Page 1
RS 17/102H
HERITAGE TRACTOR
Code149D
INSTRUCTION BOOK
(English Version)
Code From serial No.
149D 260000001
Issue 01/11/05
MANUAL PART NO: 111-0442 (A)
Page 2
1
2
3
5
4
6
7
8
2
Page 3
9 10
11
13
12
Ø19 x Ø26
Ø20 x Ø42
14
15
16
3
Page 4
ø7
2
1
17
19
18
20
Ø 6 (2x)
M6 x 45 (2x)
21
23
2
M6 (2x)
Ø 6 x Ø 12 (4x)
22
24
1
2
1
4
Page 5
3
1
Ø6 x 18Ø
25
27
2
Ø6 x Ø12
26
28
29
31
1
2
3
4
30
1
2
3
32
5
Page 6
33
34
11
35
1
2
3
O
I
II
2
36
0½¾ ¼
37
39
38
1
0
I
2
40
6
Page 7
ON
OFF
1
2
1
1
41
43
2
1
1
2
3
42
44
45
7
Page 8
Before assembly and start of operation,
please read the operating instructions at all
Dear Customer,
You have bought a totally tested quality product. However, should you
have any reason for complaints, please get in touch with your dealer,
stating the code and serial number (see nameplate).
costs and comply with them.
LIST OF CONTENTS
Manufacturer
Introduction.................. ........................................... .................. GB 8
Intended use............................................................................. GB 8
Meaning of symbols indicated on the mower.......................... GB 8
Safety precautions.................................................................. GB 9
Unpacking Lawntractor………………………………………….. GB 10
Assembly................................................................................ GB 11
First operation.......................................................................... GB 13
Operating elements.................................................................. GB 13
Start of operation..................................................................... GB 14
Care and maintenance............................................................ GB 16
Starter battery......................................................................... GB 18
Storage in winter...................................................................... GB 19
Trouble Shooting.................................................................... GB 20
Warranty................................................................……...……. GB 21
INTRODUCTION
Dear customer,
You have purchased a new machine. We want to thank you for the trust
that you put into our quality products and hope that you will have much
pleasure from working with your new machine.
Before putting the machine into operation for the first time, please
familiarise yourself with the contents of these operating instructions. If
the machine is operated by people without sufficient qualifications or not
according to the intended purpose, use of the machine may be
dangerous. Please pay attention to the accident prevention directives.
Please pay attention to the safety instructions contained in these
operating instructions and to the safety instructions on the machine.
Due to ongoing improvements of the product, the information contained
in this manual is subject to alterations without the manufacturer being
obliged to notify or to update, under the proviso that the essential
properties for safety and operation do not change. In cases of doubt,
please do not hesitate to contact your dealer.
INTENDED USE
This lawnmower is only intended for mowing in private gardens with a
maximum inclination of 10° (18%) - not for public parks, sports grounds
or in farming or forestry. Other kinds of use are only permitted with
original spare parts.
Any other use is regarded as being misuse and results in forfeiture of the
guarantee and rejection of any responsibility for damage to the user of
third parties on the part of the manufacturer.
Working hours for lawn tractors:
Please observe the local directives for the operation of lawnmowers.
GB
MEANING OF SYMBOLS INDICATED ON THE
MOWER
Read operating instructions before
start of operation.
Keep other people out of the danger
zone.
Pull the ignition plug out before
maintenance and repair work.
Do not use on slopes above 10°
(18%).
Attention, danger!
Keep hands and feet away from the
cutting gear.
While mowing, keep other people, in
particular children and animals,
away from the working area.
Danger: do not go here.
GB 8
Page 9
GB
SAFETY PRECAUTIONS
1. General remarks
1.1 Read the operating instructions carefully. Familiarise yourself with
the proper use of the machine.
1.2 People under 16 or people who have not read the operating
instructions are not allowed to use the machine.
1.3 Do not operate the machine when there are others, in particular
children or animals, in the area. The person using the machine is
responsible for third parties in the working area of the machine.
1.4 The person using the machine is responsible for accidents
involving other people or their property.
1.5 Please keep these operating instructions for later use.
1.6 The lawn tractor does not have approval according to the Highway
Code. You are therefore not allowed to drive on public ways and
roads with it.
1.7 Never mow on slopes with an inclination of more than 10° (18%).
1.8 No passengers may be transported on the machine.
2. Preparations
2.1 Always wear sturdy shoes and long trousers while mowing. Never
go barefoot or wear open sandals.
2.2 Completely check the area on which the machine is to be used and
remove any stones, sticks, wires, bones and other foreign objects.
Always watch out for foreign objects when mowing.
2.3 – Petrol is to be poured in before starting the engine.
WARNING! Petrol is highly flammable!
– Only keep petrol in the containers designed for this purpose.
– Only fill the machine in the open and do not smoke when filling
the machine.
– The tank may not be opened or petrol topped up while the engi
ne is running or when the machine is hot.
– If petrol has been spilt, do not start the engine. Instead, remove
the mower from the area contaminated with petrol. The spilt pe
trol must be sucked or wiped off the engine and the housing with
a cloth. No attempts at ignition may be made until the vapours
have disappeared.
– Use a funnel or a filling tube when pouring in petrol so that no
fuel can leak onto the engine or onto the lawn.
