

GRATE TINES

igure 7. Placement of Log #3

STEP 4. Log #3 (SRV2128-707): The bottom end of log #3 should come in contact with the far left grate tine. Mate

the bottom of log # 3 with the indentations on Log D and the top of Log #2.

Figure 8. Placement of Log #3

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 63

Page 64

G. Fixed Glass Assembly

WARNING! Risk of Asphyxiation! Handle ﬁ xed glass assembly with care. Inspect the gasket to ensure it is undamaged and inspect the glass for cracks, chips or scratches.

• DO NOT strike, slam or scratch glass.

• DO NOT operate ﬁ replace with glass removed, cracked, broken or scratched.

• Replace as a complete assembly.

Removing Fixed Glass Assembly

• Pull the four glass latches out of the grooves on the glass frame top and bottom.

• Remove the glass door from the appliance.

• Multiple sides may be able to be removed based upon model.

Replacing Fixed Glass Assembly

• Replace the glass door on the appliance.

• Pull out the four glass latches and place in the grooves on the glass frame top and bottom.

• Make sure all sides are replaced properly.

H. Install Trim Kits and Surrounds

• Install optional trim kits and/or surrounds using the instructions included with the accessory.

• Use non-combustible materials to cover the gap between the sheet rock and the appliance (if desired).

I. Air Shutter Setting

This appliance has an adjustable air shutter (which controls the primary air) factory set for the minimum vertical vent run (see Figure 12.15). If your installation has more than the minimum required vertical vent length, adjustment of the air shutter may be necessary to obtain optimal ﬂ ame appearance. This should be adjusted by a

qualiﬁ ed installer at the time of installation.

By pushing the air shutter handle towards the pilot, you will be closing the air shutter. To adjust loosen the wing nut. Care should be taken when adjusting the air shutter so as not to cause the appliance to soot. If sooting occurs the air shutter will need to be opened by pushing the handle away from the pilot. When ﬁ nished tighten wing nut.

NOTICE: If sooting occurs, provide more air by opening the air shutter.

LATCHES

OTH BOTTOM

AND TOP)

GLASS

ASSEMBLY

Figure 14.3 Fixed Glass Assembly

AIR SHUTTER

OPEN

CLOSED

Figure 14.4 Air Shutter

Air Shutter Settings

NG LP

Burner 1/8 in. Fully open

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0864

Page 65

Troubleshooting

With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualiﬁ ed technician in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualiﬁ ed technician. Contact your dealer to arrange a service call by a qualiﬁ ed technician.

A. Intelliﬁ re Ignition System

Symptom Possible Cause Corrective Action

1. Pilot won’t light. The ignitor/module makes noise, but no spark.

2. Pilot won’t light, there is no noise or spark.

a. Incorrect wiring. Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor

are connected to correct terminals on module and pilot assembly.

b. Loose connections or electrical

shorts in the wiring.

c. Ignitor gap is too large. Verify gap of igniter to right side of pilot hood. The gap should be

d. Module. Turn ON/OFF rocker switch or wall switch to OFF position. Remove

a. No power or transformer installed

incorrectly.

b. A shorted or loose connection in wir-

ing conﬁ guration or wiring harness.

Verify no loose connections or electrical shorts in wiring from module to pilot assembly. Verify connections underneath pilot assembly are tight; also verify connections are not grounding out to metal chassis, pilot burner, pilot enclosure, mesh screen if present, or any other metal object.

approximately .17 in. or 1/8 in. (3 mm).

ignitor wire “I” from module. Place a grounded wire about 3/16 in. (5 mm) away from “I” terminal on module. Place ON/OFF rocker switch or wall switch in ON position. If there is no spark at “I” terminal module must be replaced. If there is a spark at “I” terminal, module is ﬁ ne. Inspect pilot assembly for shorted sparker wire or cracked insulator around electrode. Replace pilot if necessary .

Verify that transformer is installed and plugged into module. Check voltage of transformer under load at spade connection on module with ON/OFF switch in ON position. Acceptable readings of a good transformer are between 3.2 and 2.8 volts AC.

Remove and reinstall the wiring harness that plugs into module. Verify there is a tight ﬁ t. Verify pilot assembly wiring to module. Re- move and verify continuity of each wire in wiring harness. Replace any damaged components.

