Hearth and Home Technologies RC200 User Manual
RC200
IntelliFire Plus™ Multifunction Remote Control
Installation & Operating Instructions
Hearth & Home T echnologies disclaims any responsibility for ,
and the warranty will be voided by, the following actions:
• Installation and use of any damaged system component.
• Modifi cation of the system component.
• Installation other than as instructed by Hearth & Home
Technologies.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Any such action may cause a fi re hazard.
• Read, understand and follow these instructions for safe
installation and operation.
Introduction
The RC200 multifunctional wireless control with docking station is designed to control constant pilot feature,
fl ame height, blower speed and to turn your gas fi re-
place on and off. The RC200 remote control is only for
use with the Hearth & Home Technologies IntelliFire
Plus™ system (IPI).
FCC Requirements
WARNING! Risk of Fire! Changes or modifi cations to
this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate
the equipment.
Canadian Equipment Requirements
This digital apparatus does not exceed the (Class A/ Class
B) limits for radio noise emissions from digital apparatus
set out in the Radio Interference Regulations of the Canadian Department of Communications. Le present appareil
numerique n’emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques (de
la class A/de la class B) prescrites dans le Reglement sur
le brouillage radioelectrique edicte par le ministere des
Communications du Canada.
This device complies with RSS-210 of Industry and Science
Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired operation of the device.
Installation Precautions
This control is tested and safe when installed in accordance with this installation manual. Do not install any
components that may be damaged.
Do not modify , disassemble, or substitute any of the components included with this kit. Installation of this unit must
be done by a qualifi ed service technician.
Placement of this remote control may affect performance.
An assessment of the space should be done prior to installation for optimum performance.
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Contact the dealer or an experienced radio TV technician for help.
Hearth & Home Technologies • RC200 Multifunction Remote Control • 2166-392 Rev. B • 9/10
Determine Location
Determine the location for the remote control. The selected
location should be in the same space as the gas fi replace
with visual sight of fi replace. The remote control must be
placed within 30 feet of the fi replace but should not be
exposed to extreme heat.
The RC200 is approved for interior installation and should
always be placed under weather resistant cover when used
in exterior applications.
• Keep remote control out of reach of children.
1
RED LED
AUX200
CABLE
Installation of Remote Control Housing
CAUTION! Risk of Fire! DO NOT install damaged or
modifi ed components. Warranty will be voided if damaged
or modifi ed components are installed.
Kit components: One remote control, two #6 screws, two
wall anchors, one A23 battery and one AUX200 module (if
purchased retail).
1. Remove remote control components from packaging.
2. Remove battery cover from the back of the remote by
sliding it down and install A23 battery.
T o prevent unintended operation when not using your fi re-
place for an extended period of time (summer months,
vacation, trips, etc):
• Remove battery from remote control.
• Unplug switching adapter and remove back-up batteries.
3. Secure the remote control housing on a fl at wall sur-
face using the two screws and wall anchors provided.
See Figure 1.
5. Close the housing door and press the power button.
The red light illuminates if the battery was properly installed. See Figure 3.
RED LED
Figure 3. Mounting Remote Control Housing
AUX200 Module Installation
• Control Module should be set in the OFF position before
any components are installed.
• Insert the 4 hole harness from the AUX200 module into
the 4 pin plug on the control module. See Figure 4.
Figure 1. Mounting Remote Control Housing
4. Place remote control inside housing. See Figure 2.
AUX200
CABLE
Figure 4. AUX 200 module installation
Fan Installation
• Insert the 3 prong plug from the fan into the receptacle
located in the AUX200 module. See Figure 5.
Figure 2. Remote in Housing
2
Hearth & Home Technologies • RC200 Multifunction Remote Control • 2166-392 Rev. B • 9/10
Loading...