– For safety reasons, replace the tank lid and the petrol tank if they
are damaged.
2.4 The exhaust and the area around the exhaust can reach
temperatures of up to 80°.
ATTENTION: danger of burning!
Replace damaged silencers.
2.5 Before use, always make a visual check to see if the blade, the
fastening bolts or the entire cutting unit are worn or damaged. In
order to avoid an imbalance, worn or damaged blades must be
replaced with new ones.
2.6 Ensure that the movement of one blade can lead to rotations of the
other blades when mowing with more than one blade.
2.7 An examination by an expert is necessary if the machine stops
immediately, e.g. after impact with an obstacle (damage to the drive
shaft, bent blades etc.).
3. Instructions for use
3.1 The combustion engine may not be operated in enclosed rooms in
which dangerous fumes can collect - danger of poisoning!
3.2 Only mow your lawn in daylight or in good illumination. Please
observe any local directives about when you are allowed to use the
machine (see operating times for lawn tractors).
3.3 Before starting the machine, switch off the mowing appliance, put
the drive into neutral and operate the parking brake.
3.4 Please remember that there are no "safe slopes". Mowing slopes
with a lawn requires special attention. In order to protect yourself
against tipping over, you should:
– not stop or start suddenly if you are moving up or down the
slope,
– suppress the clutch slowly, leave the clutch depressed, in parti
cular when driving down the slope,
– keep the speed low on slopes and in tight bends,
– pay special attention to hills, recesses and other invisible
dangers,
– never mow transverse to the slope if it has an inclination of more
than 10°.
3.5 Always pay attention to road traffic when you are crossing roads or
working in the vicinity of roads.
3.6 When driving the tractor, pay attention to low-hanging obstacles
(branches, washing lines etc.) which can injure the driver.
3.7 Switch the mowing appliance off when driving off the lawn, lift it to
the highest cutting position.
3.8 Never operate lawn tractors with a damaged housing or defective
protective devices (e.g. grass box etc.).
3.9 Before leaving the driver's seat:
– switch the mowing appliance off and wait until the blades come
to a standstill,
– switch the engine off and remove the ignition key.
3.10 Disengage the drive, turn the engine off and pull out the spark plug
connector or the ignition key
– before eliminating blockages or obstructions in the discharge
channel
– before checking or cleaning the mower or doing any other work
on it
– if a foreign body is hit. Look for damage to the machine and
have the necessary repairs done before you start it again;
– if the mower starts to vibrate unusually severely, an
immediate check is necessary.
– whenever you leave the mower unattended or transport it
– before filling up with petrol
– before removing the grass box.
3.11 The basic setting of the engine in the factory is correct and must
not be altered.
3.12 Start and operate the starting switch carefully (see Chapter
"Starting the engine"). Make sure that your feet are at a safe
distance from the blade.
3.13 Do not tip the mower when starting or turning the engine on.
3.14 Do not start the engine if anyone is standing in front of the
discharge channel.
3.15 Keep your hands and feet out of the area of the rotating blade.
Keep other people away from the discharge channel when the
blade is rotating.
3.16 Never use a lawn tractor with a rear discharge without a grass box
or a vapour discharge.
GB 9
Page 10
4. Instructions for maintenance and storage
4.1 Make sure that the nuts, bolts and screws are tight.
4.2 Be careful when adjusting - danger of injuries. Do not trap your
fingers between the housing and the blade. Wear protective gloves.
4.3 Never store the lawn tractor with fuel in the tank inside a building in
which petrol fumes can possibly come into contact with naked
flames or with sparks
- danger of explosion!
4.4 Only empty the petrol tank in the open.
4.5 Allow the engine to cool down before you put the machine into an
enclosed area.
4.6 Avoid the risk of a fire by keeping the engine and the exhaust free
of grass, leaves and grease (oil).
4.7 Check regularly to make sure that the grass box is in a satisfactory
condition.
4.8 For safety's sake, worn or damaged parts must be replaced
immediately.
4.9 Replacement blades and additional appliances may only be
mounted on the lawn tractors intended for this purpose according to
the manufacturer's instructions. This is the only way to maintain the
safety and the performance of your lawn tractor.
4.10 Please ensure that the maintenance, checking and sharpening of
the blade is only done by an authorised dealer.
4.11 Only use original replacement blades.
We would point out that we are not liable according to the Product
Liability Act for damage caused by our machine as a result of
a) improper repairs not carried out by our authorised service
dealer,
b) or if ORIGINAL SPARE PARTS are not used as replacement
parts.
GB
Unpacking Lawntractor
The lawntractor will be delivered on a solid wood pallet.
To remove the packing, place the pallet on a level surface.
Please follow the sequence for unpacking and for the respective
wheel locks.
The numbers to the left of the text, e.g. , refer to the
illustrations in the picture section of these operating instructions.
1
2
3
4
5
Now you can begin mounting equipment.
Open cardboard packing at top.
Remove staples and take off cardboard packing upward.
Remove enclosed parts and packing materials.
Remove wooden hoop.
Remove front laths.
Remove wooden blocks.
Remove all nails on the pallet.
Move mowing unit into highest position.
See operating instructions under:
>> Start-up - Adjusting cutting height <<
Lift tractor at rear and push off pallet.
Dispose of pallet and packing materials properly.
