HealthRider HRCCE69020 Owner's Manual
Model No. HRCCE69020
www.healthrider.com
Visit our website at
Serial No.
Serial
Number
Decal
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you have
questions, or if there are missing
parts, please call:
1-888-936-4266
Mon.–Fri. 8h00 until 18h30 EST
(excluding holidays).
USER’S MANUAL
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Keep this manu
al for future reference.
-
TABLE OF CONTENTS
IMPOR
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
HOW TO USE THE ELLIPTICAL CROSSTRAINER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
CONDITIONING GUIDELINES
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
HOW TO ORDER REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
TANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
HealthRider is a registered trademark of ICON Health & Fitness, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:To reduce the risk of serious injury, read the following important precau-
tions before using the elliptical crosstrainer.
1. Read all instructions in this manual before
using the elliptical crosstrainer
2. It is the responsibility of the owner to ensure
that all users of the elliptical crosstrainer
are adequately informed of all precautions.
3. The elliptical crosstrainer is intended for
home use only. Do not use the elliptical
crosstrainer in a commercial, rental, or institutional setting.
4. Place the elliptical crosstrainer on a level
surface, with a mat beneath it to protect the
floor or carpet. Keep the elliptical crosstrainer indoors, away from moisture and dust.
5. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
6. Keep children under 12 and pets away from
the elliptical crosstrainer at all times.
7. The elliptical crosstrainer should not be
used by persons weighing more than
115 kg (250 lbs).
.
8. Wear appropriate exercise clothing when
using the elliptical crosstrainer
athletic shoes for foot protection.
9. Always hold the handgrip pulse sensor or the
handlebars when mounting, dismounting, or
using the elliptical crosstraine r.
10. The pulse sensor is not a medical device.
Various factors, including the user’s movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exerci se aid in determining heart rate
trends in general.
11. Keep your back straight when using the elliptical crosstrainer; do not arch your back.
12. If you feel pain or dizziness at any time
while exercising, stop immediately and
begin cooling down.
13. When you stop exercising, allow the pedals
to slowly come to a stop.
. Always wear
WARNING:Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON assumes no responsibility for personal injury or
property damage sustained by or through the use of this product.
3
BEFORE YOU BEGIN
Congratulations for selecting the new HealthRider
C860e elliptical crosstrainer. The C860e elliptical
crosstrainer is an incredibly smooth exerciser that
moves your feet in a natural elliptical path, minimizing
the impact on your knees and ankles. And the unique
C860e features adjustable resistance and a state-ofthe-art console to help you get the most from your
exercise.
For your benefit, read this manual carefully before
you use the elliptical crosstrainer. If you have
questions after reading this manual, call our Customer
Console
Handlebar
®
Service Department toll-free at 1-888-936-4266,
Monday through Friday, 8h00 until 18h30 EST
(excluding holidays). To help us assist you, note the
product model number and serial number before calling. The model number is HRCCE69020. The serial
number can be found on a decal attached to the elliptical crosstrainer (see the front cover of this manual
for the location of the decal).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Water Bottle Holder*
Bookrack
Handgrip Pulse Sensor
FRONT
Upright Knob
Wheel
Leveling Foot
Pedal
BACK
Pedal Disk
LEFT SIDE
*No water bottle
is included
4
ASSEMBLY
M4 x 16mm
Screw (66)–2
M10 x 27mm
Screw (71)–3
M10 Nylon
Locknut (29)–4
M8 Nylon
Locknut (46)–4
M6 x 25mm
Screw (63)–1
Plastic
Washer (19)–4
M6 x 20mm Pedal
Screw (20)–4
M10 x 25mm
Patch Screw (52)–2
M10 Split
Washer (70)–3
M10 Bracket
Washer (94)–2
M8 x 45mm Button
Bolt (83)–4
M10 Spacer
(53)–2
M10 Bolt Set (27)–2
M10 x 112mm Carriage Bolt (34)–4
M8 x 19mm Shoulder
Screw (22)–2
Assembly requires two persons. Place all parts of the elliptical crosstrainer in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed.
In addition to the included allen wrenches, assembly requires a phillips screwdriver , an
adjustable wrench , and a rubber mallet .
As you assemble the elliptical crosstrainer, use the drawings below to identify the small parts used in assembly.
The number in parenthesis below each drawing refers to the key number of the part, from the PART LIST on
page 22. The second number refers to the quantity used in assembly.
pre-assembled for shipping. If a part is not in the parts bag, check to see if it has been pre-assembled.
Note: Some small parts may have been
5
1. Identify the Front Stabilizer (3), which has Wheels (32)
attached to it. While another person lifts the front of the
Frame (1), attach the Front Stabilizer to the Frame
with two M10 x 112mm Carriage Bolts (34) and two
M10 Nylon Locknuts (29).
Stabilizer is turned so the Wheels are not touching
the floor.
Make sure that the Front
1
34
32
32
3
1
29
2. While another person lifts the back of the Frame (1),
attach the Rear Stabilizer (4) to the Frame with two
M10 x 112mm Carriage Bolts (34) and two M10 Nylon
Locknuts (29).
3. While another person holds the Upright (2) in the posi-
tion shown, connect the Upper Wire Harness (86) to
the Lower Wire Harness (87). Carefully pull the
upper end of the Upper Wire Harness to remove
any slack. While holding the upper end of the
Upper Wire Harness, insert the Upright into the
Frame (1). Do not pinch the Wire Harnesses.
