Hayward ColorLogic WFBCUS1100, ColorLogic WFB100 Owner's Manual
\
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Hayward Pool Products
620 Division Street, Elizabeth NJ 07207
Phone (908)-355-7995
www.hayward.com
ColorLogic Bubbler
Owner’s Manual
092619 RevA beta draft1
WFBCUS1100
WFB100
Contents
Before You Begin......................................2
Installation..............................................5
Operation..............................................12
Winterization.........................................12
Warranty................................................18
®
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
1
IMPORTANT SAFETY INSTRUCTIONS
When using this electrical equipment, basic safety precautions should always be followed, including the following:
READ AND FOLLOW ALL INSTRUCTIONS
WARNING - Read and follow all instructions in this owner’s manual and on the equipment. Failure to follow instructions can cause severe injury and/or death.
WARNING – ELECTRIC SHOCK HAZARD. MOUNTING A LUMINAIRE THAT REQUIRES
BONDING OR GROUNDING IN THIS NICHE CAN CAUSE SEVERE INJURY AND/OR DEATH. DO
NOT MOUNT NON-UL LISTED LIGHTS OR ANY LUMINAIRE THAT REQUIRES BONDING OR
GROUNDING IN THIS NICHE.
WARNING – Risk of Electric Shock. Hazardous voltage can shock, burn, and cause
death or serious property damage. All electrical wiring MUST be in conformance with applicable local codes, regulations, and the National Electrical Code (NEC). To reduce the risk
of electric shock, do NOT use an extension cord to connect unit to electric supply. Provide a
properly located electrical receptacle. Before working on any electrical equipment, turn off
power supply to the equipment.
WARNING – Risk of Electric Shock. Opening light can cause shock, burn and severe
injury. Light has no user serviceable parts inside. Do not open light.
NOTICE – This swimming pool product is UL listed for permanently installed pools or
spas only. It is not listed for storable pools or spas. Permanently installed pools and spas
are those constructed in or partially in the ground and all others capable of holding water in
a depth greater than 42 in (1.07 m). Storable pools and spas are those constructed on or
above the ground and capable of holding water to a maximum of 42 in (1.07 m).
WARNING – Electrical shock hazard. Damage to wiring can cause severe injury or
death. To reduce the risk of electric shock replace damaged wiring immediately. Locate
conduit to prevent abuse from lawn mowers, hedge trimmers and other equipment.
SAVE THESE INSTRUCTIONS
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
2
Before You Begin
The Hayward WFB100 ColorLogic® Bubbler has been designed for use with all Hayward Accent
Lights and provides lighted water for small fountains and other water effects. The ColorLogic®
Bubbler must be installed as specified by these instructions. Please follow ALL of the instructions
enclosed with this unit. It is recommended to keep the unit in its original packaging until the site is
prepared for installation.
Compatibility
The Hayward WFB100 ColorLogic® Bubbler is compatible with the following Hayward Accent Light
models:
Hayward ColorLogic® 320
Hayward ColorLogic® 160
Hayward ColorLogic® 320 Network
Hayward ColorLogic® 160 Network
Hayward CrystaLogic® 320
Hayward CrystaLogic® 160
Note that the WFBCUS1100 version comes packaged with one ColorLogic® 320 Accent Light with
a 100’ cord.
What’s Included
Refer to the image and the table on the following page for a list of all items included with the
Hayward WFB100 ColorLogic® Bubbler.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
3
ITEM NO.
QTY.
PART NUMBER DESCRIPTION
1
2
3
4
5
6
7
8
9*
10*
11*
12*
13*
G1-046397
G1-068159
SP1022C
G1-046400
G1-046399
G1-046398
G1-046393
G1-046395
G1-046396
G1-046394
G1-046403
SP0710XZ3
Cardboard Pipe Spacer
Housing
Gunite Shield
1-1/2” Threaded Plug with O-Ring
Plaster Shield
Plaster Ring
Lens
Retaining Ring
ColorLogic Bubbler Nozzle, 1/2”
ColorLogic Bubbler Nozzle, 3/4”
ColorLogic Bubbler Nozzle Nut
ColorLogic Bubbler Nozzle Threaded Plug
Plaster Shield O-Ring (For Winterization Only)
2
1
1
2
1
1
1
1
1
1
1
1
1
--
14* SP1022CZ2
O-Ring For Nozzle and Plug
2
*Comes In Plastic Bag
15* G1-046401 ColorLogic Bubbler Tool 1
4
3
2
10
9
13
11
12
7
8
6
5
1
15
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
4
Exploded View
**Plaster Ring only adjustable during Installation.
8. Retaining
Ring
7. Lens
11. Nozzle Nut
9-10. Adjustable
Nozzle (1/2” or
3/4”)
Accent Light
(included with
WFBCUS1100)
2. Housing
1. Cardboard Spacer
1.5” SCHED
40 Electrical
Conduit (Not
Included)
1.5” SCHED 40
PVC Pipe (Not
Included)
6. Plaster Ring**
14. O-Ring
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
5
Installation
System Overview
The diagram below shows an overview of a fully installed ColorLogic Bubbler system.
**Hayward recommends mounting the ColorLogic® Bubbler no more than 12” below the surface of
the water when installed as a bubbler/fountain for the best combination of water and light.
Determine the location for the ColorLogic® Bubbler. Rough-in plumbing pipe and electrical conduit
by plumbing the water line to the desired pumping system and the electrical line to the Accent
Light junction box as shown above. It is recommended that you use 1.5” SCHED 40 Electrical Conduit for the electrical line. Use the two provided cardboard pipe spacers to ensure proper distance
from the plumbing and electrical pipes (as shown on page 7). Keep the cardboard pipe spacers on
the pipes to make installation of the housing easier later on. If you have lost or discarded the pipe
spacers, note that the distance between the centers of each pipe should be exactly 2.5”.
NOTE: If finite control will be desired, be sure to install an in-line flow control valve to adjust the
height and flow of the water stream from the ColorLogic® Bubbler.
FLOWLIGHT
Accent Light
Adjustable Nozzle
(1/2” or 3/4”)
From 12V Input
Junction Box
From Pool or Spa Water Supply +
optional in-line flow control valve
Plaster
Gunite
Dirt/Gravel
2-12” **
1.5” SCHED 40
Electrical Conduit
1.5” SCHED 40
PVC Pipe
Loading...