3. Pilot sparks, but Pilot will not light.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 65

c. Improper wall switch wiring. Verify that 110/VAC power is “ON” to junction box. d. Module not grounded. Verify black ground wire from module wire harness is grounded to

metal chassis of appliance.

e. Module. Turn ON/OFF rocker switch or wall switch to OFF position. Re-

move ignitor wire “I” from module. Place ON/OFF rocker switch or wall switch in ON position. If there is no spark at “I” terminal module must be replaced. If there is a spark at “I” terminal, module is ﬁ ne. Inspect pilot assembly for shorted sparker wire or cracked insulator around electrode.

a. Gas supply. Verify that incoming gas line ball valve is “open”. Verify that inlet

pressure reading is within acceptable limits, inlet pressure must

not exceed 14 in. W.C. b. Ignitor gap is incorrect. Verify that spark gap from ignitor to pilot hood is .17 in. or 1/8 in (3 mm). c. Module is not grounded. Verify module is securely grounded to metal chassis of appliance. d. Module voltage output / Valve/Pilot

solenoid ohms readings.

Verify battery voltage is at least 2.7 volts. Replace batteries if volt-

age is below 2.7.

Page 66

Intelliﬁ re Ignition System - (continued)

Symptom Possible Cause Corrective Action

4. Pilot lights but continues to spark, and main burner will not ignite. (If the pilot continues to spark after the pilot ﬂ ame has been lit, ﬂ ame rectiﬁ cation has not occurred.)

a. A shorted or loose connection in ﬂ ame

sensing rod.

b. Poor ﬂ ame rectiﬁ cation or contaminated

ﬂ ame sensing rod.

c. Module is not grounded. Verify module is securely grounded to metal chassis of

d. Damaged pilot assembly or contami-

nated ﬂ ame sensing rod.

e. Module. Turn ON/OFF rocker switch or wall switch to OFF position.

Verify all connections to wiring diagram in manual. Verify connections underneath pilot assembly are tight. Verify connections are not grounding out to metal chassis, pilot burner, pilot enclosure or screen if present, or any other metal object.

With ﬁ xed glass assembly in place, verify that ﬂ ame is en- gulﬁ ng ﬂ ame sensing rod on left side of pilot hood. Flame sensing rod rect pilot oriﬁ ce is installed and gas inlet is set to pressure speciﬁ cations. Clean ﬂ ame sensing rod with emery cloth to remove any contaminants that may have accumulated on ﬂ ame sensing rod.

appliance. Verify that wire harness is ﬁ rmly connected to the module.

Verify that ceramic insulator around the ﬂ ame sensing rod is not cracked, damaged, or loose. Verify connection from ﬂ ame sensing rod to white sensor wire. Clean ﬂ ame sensing rod with emery cloth to remove any contaminants that may have accumulated on ﬂ ame sensing rod. Verify continuity with a multimeter with ohms set at lowest range. Replace pilot if any damage is detected.

Remove ignitor wire “I” from module. Place ON/OFF rocker switch or wall switch in ON position. If there is no spark at “I” terminal module must be replaced. If there is a spark at “I” terminal, module is ﬁ ne.

should glow shortly after ignition. Verify cor-

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0866

Page 67

Reference Materials

A. Appliance Dimension Diagram

Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5.

Ø K

ELECTRICAL

ACCESS

Ø K



LEFT VIEW

FRONT VIEW RIGHT VIEW

Location Inches Millimeters

A 36 914 B 42-1/2 1080 C 24-1/2 622 D 33-1/2 851 E1 25

F 2-1/8 54 G 4-1/8 105 H 4-1/4 108

Location Inches Millimeters

I 1-1/2 38 J 27 686 K 8 203 L 12 305

M 9-1/2 241 N 38 965 O 34-5/8 880

P 24 610

GAS LINE

ACCESS

Figure 16.1 See-Through Dimensions

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 67

Page 68

Ø K

ELECTRICAL

ACCESS

Ø K

GAS LINE

ACCESS

LEFT VIEW

FRONT VIEW RIGHT VIEW

Location Inches Millimeters

Figure 16.2 Pier Dimensions

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0868

A 36 914 B 40-1/2 1029 C 24-1/2 622 D 33-1/2 851 E1 25 F 2-1/8 54 G 4-1/8 105 H 4-1/4 108

Location Inches Millimeters

I 1-1/2 38 J 27 686

K 8 203

L 12 305 M 9-1/2 241 N 38 965 O 34-5/8 880

P 24 610

Page 69

Ø K

ELECTRICAL

ACCESS

Ø K

LEFT VIEW

FRONT VIEW RIGHT VIEW

Location Inches Millimeters

A 36 914

B 40-1/2 1029 C 24-1/2 622 D 33-1/2 851

E1 25

F 2-1/8 54 G 4-1/8 105 H 4-1/4 108

Location Inches Millimeters

I 1-1/2 38

J 27 686

K 8 203

L 12 305 M 9-1/2 241 N 24-1/2 622 O 38 965 P 34-5/8 880

GAS LINE

ACCESS

Figure 16.3 LCOR, RCOR Dimensions

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 69

Page 70

B. Vent Components Diagrams

DVP Pipe (see chart)

10 in.