Secure the tractor from rolling away with the wheel locks!
10
GB 10
Page 11
ASSEMBLY
The following assembly work must be carried out before the first
operation:
1. Installation of the wheels.
2. Installation of the steering wheel.
3. Installation of the driver's seat.
4. Assembly of the grass box
5. Fitting the grass box to the lawn tractor.
Attention!
Putting into operation (even test operation) before complete
assembly has taken place is strictly forbidden - dangers of
accidents!
The information on directions (right, left, top etc.) for this appliance
are to be understood in the direction of travel looking from the
driver's seat.
The order of assembly steps is to be complied with, as otherwise
flawless function cannot be guaranteed.
Please note:
The figures stated to the left of the text, such as the
here, refer to the illustrations in the illustrated part at the front.
Front wheels:
Rear wheels:
10
11
12
Lock both front wheels.
Lift tractor slightly by bumper and pull to front wheel.
6
7
8
9
Push washer toward wheel rim.
Insert lock washer into shaft groove before washer and
press down.
2x lock washer dia. 15x29x1.5 - contained in screw/bolt bag.
Fit cover cap.
Lock both rear wheels.
Move tractor to rear wheel until rear wheel is heard to strike
steering knuckle.
Wheel axle protrudes from rim.
O-ring Ø11 x 2.6 is fitted in the works –
(secures the parallel key).
10
GB
13
14
15
16
Remove O-ring - do not re-use
Fit one washer
1x 19 mm dia. x 26 mm dia. and
1x 20 mm dia. x 42 mm dia.
each on axle - first 19 mm dia. x 26 mm dia.!
Insert lock washer in shaft groove and press down.
Fit cover cap.
Assembly of the steering wheel
Point the front wheels straight ahead in the direction of
17
movement.
Push the 8 x 60 ∅ clamping sleeve about 10 mm into the
bore of the steering wheel hub.
Put the steering wheel onto the steering column.
Ensure the correct position: the spoke is to point towards
the driver's seat.
Put the round iron (7 x 150 mm ∅) of the enclosed spark
plug connector into the free bore of the steering wheel hub.
Turn the steering wheel until the round iron can be pushed
through the bore of the steering wheel.
Connect with steering wheel with the steering column by
pushing in the 8 x 60 ∅ clamping bolt.
Installing the driver's seat
Unscrew the driver's seal according to the diagram on the
18
hinged console.
n Hexagonal recess hole screw M8 x 20 (2 x)
Fan-disk Ø 8.4 x Ø 15 (2 x)
Disk Ø 8.4 x Ø 24 (2 x)
Spacer bushing Ø 8.2 x Ø 14 (2 x)
o Hexagonal recess hole screw /
Wing screw M8 x 20 (2 x)
Fan-disk Ø 8.4 x Ø 15 (2 x)
Push the seat into the required position and tighten the
screws by means of the enclosed socket wrench – 6 mm
(Allen key)!
The seat can be moved in a longitudinal direction by
loosening the screw
o.
GB 11
Page 12
Assembling the grass box
19
20
21
22
23
24
25
Place the lower part of the frame on a suitable base (e.g. a
table).
Screw the upper part of the frame onto the lower part of the
frame on both sides.
M 6 x 35 hexagonal head screw (4 x)
Ø 6 x Ø 18 shim (4 x)
Ø 6 x Ø 12 shim (4 x)
M 6 self-locking nut (4 x)
Attention!
Only tighten the nuts by hand to start with due to the
subsequent fixing of the box fabric.
Fit shim Ø 6 x Ø 18 under the screw head!
Screw the transverse tube
M 6 x 45 hexagonal head screw (2 x)
Ø 6 x Ø 12 shim (4 x)
Ø 6 curved shim (2 x)
M 6 self-locking nut (2 x)
Place the frame onto the box base of the fabric sack.
Attention:
The ribs of the box base pointing upwards.
Clip the fabric sack onto the box frame.
Remove the upper frame screw connection and screw the
fitting flap of the fabric sack together with the upper and
lower part of the box frame.
Fit the Ø 6 x Ø 18 shim under the screw head.
Carry out this procedure on both sides.
Clip the stopper
side of the box lid.
Screw the contact elbow
box lid.
Ø 6 x 25 counter-sunk screw (2 x)
Attention!
Make sure that the position of the contact elbow is as
shown.
Screw the box handle
and "superstructure right"
M 8 x 60 screw (2 x)
Ø 8 x Ø 15 shim (2 x)
shim (2 x)
Attention!
The connection contours of the two superstructures
must correspond with the outer contour of the box lid.
n into the opening on the right-hand
o onto the box frame.
o for the box switch onto the
n onto "superstructure left" o
p.
GB
Screw the box handle onto the box lid
26
27
28
29
M 6 x 20 screw (2 x)
Ø 6 x Ø 12 shim (2 x)
Ø 6 x Ø 18 shim (2 x)
M 6 self-locking nut (2 x)
Position the box lid and screw onto the box frame
M 6 x 40 hexagonal head screw (5 x)
Ø 6 x Ø 18 shim (5 x)
Ø 6 x Ø 12 shim (5 x)
M 6 self-locking nut (5 x)
Holder (2 x)
Attention!
Fit the Ø 6 x 18 shim under the screw head.
