Hayward AquaNaut Troubleshooting Manual

Hayward AquaNaut

®

®

Troubleshooting Guide

Copyright 2015 Hayward Industries Inc.

Table of Contents

Safety Precautions………………………………… ……….. Page 1

Two Wheeled vs. Four Wheeled Versions……….……….. Page 2

RPMs ………………………………………………. ……….. Pages 3 - 4

Checking for obstructions in cleaner…………...................Pages 5 - 7

Cleaner does not move…………………………………….. Page 8

Cleaner moves too slow / Right wheel doesn’t turn……... Page 9

Right wheel skips / Cleaner hose coiling…………………. Page 10
Cleaner not cleaning entire pool…………………………… Page 11
Cleaner climbing too high…………………………………... Page 12

Cleaner floats / Turbine vanes pop out…………………… Page 13

Wheels are wobbly / cleaner falls on its side…………….. Page 14
Changing the turbine hub…………………………………...Pages 15 - 20

• Never use your hand to verify the amount of vacuum
at the skimmer or dedicated suction line.

• Keep hands and fingers away from the access cover

and any moving part while the cleaner is operating.

• Never operate the cleaner with people or pets in the

pool.

• Never operate the cleaner unless cleaner is
submerged under the water.

• A dedicated suction line should have a Vac Lock
installed for safety.

Safety Precautions

Page 1

Two Wheeled Version (200) vs. Four

Wheeled Version (400)

An easy way to determine which model is recommended for a given pool is to
imagine a 40’ long pool. If the suction port or skimmer is half way from one end, then

the 2 Wheel model will be the right one.

If the suction port is all the way at one end or you have a very deep end (diving pools)
the 4 Wheel model would be better suited for the pool.

The 2 Wheel unit comes with 33’ of hose (9 vacuum and one leader hose). You can

safely add two lengths of hose if needed. The 4 Wheel unit comes with 40’ of hose
(11 vacuum and one leader hose). You can add quite a few lengths to it, but at some
point there will be two problems. 1) the hoses will outweigh the cleaner and 2) the
more hoses you add, the more suction is lost to the head.

The 2 Wheel has a steering cam that makes it turn 5 times in a cycle. So it turns more
often to cover an average sized pool. The 4 Wheel has a cam that makes only 3
turns, so that the unit goes straight longer in order to cover a larger pool.

A 2 Wheel unit that needs more straight run can replace the 2 Wheel Cam

(PVXH036009) with a 4 Wheel Cam (PVXH010009).

Page 2

RPMs

The most common problem is that the cleaner is not getting enough suction, or is

getting too much suction, which causes improper wheel speed.

Common symptoms of HIGH RPMs would be:

• Cleaner is falling on its side (this can also be floats on leader hose missing).

• Cleaner is doing wheelies and tipping backward.

• Cleaner is slipping a little because it can’t pull the hose fast enough.

• Cleaner climbs out and sucks air constantly (this can also be worn tires).

• Cleaner is not covering pool.

Common symptoms of LOW RPMS would be:

• Cleaner is not covering pool.

• Cleaner gets stuck in corners or hangs up on objects in the pool.

• Cleaner is falling on its side (this can also be floats on leader hose missing).

• Cleaner starts and stops. The rpms are so low that the friction from the floor

stops the cleaner.

• Hoses coil (this can also be the swivel on the head is dirty).

Page 3

Step 1: Looking from the rear of the cleaner with the cleaner under water,
count how many times the right front wheel hump turns around in one minute.
Wheel RPM should be between 11 and 14.

RPMs

Step 2: If the wheel RPM is not between 11 and 14, the suction to the cleaner

must be adjusted to allow for proper operation.

Page 4

Checking For Obstruction in Cleaner

Step 1: Rotate the Right

front wheel forward. If it

doesn’t move, there’s an

obstruction. Do not

attempt to turn Left

wheel.

Step 2: Remove the
two screws that hold the
Handle.

Step 3: Remove the
Handle.

Page 5