(254 mm)

24 in.

(610 mm)

Effective

Height/Length

10 in.

(254 mm)

Pipe

DVP4 4 102 DVP6 6 152 DVP12 12 305 DVP24 24 610 DVP36 36 914 DVP48 48 1219 DVP6A 3 to 6 76 to 152 DVP12A 3 to 12 76 to 305 DVP12MI 3 to 12 76 to 305 DVP24MI 3 to 24 76 to 610

Effective Length

Inches Millimeters

10 in.

(254 mm)

1 in.

(25 mm)

10-1/2 in. (267 mm)

4-7/8 in.

( 276 mm)

9-1/4 in.

(235 mm)

13-1/4 in. (337 mm)

10-7/8 in. (276 mm)

DVP45 (45 Elbow)

11-3/8 in. (289 mm)

7-3/8 in.

(187 mm)

1-1/4 in. (32 mm)

1/2 in.

TYP

(13 mm)

DVP-AS (Attic Shield)

10 in.

(254 mm)

5 in.

(127 mm)

DVP-HVS (Vent Support)

Figure 16.4 DVP vent components

DVP-FS (Ceiling Firestop)

1- 1/2 in.

(38 mm)

12 in.

(305 mm)

14 in.

(356 mm)

DVP90ST (90° Elbow)

12 in.

(305 mm)

6 in.

(152 mm)

DVP-WS (Wall Shield Firestop)

1 in. (25 mm)

8 in.

(203 mm)

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0870

Page 71

B. Vent Components Diagrams (continued)

Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the

existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B will be required.

15-1/8 in. (384 mm)

12 in.

(305 mm)

DVP-TRAP

Horizontal Termination Cap

8 in.

(203 mm)

Max

Effective

Length

Heat

Shield

Term Cap

Trap1

Trap2

Minimum

Effective Length

3-1/8 in. 4-5/8 in.

79 mm 117 mm 5-3/8 in. 9-3/8 in. 137 mm 238 mm

Effective Length

Maximum

DVP-TRAP1

DVP-TRAPK1

DVP-HPC1

DVP-TRAP2

DVP-TRAPK2

DVP-HPC2

Figure 16.5 DVP vent components

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 71

Page 72

B. Vent Components Diagrams (continued)

13-1/4 in.

(367 mm)

31 in.

(787 mm)

24-5/8 in.

(625 mm)

24-5/8 in.

(625 mm)

13-3/4 in. (349 mm)

RF6M

Roof Flashing Multi-pak

13-3/4 in. (349 mm)

BEK

Trap Cap Brick Extension

27-1/2 in.

(127 mm)

5 in.

(127 mm)

13-7/8 in. (352 mm)

13-1/4 in.

(367 mm)

RF12M

Roof Flashing Multi-pak

11-7/8 in.

(302 mm)

DVP-BEK2

DVP-HPC Cap Brick Extension

5 in.

(127 mm)

DVP-TRAPFL

Flashing

26 in.

660 mm

DVP-HSM-B Extended Heat Shield

Figure 16.6 DVP vent components

7-1/8 in.

(181 mm)

11-5/8 in.

(295 mm)

5-3/4 in.

(146 mm)

14 in.

(356 mm)

12-1/8 in.

(308 mm)

COOL-ADD

Cap Shield

13-7/8 in. (352 mm)

DRC-RADIUS

9-1/2 in.

(241 mm)

Cap Shield

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0872

Page 73

B. Vent Components Diagrams (continued)

7-3/8 in.

(187 mm)

1-1/2 in. (38 mm)

3-7/8 in. (98 mm)

14 in.

(356 mm)

12 in.

(305 mm)

DVP-TB1

BasementVent Cap

PVK-80

(For use with IPI and DSI appliances only.)

17-3/4 in.