Push the box strut (Ø 8 mm) through the base of the
box and the lower part of the frame.
Attention!
The box strut must protrude by the same distance on
both sides of the box.
Thread the gas spring onto the box strut in the order
shown and screw tight. Carry out this procedure on
both sides.
n Ø 12 x 13 spacer bushing (2 x)
o Gas-pressure spring (2 x)
p Ø 8 x Ø 15 shim (2 x)
q M 8 self-locking cap nut (2 x)
Attention!
Only tighten the cap nuts to such an extent that the gaspressure springs can still be pivoted
Assembling the grass box on the tractor
Hold the grass box by the box handle in one hand. With the
30
31
32
other hand - gently pressing onto the box lid - position the
upper part of the frame onto the box holding arms and push
forwards until the grass box engages in the bearings.
Attention!
The arrows on the box lid and the seat console must
match.
If the gap between the box lid and the seat console is too
large, the box holding arms can be adjusted by loosening
the screws in the directions shown
Push the forkhead
fitting lug
Push the securing bolts
and lock them.
Carry out this procedure on both sides.
o of the back wall until the bores are flush.
n of the gas-pressure spring across the
p through the forkhead and the lug
GB 12
Page 13
GB
FIRST OPERATION
The lawn tractor may only be put into operation when
the assembly has been completed.
Safety systems
The lawn tractor is fitted with 3 safety contacts which are operated
by
a) the driver's seat
b) the grass box and
c) the pedal.
The engine can only be started if
the driver is sitting on the driver's seat, the brake has been
operated and the mowing appliance has been switched off.
The engine is automatically switched off if
a) the driver gets off without operating the brake
b) the driver gets off with the mowing appliance still running
c) the grass box is opened or removed with the mowing appliance
still running.
33
34
Tyre pressure
Check the tyre pressure at regular intervals.
Examine the precise air pressure on the tyre.
1 PSI = 0.07 bar
The tyre pressure can be checked without any difficulties by using a
standard foot-pump.
Filling with engine oil and fuel.
Opening the bonnet:
1. Put your hands into the ventilation slots of the bonnet.
2. Gently pull the bonnet in the direction of the steering
wheel and lift it up until it makes contact with the
bumper.
Pour engine oil in before the first operation
– see operating instructions of the engine manufacturer.
Regularly check the oil level.
Fuel: standard petrol - lead-free.
TAKE CARE WHEN POURING FUEL IN
Only fill the petrol tank in the open. Do not smoke. Do not
pour in petrol when the engine is running or hot.
Use a suitable funnel attachment or feeder funnel to pour
in petrol so that no fuel can be spilt on to engine, the
housing or on the lawn. If petrol is spilt, do not start the
engine. Remove the mower from the area contaminated
with petrol. The spilt petrol must be sucked or wiped off the
engine and the housing with a cloth.
No attempts at ignition may be made until the vapours
have disappeared.
Starter battery
As a matter of principle, the starter battery is charged ex works. Should
starting problems nevertheless occur, the battery must be charged
before the first operation of the lawn tractor.
During the operation, the starter battery is charged by the engine. Under
normal conditions, re-charging will only be necessary after longer
periods without use (longer than 3 months).
Charging the starter battery: see "Maintenance and Service".
We recommend charging this maintenance-free and gas-tight
battery with a charging device specifically suited for this (can be
purchased from specialist dealers).
If a different charging device is used, the charging current may not
exceed 5 A and the charging voltage 14.4 V. If there is a higher
charging voltage, there is a danger of the starter battery exploding.
The starter battery is recyclable.
Used and defective starter batteries must not be disposed of via
domestic refuse. Your dealer, the manufacturer of the device or the local
battery collection points (pay attention to the local directives) will assure
proper disposal of these batteries.
OPERATING ELEMENTS
35
n Gas lever
The engine speed is regulated with the gas lever. In order
to mow as effectively as possible, the gas lever should be
switched to .
o Light switch
Use the light switch to switch the headlights on.
p Ignition lock
To start the engine, put the ignition key into the ignition lock
and turn to the right to position "II".
As soon as the engine is running, let go of the ignition key
(ignition key returns to position "I").
To switch the engine off, put the gas lever onto , then
turn the ignition key onto position "0".
Mowing appliance switch
40
The mowing appliance is operated with this toggle switch.
Switch position I - mowing appliance switched on
Switch position 0 - mowing appliance switched off
GB 13
Page 14
36
36
37
39
40
Meaning of the symbols on the
pedal
Clutch
Brake
"Clutch / Brake" pedal
n If the pedal is half pushed down, the clutch is
disengaged. If the pedal is completely pushed
down, the clutch is disengaged and the disk brake
of the transmission operated.
o With the pedal completely pressed down, the
pedal can be locked in the "Brake" function by
pushing the stop lever to the left (with the heel of
the shoe).
Pushing the pedal down again cancels the locking - the
stop lever returns to the original position.
Switching lever (for hydrostat drive)
Possible transmission positions:
Forward gear - infinitely adjustable
Reverse gear - infinitely adjustable.
and a neutral position.
Switching lever
(for 5-gear transmission)
With the switching lever,
5 forward gears
1 reverse gear and
1 neutral position can be switched.
Position lever for adjustment of
cutting height
The mowing appliance is lifted or lowered with the position
lever.
