Haws 9001 Alarm, 9001.5 Alarm Installation Operation & Maintenance

No. 2080202(31)

Model 9001, 9001.5 Alarm

INSTALLATION, OPERATION

&

MAINTENANCE INSTRUCTIONS

LIMITED WARRANTY

or part thereof, which shall appear to the Company upon inspection to be of defective

NOTE TO INSTALLER: Please leave this information with the Maintenance Department.

SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS

1455 Kleppe Lane Sparks, NV 89431-6467 [phone] Fax [phone]

E-mail: [e-mail]  website: www.hawsco.com

HAWS warrants that this specific product is guaranteed against defective material or poor
workmanship for a period of one year from date of shipment. HAWS liability under this
warranty shall be discharged by furnishing without charge F.O.B. HAWS Factory any goods,

material or not of first class workmanship, provided that claim is made in writing to Haws
within a reasonable period after receipt of the product. Where claims for defects are made,
the defective part or parts shall be delivered to the Company, prepaid, for inspection. HAWS
will not be liable for the cost of repairs, alterations or replacements, or for any expense
connected therewith made by the owner or his agents, except upon written authority from
HAWS, Sparks, Nevada. HAWS will not be liable for any damages caused by defective
materials or poor workmanship, except for replacements, as provided above. Buyer agrees
that Haws has made no other warranties either expressed or implied in addition to those
above stated, except that of title with respect to any of the products or equipment sold
hereunder and that HAWS shall not be liable for general, special, or consequential damages
claimed to arise under the contract of sale.

The emergency equipment manufactured by HAWS is warranted to function if installation
and maintenance instructions provided are adhered to. The units also must be used for the
purpose for which they were intended. This product is intended to supplement first-aid
treatment. Due to widely varying conditions, Haws cannot guarantee that the use of this
emergency equipment will prevent serious injury or the aggravation of existing or prior
injuries

NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED, PROVIDED OR

MODEL PLEASE CALL:

TECHNICAL SUPPORT: 1-800-766-5612

.

FOR CUSTOMER SERVICE: 1-888-640-4297

10/17 9001 Alarm Series Page 1 of 6

TROUBLESHOOTING

PROBLEM

REPAIR CHECKLIST

operate.

from flow switch.

body.

box is in the “on” position.

d.

Check for continuity through the switch.

e.

Check all electrical connections.

f.

Check that water flow is sufficient.

assembly.

flash.

b.

Replace flashing light.

sound.

the “on” position.

4.

Alarm stays on.

4.

a.

Check wiring connections.

RECOMMENDED TOOLS: Pipe joint sealant, screwdriver, pipe wrench, 14 AWG wire,
1/2"conduit and basic electricians’ tools for power connection.

LOCATION OF UNIT: The Model 9001 Alarm Series may be mounted directly to the upper
standpipe of a safety shower or wall mounted next to a shower or eyewash. The alarm should
be clearly visible from several directions.

ELECTRICAL SUPPLY:

Model 9001 & 9001.5 120 VAC 50/60 HZ.
14 watts average power consumption. WARNING: Power shall be supplied by a dedicated
circuit through a 10 AMP maxim um breaker or fuse and should not supply power to any other
devices. NOT FOR USE IN CLASSIFIED AREAS.

WATER SUPPLY:

Model 9001 2.4 gpm minimum required to activate flow switch.
Model 9001.5 1.5 gpm minimum required to activate flow switch.
Mount flow switch in supply line with flow in horizontal direction and switch stem extending
vertically from tee. Mount switch with at least 6” of straight pipe on both sides to minimize
turbulence in switch.

1. Alarm horn and light do not

1. a. Check incoming circuit for power and power

b. Check that the direction of water flow

corresponds to the arrow on the flow switch

c. Check that the switch located on the junction

g. Faulty flow switch. Replace entire switch

2. Horn sounds but light does not

3. Light flashes but horn does not

2. a. Check wiring connections.

3.

a. Check wiring connections.

b. Make sure the alarm silencing switch is in

10/17 9001 Alarm Series Page 2 of 6

b. Disconnect flow switch wires and test for

continuity.