(451 mm)

7-1/4 in.

(184 mm)

5-1/4 in.

(133 mm)

10-1/2 in.

(267 mm) DVP-TV

VerticalTermination Cap

12 in.

305 mm

12-1/2 in.

(318 mm)

DVP-TVHW

VerticalTermination Cap (Highwind)

16-7/8 in.

(429 mm)

12 in.

(305 mm)

12-1/8 in. (314 mm)

1-5/8 in. (41 mm)

High Performance Cap

Figure 16.7 DVP vent components

7-1/8 in.

(181 mm)

DVP-HPC

8-3/4 in.

(222 mm)

14 in.

(356 mm)

1 in.

(25 mm)

14 in.

(356 mm)

7-1/4 in.

(184 mm)

3/8 in. (10 mm)

1 in. (25 mm)

7-3/4 to 10-3/8 in.

(197 to 264 mm)

DVP-FBHT

FireBrickTermination Cap

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 73

Page 74

B. Vent Components Diagrams (continued)

15 in.

(381 mm)

8-1/8 in.

(206 mm)

DVP-HRC-SS

13 in.

(330 mm)

Figure 16.8 DVP vent components

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0874

Page 75

B. Vent Components Diagrams (continued)

6-1/2 in. 165 mm

8-3/4 in. 222 mm

6-5/8 in. 168 mm

SLP45

45° Elbow

6 in.

152 mm

6-1/2 in. 165 mm

9-1/4 in. 235 mm

6-5/8 in. 168 mm

9-7/8 in. 251 mm

SLP90

90° Elbow

Effective

Height/ Length

SLP-PIPE

Effective Height/Length Pipe

SLP4 4 102

SLP6 6 152 SLP12 12 305 SLP24 24 610 SLP36 36 914 SLP48 48 1219 SLP6A 2 - 6 51 - 152

SLP12A 2 - 12 51 - 305 SLP-FLEX-2 24 610 SLP-FLEX-3 36 914 SLP-FLEX-5 60 1524

SLP-FLEX-10 120 3048

inches mm

EFFECTIVE HEIGHT/

LENGTH

SLP-FLEX-PIPE

26 in.

660 mm

DVP-HSM-B

Extended Heat Shield

SLP-HVS

Horizontal Pipe

RF4-8

Roof Flashing

Support

Figure 16.9 SLP Series Vent Components

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 75

SLP-FS

Ceiling Firestop

SLP-WS

Wall Shield Firestop

Page 76

B. Vent Components Diagrams (continued)

SLP-DCF-BK

Ceiling Firestop

Black

SLP-TRAP1

Horizontal

Termination Cap

SLK-SNKD

Snorkel

Termination Cap

SLP-CCS-BK

Cathedral Ceiling

Support Box-Black

SLP-TRAP2

Horizontal

Termination Cap

SLP-TVHW

Vertical

Termination Cap

PVK-80

(For use with IPI and DSI appliances only.)

SL-2DVP

Adapter

SLP-FLEX-TRAP

Horizontal

Termination Kit

Figure 16.10 SLP Series Vent Components

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0876

SLP90

DVP-2SL

Adapter

SL-2DVP

ASSEMBLY

SLP-WT-BK

Wall Thimble-Black

DVP-FBHT

Page 77

C. Service Parts

ST-36TRB-IPI

Service Parts Diagram

Beginning Manufacturing Date: Nov. 2008

Ending Manufacturing Date:______

Log Set Assembly

Part number list on following page.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 77

Page 78

C. Service Parts List ST-36TRB-IPI

IMPORTANT: THIS IS DATED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.

ITEM DESCRIPTION COMMENTS PART NUMBER

Log Set Assembly A Log A B Log B

C Log C D Log D

1 Log 1 2 Log 2 3 Log 3 4 Sheetrock Ledge



6 Burner NG, LP 2128-007 7 Base Pan/Grate Assembly 8 Glass Door Assembly Qty 2 req 9 Thermostat Wire

10 Pilot Shield 11 Junction Box 12 Junction Box Bracket

Refractory Left

Refractory Right

LOGS-2128 SRV2128-701 SRV2128-702 SRV2128-703 SRV2128-706 SRV2128-704 SRV2128-705 SRV2128-707 2128-118 2129-017 2129-016

2128-005 GLA-750TR 2118-170 2128-124 4021-013 2128-128

Stocked

at Depot

Y Y

Exhaust Bafﬂ e

Flue Restrictor

Gasket Assembly

Contains Vent, Seal Cap, Burner Neck, Shutter Bracket and Valve Plate Gaskets

Glass Latch Assembly Qty 8 req

Lava Rock

Mineral Wool

Surround Overlay (contains overlay for top, bottom and sides) SRV2128-FACE

Touch Up Paint

Conversion Kit NG

Conversion Kit LP

Pilot Oriﬁ ce NG 593-528 Pilot Oriﬁ ce LP 593-527 Regulator NG NGK-DXV Regulator LP LPK-DXV

Additional service part numbers appear on following page.

