Haws 8317CTFP Installation Manual

Page 1

THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.

3/4" NPT JUNCTION BOX

DRENCH HOSE ACTIVATION VALVE ASSEMBLY

MOUNTING LOCATION FOR OPTIONAL AREA LIGHT

43 1/4"

1098mm

36-1/2"

927mm

POWER CONNECTION

6 3/4" 171mm

MOUNTING LOCATION FOR OPTIONAL INDICA TOR L IG HT

1-1/4" IPS SUPPLY UNION (INLET) TOP SUPPLY SHOWN. SEE STEP 2 OF THE INSTALLATION PROCEDURE IN THE OPERATION & MAINTENANCE MANUAL (PAGE 2) TO CONVERT TO A BOTTOM SUPPLY UNIT.

20-1/2" 521mm

IMPORTANT

SUPPLY MUST BE HEAT

TRACED AND INSULATED

1 of 4

PAGE

85-1/2" 2172mm

95-1/2" 2426mm

90-1/2" 2299mm

67-1/4"

1708mm

DRENCH HOSE

41-3/4"

1060mm

FLOOR LINE

152mm

NOTES:

1. DIMENSIONS MAY VARY BY ± 1/2 INCH [13mm].

2. TO COMPLY WITH ANSI Z358.1-2009 FOR EMERGENCY EYEWASH OR EYE/FACE WASH AND SHOWER EQUIPMENT:

- UNIT SHALL BE INSTALLED IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS AND ACCEPTABLE PLUMBING PRACTICES.

- EYEWASH OR EYE/FACE WASH SHALL BE POSITIONED WITH NOZZLES NOT LESS THEN 83.8 CM (33 IN.) AND NO GREATER THAN

114.3 CM (45 IN.) FROM SURFACE ON WHICH USER STANDS AND 15.3 CM (6 IN.) MINIMUM FROM WALL OR NEAREST OBSTRUCTION.

- SHOWER SHALL BE POSITIONED SO THAT SHOWER HEAD IS NOT LESS THAN 208.3 CM (82 IN.) NOR MORE THAN 243.8 CM (96 IN.) FROM SURFACE ON WHICH USER STANDS.

- SHOWER SPRAY PATTERN SHALL HAVE A MINIMUM DIAMETER OF 50.8 CM (20 IN.) AT 152.4 CM (60 IN.) ABOVE SURFACE ON WHICH USER STANDS, AND CENTER OF SPRAY PATTERN SHALL BE LOCATED AT LEAST 40.6 CM (16 IN.) FROM ANY OBSTRUCTION.

3. DO NOT USE REGULAR PIPE SEALANT. IF NECESSARY USE DOW CORNING 832 SEALANT PLACING 5 SMALL BEADS ON THE MALE THREADS, JUST ABOVE THE FIRST THREAD.

(NOTES CONTINUED ON SHEET 2 OF 4.)

2014

HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.

REMOVABLE ABS JACKET

178mm

DRAWN:

RTM

APPROVED:

REVISE D PER

ECN:

4921

DATE:

03/29/05

DATE:

BY:ECN NO. CHK'D.:

10/21/14

14"

355mm

MODEL(S)

SCALE:

30°

NOTE: PULL ROD AND HANDLE NOT ASSEMBLED. ORIENTATION OF HANDLE

6-3/4" 171mm

MUST BE IN UP POSITION WHEN FULLY CLOSED AND PULL ROD INSERTED IN HOLE SHOWN.

SP158B FREEZE PROTECTION VALVE (SEE NOTES ON SHEETS 2 & 3 FOR INSTALLATION INSTRUCTIONS.)

(775) 359- 4712 FAX (755) 359-74 24

E-MAIL: [email protected] WEBSITE: WWW.HAWSCO.COM

8317CTFP(120V)/ 8317CTFP.220V

DRAWING TYPE: SIZE: A

1/20

INSTALLATION

Ø9"

Ø229mm

Ø8"

Ø203mm

1455 KLEPPE LANE

SPARKS, NEVADA 89431

PART NUMB ER

0002081781.D

DRAWING NO.

15201A00

SHEET OF

Ø3/8"

Ø10mm

B.C.