Six positions are available. In order to get from a higher to
a lower position, the push button on the end of the lever
must be pushed to unlock it.
In order to reach a higher position, simply push the lever
upwards into the required position
GB
START OF OPERATION
Starting the engine
IMPORTANT!
Check the oil level before each start of operation.
Engine exhaust fumes contain carbon monoxide, a non-odorous
and lethal gas!
For this reason, never start the engine in enclosed or badly
ventilated rooms.
• Sit down on the driver's seat.
• Push the right-hand pedal (clutch/brake) right down
- possibly engage with the stop lever.
The mowing appliance must not be switched on.
• For a cold start, put the throttle lever onto CHOKE .
• Starting the engine with a "HONDA engine"
During the starting procedure, hold the throttle lever in the
CHOKE position.
If you let go of the throttle lever, it automatically returns to the
FAST position.
• If the engine is warm, put the throttle lever onto FAST .
• Put the ignition key into the ignition lock.
• Turn the ignition key to the right to position "II" (Start).
• When the engine is running, let go of the ignition key.
(The ignition key automatically returns to position "I").
• An attempt at starting should only last for about 5 seconds so that
the starter battery is not strained unnecessarily.
• As soon as the engine is running, put the throttle lever into a
position between and .
• The engine should warm up for a few minutes before the mowing
appliance is switched on.
Stopping the engine
• Switch off the mowing appliance.
• Put the gas lever onto .
• Briefly press the brake pedal down - if necessary, engage the
brake pedal.
• Turn the ignition key to the left to position "0".
• If the lawn tractor is left unused or unattended, remove the ignition
key and engage the brake pedal.
Driving with the lawn tractor
• Start the engine.
• When the engine is running, select the corresponding forward or
reverse gear. With a hydrostat drive, pre-select the corresponding
position in forward or reverse drive.
For the first use of the lawn tractor, we would advise that you only
choose 1
• To start motion, slowly release the clutch/brake pedal.
IMPORTANT!
Do not switch the 5-gear transmission while driving.
The lawn tractor must be stationary in order to change gear.
st
gear or set the hydrostat drive to MIN.
GB 14
Page 15
Brakes
• Press the right-hand pedal
down completely in order to brake.
Switching the mowing appliance on
• Only switch the mowing appliance on with the engine running.
• Put the gas lever into the position.
• Set the required cutting height.
• Put the mowing appliance switch onto position
IMPORTANT!
When you switch the mowing appliance on, the mower should not
be standing in long grass. Set to the highest cutting height.
"I".
Switching the mowing appliance off
• Put the mowing appliance switch onto position "0".
• The mowing appliance can be switched off both at a standstill and
also during movement.
IMPORTANT!
A rotating / slowing blade can cut hands and feet.
Therefore, keep your hands and feet away from the blades.
Setting the cutting height
The blades are raised and lowered with the position
40
lever to the right of the driver's seat.
Six height settings with a cutting height between 30 and
90 mm are possible.
Allow the position lever to engage at the height
adjustment position required.
Adjustment of the cutting height can be done both at a
standstill and also during movement.
IMPORTANT:
Set the highest cutting height:
- before switching the cutting appliance on
- when driving without mowing
GB
Driving without traction (pushing)
41
IMPORTANT!
Only with the engine switched off and the blades
stationary!
a) For a 5-gear transmission:
1. Put the switch lever into position 0.
2. Release the brake.
b) For a hydrostat drive:
1. Remove or lift up the grass box.
2. Pull out bypass lever
3. Release the brake.
The lawn tractor can now be pushed without any difficulty.
n and engage downwards o.
Driving and mowing
In order to achieve a tidy mowing result, the traction speed must be
adapted to the state of the lawn.
38
39
In a normal case, the cutting height is about 4-5 cm. This corresponds to
the 2
a higher cutting height.
The best thing to do with very long grass is to cut it twice. For the first
cut, set the machine to max. cutting height and set it to the required
height for the second cut.
a) Lever position for hydrostat drive:
– long / thick grass and wet grass: 0 - ¼
– normal grass, weekly cutting: ½ - 2/3
The lever positions from 2/3 - 1/1 are reserved for driving
without mowing.
b) Lever position for 5-gear transmission:
– long / thick grass and wet grass: 1
– normal grass, weekly cutting: 2
th
4
and 5th gear are reserved for driving without mowing.
nd/3rd
position of the height adjustment. Cut moist or wet grass with
st
gear
nd
- 3rd gear
Driving on slopes
Special care is needed when driving on slopes.
Please observe the following information:
– Do not drive on slopes with an inclination of more than 10°
(18%).
– Do not jolt when starting.
– Keep the speed low.
– Do not stop or accelerate strongly.
– Do not declutch when going down the slope.
GB 15
Page 16
Emptying the grass box
The grass box can be emptied from the driver's seat.
IMPORTANT!
When the grass box is full, an acoustic signal can be heard. The
box should be emptied now at the latest.
Switch the mowing appliance off - acoustic signal goes off.
42
Empty the grass box:
n Press the box locking button.
o Push the box locking button backwards until it
engages.
p Pull the grass box upwards by hand.
Shake the grass box a number of times in order to empty it
completely.
If the grass box is lifted or removed with the mowing
appliance still switched on, the motor cuts out.
