Haws 9102 User Manual

C

UCTIONS

INSTALLATION, OPERATION

&

MAINTENAN

1455 Kleppe Lane Sparks, NV 89431-6467 [phone] Fax [phone]

HAWS AG Bachweg 3 CH-3401 Burgdorf  Switzerland

Haws Mfg. Pte Lt. 2A Sungei Kadet Drive Singapore 729554

Avlis-Avenido Senador, Testonio Vilela 505 Jardim Aeroporto  Itu, S.P. 13304-550 Brasil

E-mail: [e-mail]

NOTE TO INSTALLER: Please leave this information with the Maintenance Department.

HAWS® warrants that all of its products are guaranteed against defective material or poor
workmanship for a period of one year from date of shipment. HAWS liability under this
warranty shall be discharged by furnishing without charge F.O.B. HAWS Factory any
goods, or part thereof, which shall appear to the Company upon inspection to be of
defective material or not of first class workmanship, provided that claim is made in writing
to company within a reasonable period after receipt of the product. Where claims for
defects are made, the defective part or parts shall be delivered to the Company, prepaid,
for inspection. HAWS will not be liable for the cost of repairs, alterations or replacements,
or for any expense connected therewith made by the owner or his agents, except upon
written authority from HAWS, Sparks, Nevada. HAWS will not be liable for any damages
caused by defective materials or poor workmanship, except for replacements, as provided
above. Buyer agrees that Haws has made no other warranties either expressed or implied
in addition to those above stated, except that of title with respect to any of the products or
equipment sold hereunder and that HAWS shall not be liable for general, special, or
consequential damages claimed to arise under the contract of sale.

The emergency equipment manufactured by HAWS is warranted to function if installation
and maintenance instructions provided are adhered to. The units also must be used for
the purpose, which they were intended. This product is intended to supplement first-aid
treatment. Due to widely varying conditions HAWS cannot guarantee that the use of this
emergency equipment will prevent serious injury or the aggravation of existing or prior
injuries.

NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED,
PROVIDED OR GIVEN BY HAWS.

SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL, PLEASE CALL:

FOR PARTS CALL:

Model 9102 Stainless Steel Dust Cover

LIMITED WARRANTY

1-800-766-5612

1-800-758-9378

(U.S.A. AND CANADA ONLY) MONDAY-THURSDAY: 6:00 A.M. – 4:00 P.M. PST

FRIDAY: 6:00 A.M – 1:00 P.M. PST

 website: www.hawsco.com

E INSTR

No. 2080227(3)

01/07 Model 9102 Page 1 of 3

INSTALLATION PROCEDURE

Refer to the attached drawing to clarify installation.

STEP 1: Remove the nut that holds the eyewash push flag to the valve stem. If the unit is

also foot operated, remove the ring from the end hole of the flag.

STEP 2:

STEP 3: Put the flag on the valve stem before attaching the link on it through the first hole

STEP 4: Align the second holes on the flag and the link. Insert the 3/8” – 24 UNC x 1”

STEP 5: If the eyewash is foot operated, reattach the ring connected to the chain into the

STEP 6: After making sure that the cover and the receptor are properly positioned, tighten

STEP 7: Test the eyewash to ensure the full access and the sufficient water flow while

Before performing any troubleshooting work, inform all related parties of the discontinuation of
service. Service to be performed on equipment by qualified personnel.

© 2006 Haws
HAWS

Position the dust cover assembly over the existing ∅11” eyewash receptor. After

checking for the initial alignment, tighten the adjustable strap around the receptor
only enough to keep it from sliding during the installation process.

on the link. Secure the flag and the link to the valve stem by tightening the
shoulder nut provided.

screw (with hole) through the holes and tighten it with the nut. Use some
lubricant if necessary.

hole of the 3/8” – 24 UNC x 1” screw.

the adjustable strap firmly to secure the dust cover assembly on the eyewash
unit.

open.

TROUBLESHOOTING

PROBLEM

1. Cover does not open all the way.

b. If the unit is also foot operated, check the

2. Cover is not aligned with the receptor. 2. a. Loosen the strap then adjust the link and

®

®

Corporation – All Rights Reserved

and other trademarks used in these materials are the exclusive property of Haws Corporation.

1. a. Check for obstructions behind the unit.

REPAIR CHECKLIST

chain length and adjust it if necessary.

the back mounting bracket.

01/07 Model 9102 Page 2 of 3