385-105 385-128

2128-081

386-122A 2005-790 050-721

TUP-GBK-12

NGK-MS36 LPK-MS36

Y Y Y Y Y Y

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0878

Page 79

C. Service Parts

PIER-36TRB-IPI

Service Parts Diagram

Beginning Manufacturing Date: Nov. 2008

Ending Manufacturing Date: ______

Log Set Assembly

Part number list on following page.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 79

Page 80

C. Service Parts List PIER-36TRB-IPI

ITEM DESCRIPTION COMMENTS PART NUMBER

Log Set Assembly A Log A B Log B

C Log C D Log D

1 Log 1 2 Log 2 3 Log 3 4 Sheetrock Ledge (side) 5 Refractory Panel



6 Burner NG, LP 2128-007 7 Pilot Shield 8 Base Pan/Grate Assembly 9 Glass Door Assembly (Side) Qty 2 req

10 Thermostat Wire

11 Junction Box 12 Junction Box bracket 13 Glass Door Assembly (End) 14 Sheetrock Ledge (End)

LOGS-2128 SRV2128-701 SRV2128-702 SRV2128-703 SRV2128-706 SRV2128-704 SRV2128-705 SRV2128-707 2130-118 2129-016

2128-124 2128-005 GLA-750TR 2118-170 4021-013 2128-128 GLA-2130 2130-126

Stocked

at Depot

Y Y Y

Exhaust Bafﬂ e Flue Restrictor Glass Latch Assembly Qty 8 req Gasket Assembly

Contains Vent, Seal Cap, Burner Neck, Shutter Bracket and Valve Plate Gaskets

Lava Rock Mineral Wool Surround Overlay (contains overlay for top, bottom and sides) SRV2130-FACE Touch Up Paint

Conversion Kit NG Conversion Kit LP

Pilot Oriﬁ ce NG 593-528 Pilot Oriﬁ ce LP 593-527 Regulator NG NGK-DXV Regulator LP LPK-DXV

Additional service part numbers appear on following page.

385-105 385-128 386-122A

2128-081

2005-790 050-721

TUP-GBK-12

NGK-MS36 LPK-MS36

Y Y Y Y Y Y

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0880

Page 81

C. Service Parts

LCOR-36TRB-IPI

Service Parts Diagram

Beginning Manufacturing Date: Nov. 2008

Ending Manufacturing Date:______

Log Set Assembly

Part number list on following page.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 81

Page 82

C. Service Parts List LCOR-36TRB-IPI

ITEM DESCRIPTION COMMENTS PART NUMBER

Log Set Assembly A Log A B Log B C Log C D Log D

1 Log 1 2 Log 2 3 Log 3 4 Glass Door Assembly (End) 5 Burner NG, LP 2128-007 6 Pilot Shield 7 Base Pan/Grate Assembly 8 Glass Door Assembly (Side) 9 Thermostat Wire

10 Junction Box

11 Junction Box Bracket

12 Sheetrock Ledge (Side)

LOGS-2128 SRV2128-701 SRV2128-702 SRV2128-703 SRV2128-706 SRV2128-704 SRV2128-705 SRV2128-707 GLA-2130

2128-124 2128-005 GLA-750TR 2118-170 4021-013 2128-128 2130-118

Stocked

at Depot

Y Y

Y Y Y

Exhaust Bafﬂ e

Flue Restrictor

Glass Latch Assembly Qty 4 req

Gasket Assembly

Contains Vent, Seal Cap, Burner Neck, Shutter Bracket and Valve Plate Gaskets

Lava Rock

Mineral Wool



Additional service part numbers appear on following page.