Closing the grass box:
1. Press the box locking button.
2. Push the box locking button forwards until it goes
up again.
3. Push the grass box down by hand until it engages
in the lowest locking position.
IMPORTANT!
If the grass box is not positioned properly, the mowing
appliance cannot be switched on.
CARE AND MAINTENANCE
Cleaning the lawn tractor
In order to work properly, the lawn tractor must be cleaned regularly.
After each use, clean adhering residue from the lawn tractor and the
grass box.
GB
Grass box
Take the grass box off the lawn tractor.
The gas springs must be removed before you can take the
28
grass box off the lawn tractor.
Clean the fabric sack from the outside with a jet of water.
If necessary, also clean the inside of the fabric sack with a
brush.
Housing / engine / transmission
The engine and all the bearings (wheels, transmission, blade bearings
etc.) must not be cleaned with water, in particular not with a highpressure cleaner.
Any water penetrating into the ignition unit, into the carburettor and the
air filter can cause damage. Water in the bearings can lead to a loss of
lubrication and thus to the destruction of the bearings.
To remove dirt and residue of grass, use a cloth, a hand-held
sweeper, a long-handled brush etc.
Electrical unit
Do not clean the electrical unit with water. Penetration of
water into the electrical unit (switch, display, cable,
operating elements etc.) can lead to damage.
Discharge channel
The ease of movement of the adjustment of the cutting
43
height is guaranteed by regular cleaning.
The discharge channel comprises two parts pushed into
one another.
The lower part is firmly attached to the mower housing.
The upper part can be removed for cleaning.
The grass box must be taken off before you can remove the
discharge channel.
Remove screw connection n on the left and right of the
discharge channel.
IMPORTANT!
There is a shim under each screw.
Pull discharge channel o out backwards through the rear
wall. Thoroughly clean the upper and the lower discharge
channel.
The discharge channel is put back in reverse order.
Replacing and resharpening the mowing
blade
At the end of the mowing season always resharpen the mowing blade or,
if required, replace the mowing blade with a new one.
Always have the mowing blade resharpened or replaced by a customer
service centre (measurement of imbalance).
Unbalanced blades will cause the lawn mower to vibrate violently –
risk of accident!
GB 16
Page 17
44
Mowing system
On the mowing deck, there are two connections for a ½"
water hose coupling.
The mowing system can be cleaned by connecting a water
hose.
During the cleaning process, the grass box or a
suitable accessory must be fitted.
1. Lower the mowing deck to the lowest cutting height.
2. Start the engine - set a medium engine speed.
3. Switch the mowing appliance on.
4. Connect the hose alternately to the connections and
turn the water on.
After a few minutes, the mowing system has been
cleaned.
5. Leave the mowing system to run for a few more minutes
in order to spin the water out.
6. Clean the grass box and leave to dry.
MAINTENANCE AND SERVICE
GB
Checking by a qualified service agent is
necessary:
– after impact with an obstacle
– if the V-belt is defective
– if the engine comes to an immediate standstill
– if the brake performance drops
– if the blade is bent (do not straighten)
– if the drive belt slips
– if the blade shaft is bent (do not straighten)
– if there is a defect in the blade holder
– if there is damage to the transmission.
Check level of engine oil
Change engine oil
Clean the air filter
Replace the air filter
Check the spark plug
Check the brake
Check the tyre pressure
Check mowing blade
Maintenance, service and cleaning work may only be carried out when the machine has been turned off and has cooled down
and the ignition key has been removed.
The following tasks may be carried out by the user himself. All the other maintenance, service and upkeep tasks must be
carried out by a qualified service agent.
Before each
use
After each
use
After the
first 5 hours
After 25
hours of
operation
After 50
hours of
operation
Before each
storage
Check for loose parts
Check drive belt
Clean the lawn tractor
Clean air intake grille on engine
Clean grass and cuttings from transmission
For hydrostat drive:
Clean ventilator for transmission cooling
In cases of high load and high temperatures, shorter maintenance intervals than those stated in the table may be necessary.
)* see operating instructions of the engine manufacturer
GB 17
Page 18
Lubrication plan
In order to ensure the ease of movement of the moving parts, we
recommend lubricating the following parts after 10 hours of
operation.
Front axle:
Steering swivel right and left (lubrication nipple):
- with multi-purpose grease
Bearing of the front axle on the frame
- with spray oil
Steering:
Gear segment and steering pinion on steering gear
- with multi-purpose grease
Front / rear wheels:
roller bearings and hub
- with multi-purpose grease
For lubrication of the axles, the front and rear wheels must be
dismantled (see Change of Wheels).
Pivots and bearings:
Lubrication of all moving pivot and bearing points,
as well as the cable pulls:
- with spray oil.
Oil change
See operating instructions of the engine manufacturer.
The oil change can be done by sucking the oil out via the oil filling
opening (a corresponding suction device can be purchased from your
dealer).
IMPORTANT!
Dispose of used oil in accordance with statutory directives. Do not
discharge used oil into the sewers or the ground. Contamination of
groundwater is severely punished. Or your local authority can tell
you where to dispose of it.
Air filter and spark plug
See the operating instructions of the engine manufacturer.
Transmission / hydro-transmission
The transmission needs no maintenance as it has been given a life-time
filling of oil in the factory.