REV

Page 2

THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS MAKE SPECIFICATIONS AND MEASU REM ENTS SUBJECT TO CHANGE WITHOUT NOTICE.

NOTES: (CONTINUED FROM SHEET 1 OF 4)

. FREEZE PROTECTION VALVE INSTALLATION INSTRUCTIONS: INSTALL VALVE SUB-ASSEMBLY INTO FEMALE SECTION OF UNION AND TIGHTEN WATER-TIGHT.

FORM HEAT TRACE CABLE AROUND VALVE AND PLUG, APPLY 2X CABLE-TIES TO HEAT TRACE CABLE, AS SHOWN, ENSURING

B THAT HEAT TRACE CABLE IS PRESSED FIRMLY AGAINST SIDES OF VALVE (PUSH ANY LOOSE HEAT TRACE CABLE BACK INSIDE JACKET THROUGH RUBBER GROMMET). TRIM EXCESS CABLE-TIE STRAPPING.

SLIDE INNER TUBE W/ PLUGGED END OVER VALVE WITH ADHESIVE SEAM FACING BOTTOM AND NON-PLUGGED END OF TUBE

C BUTTED UP AGAINST UNION SURFACE. REMOVE 2X ADHESIVE TAPE FROM SEAM AND SQUEEZE ADHESIVE SEAMS TOGETHER AROUND VALVE. APPLY 2X CABLE-TIES TO TUBE, IN APPROXIMATE LOCATIONS SHOWN. TRIM EXCESS CABLE-TIE STRAPPING.

(NOTES CONTINUED ON SHEET 3 OF 4)

2 OF 4

PAGE

RUBBER GROMMET

FEMALE SECTION OF UNION (PART OF SHOWER UNIT)

MALE SECTION OF UNION (PART OF VALVE SUB-ASSY)

HEAT TRACE CABLEB

JACKET SURFACE

CABLE-TIE, 15" / PN 0005972499 B

(SEE SHEET 3.)

VALVE, FREEZE (NO UNION) SP158B

BARBED CONNECTOR

UNION SURFACE

SP158B VALVE SHOWN CONNECTED TO BOTTOM UNION FOR

REFERENCE ONLY. VALVE CAN BE INSTALLED AT TOP OR BOTTOM.

2014

Haws Corporation - All Rights Reserv ed.

HAWS and other tradem arks used in thes e m aterials are the exclusive property of Haws Corporat ion.

CABLE - TIE, 15" / PN 0005972 499

INNER TUBE W/ PLUGGED END

PLUG GED END

ADHESIVE SEAM C

BY:ECN NO .

4632

DRAWN:

VWC

APPROVED:

REVISED PER

ECN:

4921

DATE:

12/2/12

DATE:

10/21/14

CHK'D.:

MODEL(S)

SCALE:

1455 KLEPPE LANE

SPARKS, NEVADA 89431

(775) 359-4712 FAX (755) 359-7424

E-MAIL: HAWS @H AW SCO.COM WEBSITE: WWW.HAWSCO.C OM

8317CTFP (120V) / 8317CTFP.2 20V

DRAWING TYPE: SIZE: A

INSTALLATION

PART NUMBER

0002081781.D

DRAW ING NO .

15201A

SHEET OF

REV

Page 3

THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS MAKE SPECIFICATIONS AND ME ASUREMENTS SUBJECT TO CHANGE WITHOU T NOTICE.

NOTES: (CONTINUED FROM SHEE T 2 OF 4)

FREEZE PROTECTION VALVE INSTALLATION INSTRUCTIONS (CONTINUED): WRAP OUTER TUBE OVER INNER TUBE ENCAPSULATED VALVE WITH ADHESIVE SEAM ORIENTED PERPENDICULAR

D TO SEAM OF INNER TUBE. PUSH OUTER TUBE UP AGAINST JACKET SURFACE. WHEN TUBE IS MOUNTED FIRMLY AGAINST JACKET SURFACE, SQUEEZE TUBE AT BARBED CONNECTOR SUCH THAT BARBED NIPPLE PUSHES THROUGH OUTER TUBE WALL. (PUSHING CONNECTOR THROUGH WALL WILL EXTRUDE A CYLINDRICAL PLUG OF TUBING TO BREAK FREE. DISCARD PLUG.) PUSH TUBE DOWN EVEN FURTHER SO THAT HOLE IN TUBE STRETCHES AROUND HEXAGONAL BOSS OF CONNECTOR. SQUEEZE OUTER TUBE TIGHT UNTIL ADHESIVE SEAMS ARE CLOSE ENOUGH TO SEAL. REMOVE PROTECTIVE TAPE AND SEAL SEAMS.