Next, turn the Upright Knob (91) counterclockwise sev-
eral turns. Pull the Knob, slide the Upright (2) down
until the Knob is aligned with one of the four adjustment hole s, and then release the Knob. Do not tighten
the Knob yet.
2
29
4
29
1
3
Make sure the
Wire Harnesses
(86, 87) do not
get pinched and
damaged during
this step.
2
34
4. Connect the wire harness on the Handgrip Pulse
Sensor (81) to the indicated wire harness on the
Console (5). Insert both wire harnesses into the opening in the bottom of the Console.
Refer to the inset drawing. Insert the metal tube on the
Handgrip Pulse Sensor (81) into the metal bracket
inside the Console (5) as shown. Be careful not to
pinch the wire harnesses. Align the holes in the metal
tube with the holes in the metal bracket, and tighten two
M4 x 16mm Screws (66) into the indicated holes.
Snap the bookrack onto the Console (5) in the location
shown.
86
87
1
91
4
Bookrack
Wire Harnesses
5
66
Bracket
Tube
81
66
5
81
6
5. The Console (5) requires four “D” batteries (not included); alkaline batteries are recommended. Refer to the
inset drawing. Press the tab on the battery cover, and
lift off the battery cover. Insert four batteries into the
battery compartment.
are oriented as shown by the diagram inside the
battery compartment. Reattach the battery cover.
While another person holds the Console (5) in the
position shown, connect the wire harness on the
Console to the Upper Wire Harness (86). Insert the
excess wire harness into the Upright (2). Next, attach
the Console to the Upright with three M10 x 27mm
Screws (71) and three M10 Split Washers (70).
careful to avoid pinching the wire harnesses.
Make sure that the batteries
Be
5
5
Tab
Battery
Cover
Batteries
5
Wire
Harness
86
71
70
71
2
71
70
6. Identify the Left Handlebar (9), which is marked with a
. Insert the Left Handlebar into one of the
sticker
Handlebar Legs (79);
Leg is turned so the hexagonal holes are on the
indicated side
Handlebar Leg with two M8 x 45mm Button Bolts (83)
and two M8 Nylon Locknuts (46).
Nylon Locknuts are inside of the hexagonal holes.
Do not fully tighten the Button Bolts yet.
Apply a small amount of the included grease to the left
and right axles on the Upright (2).
Carefully slide an Upright Spacer (26), a Handlebar
Spacer (25), the Left Handlebar (9), and a Handlebar
Cap (23) onto the left axle on the Upright (2) as shown.
Slide an M10 Spacer (53) onto an M8 x 19mm Shoulder
Screw (22), and tighten the Shoulder Screw into the axle.
Attach the Right Handlebar and the other Handlebar Leg
(not shown) in the same way.
. Attach the Left Handlebar to the
make sure that the Handlebar
Make sure that the
6
Grease
9
2
53
22
23
83
26
25
46
Hexagonal
Holes
79
7. Attach a Pedal (12) to the Left Pedal Arm (15) with two
M6 x 20mm Pedal Screws (20) as shown. Note: The
Pedal can be attached in any of three positions (see
HOW TO ADJUST THE PEDALS AND THE UPRIGHT
on page 9).
Attach the other Pedal (not shown) to the Right Pedal
Arm (not shown) in the same way
Pedals are attached in the same position.
. Make sure that both
7
7
20
12
15
8. Apply a small amount of grease to the axle on the left
Crank Arm (36). Slide the Left Pedal Leg (14) onto the
axle. Slide an M10 Bracket Washer (94) onto an M10 x
25mm Patch Screw (52), and tighten the Patch Screw
into the axle.
Attach the Right Pedal Leg (not shown) to the right side
of the elliptical crosstrainer in the same way
.
8
Grease
9. Position a Cushion (88) in one of the adjustment holes
in the Left Pedal Leg (14). Set the Left Pedal Arm (15)
on the Cushion, with the end of the Pedal Arm inside of
the angled bracket on the Pedal Leg. Slide a Plastic
Washer (19) between the Pedal Arm and the Pedal
Leg. Insert the long part of the M10 Bolt Set (27)
through the Pedal Leg, Plastic Washer, and Pedal Arm.
Lift the Left Pedal Leg (14) and hold the left Handlebar
Leg (79) inside of the bracket on the Left Pedal Arm
(15). Slide the other Plastic Washer (19) between the
Pedal Arm and the Pedal Leg. Insert the long part of
the M10 Bolt Set (27) through the Handlebar Leg,
Pedal Arm, Plastic Washer, and Pedal Leg. Tighten the
short part of the Bolt Set into the long part.
Attach the Right Pedal Arm (not shown) to the Right
Pedal Leg (not shown) and the right Handlebar Leg
(79) in the same way.
9
Grease
14
19
15
52
63
36
94
2
79
91
79
19
27
Tighten the M6 x 25mm Screw (63) into the Upright (2).
Turn the Upright Knob (91) clockwise until it is tight.
Refer to step 6. Tighten the M8 x 45mm Button Bolts
(83) in the Handlebar Legs (79).
10.Make sure that all parts of the elliptical crosstrainer are properly tightened. Note: Some hardware may
be left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the
elliptical crosstrainer.
27
14
88
8
Loading...