GB
Wheel change
A wheel change may only be done on a level and firm base.
45
1. Park the lawn tractor with the parking brake and secure
it against rolling away with wedges.
2. Lift the lawn tractor on the side of the wheel to be chan
ged and place a suitable object (e.g. a block of wood)
under a supporting element of the chassis.
3. Push the circlip off with a screwdriver and remo ve
the spacer shim.
4. Pull the wheel off the axle.
IMPORTANT!
Do not lose the adjusting spring when pulling the rear
wheels off the axle.
When putting back together, grease the axles with
customary multi-purpose grease.
STARTER BATTERY
The starter battery can be found underneath the bonnet.
As a matter of principle, the battery has been charged in the factory.
Further charging is necessary:
a) before storage for the winter break
b) if the machine is not used for a long time (longer than 3 months).
IMPORTANT!
We recommend charging this maintenance-free and gas-tight
starter battery with a charging device specifically suited for this
(can be purchased from specialist dealers).
IMPORTANT!
The charging current of the charging device may not exceed 5 A
and the charging voltage 14.4 V. If there is a higher charging
voltage, there is a danger of the starter battery exploding.
Check tyre pressure
Check the tyre pressure at regular intervals.
Examine the precise air pressure on the tyre.
1 PSI = 0.07 bar
The tyre pressure can be checked without any difficulties by using a
standard foot-pump.
GB 18
Page 19
Charging the starter battery
IMPORTANT!
The starter battery may only be charged in dry rooms.
1. Remove the ignition key.
2. Connect the charging device to the mains and connect the termi
nals to the connection poles on the battery.
Pay attention to the polarity:
red terminal = positive pole (+)
black terminal = negative pole (-)
Function of the charging device: see operating instructions for charging
device.
Maintenance for the starter battery.
When storing for the winter, keep the starter battery in a cool, dry room
(10 - 15°C).
Temperatures below freezing should be avoided during storage.
Do not leave discharged batteries uncharged for a long time.
Use a suitable charging device to charge the starter battery.
The starter battery must not:
• be stored in the immediate vicinity of naked flames
• be burnt
• or put onto radiators.
DANGER OF EXPLOSION.
Do not destroy the starter battery. The electrolyte (sulphuric acid) causes
acid burns to the skin and clothes - wash off with plenty of water straight
away.
Do not short circuit the connection poles.
Keep the starter battery clean. Only wipe with a dry cloth. Do not use any
water, petrol, thinners or similar agents.
Keep the connection poles clean and grease them with pole grease.
GB
Storage in winter
After the end of the mowing season, clean the device thoroughly.
Do not clean the engine with water, in particular not with a high-pressure
cleaner.
Any water penetrating into the ignition unit, into the carburettor and the
air filter can cause damage.
To remove dirt and residue of grass, use a cloth, a hand-held sweeper, a
long-handled brush etc.
Empty the fuel tank.
Change the oil and preserve the engine - see operating instructions of
the engine manufacturer.
Completely charge the battery.
Keep the machine in a dry, frost-free room. If there is a danger of frost,
remove the starter battery and store it in a frost-free area.
If the starter battery remains in the machine for a longer period (longer
than 1 month), remove the earth cable from the battery.
Recharge the battery after it has stood for longer than 3 months.
An inspection of the lawnmower in the winter is a benefit.
Transport of the lawn tractor
IMPORTANT!
When transporting the lawn tractor with transport equipment (e.g. a
car trailer), support the mowing deck in order to relieve the Bowden
cables.
Storing the lawn tractor
IMPORTANT!
The machine is to be protected against the influences of the
weather, in particular moisture, rain and long periods of direct
sunshine.
GB 19
Page 20
GB
TROUBLE SHOOTING
FAULT POSSIBLE CAUSES REMEDY
Engine does not start
Starter does not react
Engine performance drops
Lawn tractor does not move
Poor cut
Grass box not filling
Level display does not react
Drive, brakes, clutch and
mowing appliance
Lack of fuel Fill the tank, check the tank venting, check the fuel filter
Bad, contaminated fuel, old fuel in the tank Always use fresh fuel from clean containers, clean the
Air filter contaminated Clean the air filter (see operating instructions for the engine)
No ignition spark Clean the spark plug, possibly replace. Check ignition
Engine "flooded" due to repeated attempts to start Unscrew spark plug and dry off.
Starter battery empty or weak Charge starter battery
Safety switch on driver's seat not functioning Sit on the driver's seat correctly
Safety switch on brake pedal not functioning Press the brake pedal right down
Mowing appliance switched on Switch the mowing appliance off
Fuse (5A) on (+) cable of the starter battery Check
Grass too long or too wet Correct the cutting height. Create air flow by briefly moving
Discharge channel/mowing deck blocked Clean discharge channel/mowing deck. Switch the engine
Air filter contaminated Clean the air filter (see engine information)
Carburettor setting wrong Have the setting checked - authorised service agent
Blade severely worn Replace blade - Only use original replacement blade -
Speed too high Reduce speed
With hydrostat drive:
No traction
Blade worn, blunt Replace or regrind blade. Balance reground blades. Only
Incorrect cutting height Alter cutting height
Engine speed too low Set engine speed to Max.
Speed too high Reduce speed
Differing tyre pressure on wheels Pump up to correct air pressure.
Mower setting too low; Adjust cutting height
Grass is too damp and too heavy to be transported
by the air flow
Blade badly worn Replace blade. Only use original replacement blade -
Grass too long Cut the lawn twice:
Fabric sack blocked - no air flow Clean the fabric sack
Discharge channel of mowing deck blocked - last
cuttings
Cuttings on level display lever Remove cuttings from level display lever - check for each of
have a regular check done by the authorised service agent.
GB 20
carburettor (workshop)
cable. Check ignition unit = authorised service agent
backwards
off and remove the spark plug connector.
authorised service agent
Move bypass lever downwards to operating position (see
driving without traction)
use original replacement blade - authorised service agent
Tyre pressure: see technical data
Wait until the lawn has dried off
authorised service agent
st
cut: max. cutting height
1
nd
2
cut: required cutting height
Clean the discharge channel/mowing deck
movement
Page 21
GB
WARRANTY
LIMITED WARRANTY
Hayter Limited warrants to the original user / purchaser that this unit shall be free from defects in material and
workmanship under normal use and service for a period of three years from the date of purchase. The manufacturers of the
engine and battery pack system (where applicable) fumish their own warranty and services are provided through their
authorised network (Refer to "Engine/Battery Pack Warranty Statement'). To qualify for the full benefit of the warranty, the
warranty registration card must be returned within 60 days of purchase. Subject to the conditions and exclusions noted in
this limited warranty, we shall at our Option, repair or replace any warranted part during the applicable period. If you are in
doubt or experience any difficulty, please consult a Hayter Authorised Service Dealer for clarification.
To qualify for the extended warranty (second and third year) of the three year limited warranty, the machine must haue
annual services carried out by an Authorised Hayter Service Dealer. These chargeable services should be carried out within
12 and 24 months of the date of purchase.
Excluded from the extended warranty period are those items which are subject to normal wear and tear e.g. tyres, wheels,
cutterbars, Gables, batteries and other consumable wearing parts.
All consumer machines which are fitted with a genuine Hayter friction disc as original equipment, before use, are covered
by a Lifetime Warranty against the engine crankshaft bending. Note: friction washers, blade brake units and other such
devices are not applicable. Only machines fitted with a genuine Hayter friction disc, which are used in accordance with the
recommended operating and maintenance procedures, are covered.
This warranty does not apply to any unit that has been tampered with, altered, misused, abused or used for hire, and will
become invalid if non genuine Hayter parts are fitted. This warranty does not cover minor mechanical adjustments unless
they are due to defective materials or workmanship. Consult the Owner's Handbook or a Hayter Authorised Service Dealer
for assistance when making these adjustments.
A warranty period of 90 days applies to machines used for commercial purposes.
To make a warranty Claim, retum the unit to a Hayter authorised dealer along with proof of purchase stating the machine
serial number and date of purchase. The service receipt(s) or this Owner's Handbook with the 1st/2nd year service boxes
fully completed, must be produced as proof of entitlement to the extended warranty period. Subject to the conditions and
exclusions in this limited warranty, the authorised dealer will, at our Option, repair or replace any warranted part within the
duration of the warranty period.
This limited warranty gives you specific legal rights and is in addition to any statutory rights to which you may be entitled and
your statutory rights are not affected by this warranty. If you need additional Information concerning this written warranty, or
assistance in obtaining services, please write to:
HAYTER LIMITED, Service Department, Spellbrook, Bishop's Stortford, Hertfordshire. CM23 4BU.
UK ONLY: Details of your local Hayter authorised dealer are contained in Yellow Pages or contact: Freephone 0800 616298.
1st 2nd
Year Year
Service Service
Record Record
Date………………………………………………………….. Date…………………………………………………………….
Signed……………………………………………………….. Signed………………………………………………………….
GB 21
DEALER STAMP DEALER STAMP
Page 22
GB
DECLARATION OF CONFORMITY
EC DECLARATION OF CONFORMITY
Manufactured by
AL-KO Kober GmbH, A-8742 Obdach
AUSTRIA
Certify that the lawntractor:
Model: Heritage RS 17/102H
Machine Type: Code 149D
W idth of cutting device: 1020 mm
Motortyp: B & S Intek OHV AVS
Speed of rotation of cutting device: 2900 rpm
Measwed sound power level: 99 dB(A)
Guaranteed maximum sound power level: 100 dB(A)
NOISE TESTED AT - TÜV Süddeutschland Bau und Betrieb GmbH, Westendstraße 191, D – 80686 München
Date Tested: 14/08/01
We declare that the machine lawntractors, conforms to the specifications of the following EC directives:
98/37/EC Essential Health & Safety Requintments Relating to the Design & Construction of Machinery and Safety Components.
2000/14/EC Noise emission in the environment by equipment for use outdoors. 89/336/EEC amended by 92/31/EEC
Electromagnetic Compatibility. 2002/88/EC
Standards Used: EN292, EN836 and ENIS014982
Signed Date: 20/02/02
Ing. Rainer Klaus
(Director)
VIBRATION INFORMATION
Lawntractor vibration information. RMS acceleration measured in 3 - axes at operators contact position an,
the handlebars.
CODE 149D = 4,2 ms²
GB 22
Loading...