TO ENSURE PROPER INSULATION OF UNION; THERE MUST BE NO SPACE BETWEEN OUTER TUBE AND JACKET SURFACE (SEE SHEET 2 FOR SURFACE CALLOUT). THEREFORE, SLICE TWO PLACES, TOP SIDE AND BOTTOM SIDE, COMPLETELY THROUGH OUTER TUBE TO A LENGTH EQUAL TO DEPTH OF TRIM SEAL. FORCE SLICED TUBE AROUND TRIM SEAL AND PUSH TUBE TIGHTLY AGAINST JACKET, AS SHOWN. APPLY 2X CABLE-TIE HEAD, AND 2X CABLE-TIE STRAP, TO TUBE, IN APPROXIMATE LOCATIONS SHOWN. TRIM EXCESS STRAPPING.

TRIM SEAL E

3 OF 4

PAGE

SLICED TUBE SECTION (TOP SIDE)

STRAP, 2-PC CABLE-TIE, 20" L HEAD, 2-PC CABLE-TIE / PN 0002850165

JACKET/TUBE

INTERSECTION

OUTER TUBE

INNER TUBE INSULATION SEAM

PERPENDICULAR

ADHESIVE SEA M

BARBED CONNECTOR

SLICED TUBE SECTION (BOTTOM SIDE)

SP158B VALVE SHOWN CONNECTED TO BOTTOM UNION FOR

REFERENCE ONLY. VALVE CAN BE INSTALLED AT TOP OR BOTTOM.

2014

HAWS and other tradem ar k s us ed in these materials ar e the exclusive pr oper ty of Haws Corporation.

1455 KLEPPE LANE

SPARKS, NEVADA 89431

(775) 359-4712 FAX (755) 359-7424

E-MAI L : HA W [email protected] WEBSITE: WWW.HAWSCO.COM

INSTALLATION

PART NUMBER

0002081781.D

DRAWING NO.

15201A 17

SHEET OF

REV

4632

DRAWN:

VWC

APPROVED:

REVISED PER

ECN:

4921

DATE:

12/2/12

DATE:

BY:ECN NO. CHK'D.:

10/21/14

MODEL(S)

8317CTFP(120V) / 8317CTFP. 220V

DRAWING TYP E: SIZE: A

SCALE:

Page 4

THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLIC AT IO N. CONTI NUED PRODUCT IMPROVEMENTS MAKE SPECIFICATIONS AND MEASUREMENT S SUBJECT T O CHANG E WITH OUT NOTI CE.

INDICATOR LIGHT

WIRING TO INDICATE

POWER ON

INDICATOR LIGHT

WIRING TO INDICATE THERMOSTAT ON

GROUND TO

JUNCTION BOX

TERMINAL

BLOCK

4 of 4

PAGE

GROUND

GREEN BLACK

POWER IN

120 VAC

WHITE (120V)/RED (220V)

FOR MODEL 8317CTFP

220 VAC

FOR MODEL 8317CTFP.220V

(OPTIONAL) AREA LIGHT

(8317CTFP ONLY SUPPORTS TWO OPTIONS AT A TIME)

2014

SHIELD

HEAT

TRACE

CABLE

THERMOSTAT

1455 KLEPPE LANE

SPARKS, NEVADA 89431

(775) 359- 4712 FAX (755) 359- 7424

E-MAIL: [email protected]

BY:ECN NO.

REVISED PER

ECN:

4921

DATE:

DRAWN:

RTM

03/29/05

APPROVED:

HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.

DATE:

CHK'D.:

10/21/14

MODEL(S)

SCALE:

8317CTFP(120V)/ 8317CTFP.220V

DRAWING TYPE: SIZE: A

WEBSITE: WWW.HAWSCO.COM

INSTALLATION

PART NUMBER

0002081781.D

DRAWING NO.

15201A00 17

SHEET OF

REV

44FV