Refractory (End)

Sheetrock Ledge (End)

Surround Overlay (contains overlay for top, bottom and sides) SRV2132-FACE

Touch Up Paint

Conversion Kit NG

Conversion Kit LP

Pilot Oriﬁ ce NG 593-528 Pilot Oriﬁ ce LP 593-527 Regulator NG NGK-DXV Regulator LP LPK-DXV

385-105 385-128 386-122A

2128-081

2005-790 050-721 2129-016 2130-126

TUP-GBK-12

NGK-MS36 LPK-MS36

Y Y Y Y Y Y

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0882

Page 83

C. Service Parts

RCOR-36TRB-IPI

Service Parts Diagram

Beginning Manufacturing Date: Nov. 2008

Ending Manufacturing Date: ______

Part number list on following page.

Log Set Assembly

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 83

Page 84

C. Service Parts List RCOR-36TRB-IPI

ITEM DESCRIPTION COMMENTS PART NUMBER

Log Set Assembly A Log A B Log B C Log C D Log D

1 Log 1 2 Log 2 3 Log 3 4 Sheetrock Ledge (Side)



5 Refractory (End) 6 Burner NG, LP 2128-007 7 Pilot shield 8 Base Pan/Grate Assembly 9 Glass Door Assembly (Side)

10 Thermostat Wire

11 Junction Box 12 Junction Box bracket 13 Glass Door Assembly (End) 14 Sheetrock Ledge (End)

LOGS-2128 SRV2128-701 SRV2128-702 SRV2128-703 SRV2128-706 SRV2128-704 SRV2128-705 SRV2128-707 2130-118 2129-016

2128-124 2128-005 GLA-750TR 2118-170 4021-013 2128-128 GLA-2130 2130-126

Stocked

at Depot

Y Y Y

Exhaust Bafﬂ e Flue Restrictor Gasket Assembly

Contains Vent, Seal Cap, Burner Neck, Shutter Bracket and Valve Plate Gaskets

Glass Latch Assembly Qty 4 req Lava Rock Mineral Wool Surround Overlay (contains overlay for top, bottom and sides) SRV2132-FACE Touch Up Paint

Conversion Kit NG Conversion Kit LP

Pilot Oriﬁ ce NG 593-528 Pilot Oriﬁ ce LP 593-527 Regulator NG NGK-DXV Regulator LP LPK-DXV

Additional service part numbers appear on following page.

385-105 385-128

2128-081

386-122A 2005-790 050-721

TUP-GBK-12

NGK-MS36 LPK-MS36

Y Y Y Y Y Y

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0884

Page 85

Service Parts

ST-36TRB-IPI, PIER-36TRB-IPI,

LCOR-36TRB-IPI, RCOR-36TRB-IPI

Intermittent Pilot Ignition

Valve Assembly

Valve Assembly Diagram/ Parts List

Beginning Manufacturing Date: Nov. 2008

Ending Manufacturing Date: ______

ITEM DESCRIPTION COMMENTS PART NUMBER

1 Shutter Bracket Assembly 2

Pilot Assembly NG Pilot Assembly LP

2118-121 Y 2090-012 Y

2090-013 Y 3 Flexible Gas Connector 530-302A Y 4 Flex Ball Valve Assembly 302-320A Y

Oriﬁ ce NG (#32C) Oriﬁ ce LP (#50C) Valve NG 750-500 Y Valve LP 750-501 Y

582-832 Y

582-850 Y

7 Module 593-592 Y 8 Battery Pack 593-594A Y 9 Module Wire Assembly 593-590A Y

10 3 Volt Transformer 593-593A Y 11 Valve Bracket

2 in Jumper Wires

2118-104

2012-206 Y

Stocked

at Depot

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev B. • 10/08 85

Page 86

D. Contact Information

Heat & Glo, a brand of Hearth & Home Technologies Inc.

20802 Kensington Boulevard, Lakeville, MN 55044

www.heatnglo.com

Please contact your Heat & Glo dealer with any questions or concerns.

For the location of your nearest Heat & Glo dealer,

please visit www.heatnglo.com.

- NOTES -

________________________________________________________________________________

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating and maintenance instructions included.

• Read, understand and follow these instructions for safe installation and operation.

• Leave this manual with party responsible for use and operation.

This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, 6769426, 6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending.

Heat & Glo • ST-36TRB-IPI, PIER-36TRB-IPI, LCOR-36TRB-IPI, RCOR-36TRB-IPI • 2128-900 Rev. B • 10/0886

Hearth and Home Technologies LCOR-36TRB-IPI, PIER-36TRB-IPI, ST-36TRB-IPI, RCOR-36TRB-IPI User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual