Page 1
INSTALLATION, OPERATION
MAINTENANCE IN STRUCTIONS
&
1455 Kleppe Lane Sparks, NV 89431-6467 (775) 359-4712 Fax (775) 359-7424
E-mail: haws@hawsco.com website: www.hawsco.com
No. 2080210(11)
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
HAWS warrants that this specific product is guaranteed against defective material or poor
workmanship for a period of one year from date of shipment. HAWS liability under this
warranty shall be discharged by furnishing without charge F.O.B. HAWS Factory any goods,
or part thereof, which shall appear to the Company upon inspection to be of defective
material or not of first class workmanship, provided that claim is made in writing to Haws
within a reasonable period after receipt of the product. Where claims for defects are made,
the defective part or parts shall be delivered to the Company, prepaid, for inspection. HAWS
will not be liable for the cost of repairs, alterations or replacements, or for any expense
connected therewith made by the owner or his agents, except upon written authority from
HAWS, Sparks, Nevada. HAWS will not be liable for any damages caused by defective
materials or poor workmanship, except for replacements, as provided above. Buyer agrees
that Haws has made no other warranties either expressed or implied in addition to those
above stated, except that of title with respect to any of the products or equipment sold
hereunder and that HAWS shall not be liable for general, special, or consequential
damages claimed to arise under the contract of sale.
The emergency equipment manufactured by HAWS is warranted to function if installation
and maintenance instructions provided are adhered to. The units also must be used for the
purpose for which they were intended. This product is intended to supplement first-aid
treatment. Due to widely varying conditions, Haws cannot guarantee that the use of this
emergency equipment will prevent serious injury or the aggravation of existing or prior
injuries.
NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED, PROVIDED
OR GIVEN BY HAWS.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:
TECHNICAL SUPPORT: 1-800-766-5612
FOR CUSTOMER SERVICE: 1-888-640-4297
Model 8905
Hose Spray
LIMITED WARRANTY
11/14 Model 8905 Page 1 of 4
Page 2
LOCATION OF UNIT: The Model 8905 Hose Spray should be installed in close
proximity to potential accident areas. It should be clearly identified free from
obstructions and easy to access. In order to comply with state codes, the use of a
vacuum breaker is required with all hand held eye/face wash and body spray units
(Haws offers Model SP212).
SUPPLY LINE: The minimum recommended line size is 1/2" IPS with 30-90 psi (2-6
ATM) flowing pressure. Where sediment or mineral content is a problem, an inlet filter
is recommended.
PLUMBING CONNECTIONS: Inlet supply is 1/2” NPT.
TROUBLESHOOTING
PROBLEM REPAIR CHECKLIST
1. No flow. 1. a. Check the main shut-off valve.
2. Insufficient water flow. 2. a. Verify minimum 30 psi (2 ATM)
flowing supply line pressure.
b.
Probable clogging of flow control
due to inadequate line flushing.
Unscrew eye/face wash head and
remove the four screws to
disassemble the head. Clean flow
control and reassemble head. See
SP65 Installation Drawing for
details.
INSTALLATION INSTRUCTIONS
Refer to installation drawing to clarify installation procedure.
STEP 1: Assemble eye/face wash assembly to hose, orient tab on assembly away from user.
For more information about Haws products, see our website: www.hawsco.com
© 2014 Haws
HAWS
®
®
Corporation – All Rights Reserved
and other trademarks used in these materials are the exclusive property of Haws Corporation.
11/14 Model 8905 Page 2 of 4
Page 3
THIS DOCUMENT IS TRUE AND CORREC T AT TI ME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENT S
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
PARTS BREAKDOWN
VALVE ASSEMBLY
SP248
SP42
FLOW CONTROL
6.25 GPM
SP170
TEST TAG
VRKSP248
VALVE REPAIR KIT
SP175
EYEWASH
SIGN
SP65 EYE/FACE WASH ASSEMBLY
(INCLUDES: EYEFACE WASH HEAD ( )
EYEWASH HEAD (
CONTRO L (
ADAPTER (
0003106754
HOSE, RECOIL
BYECN NO.
REVISED PER
ECN:
DRAWN
WHEN ORDERING PARTS PLEASE SPECIFY MODEL NUMBER.
C
2014
Haws Corporation - All Rights Reserved
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
R
APPROVED
4938
DATE
CH
08/04/95
FV
DATE
01/08/15
VWC
CHKD
MODEL(S)
SCALE:
1:4
WALL MTD EYE/FACE WASH
8905
DRAWING TYPE: SIZE: A
PARTS BREAKDOWN
), EYEWASH FLOW
), DUST COVER ( ),
SPARKS, NEVADA 89431
(775) 359-4712 FAX (755) 359-7424
E-MAIL: HAWS@HAWSCO.COM
WEBSITE: WWW.HAWSCO.COM
))
1455 KLEPPE LANE
PART NUMBER
0002080210
DRAWING NO.
12085C00 11
SHEET OF
PAGE
3 of 4
REV
11
Page 4
C
Haws Corporat ion - All Rights Reserved.
2014
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
*
4. MOUNTING HARDWARE SUPPLIED BY OTHERS.
- EYEWASH OR EYE/FACE WASH SHALL BE POSITIONED WITH NOZZLES NOT
LESS THEN 83.8 CM (33 IN.) AND NO GREATER THAN 114.3 CM (45 IN.) FROM
SURFACE ON WHICH USER STANDS AND 15.3 CM (6 IN.) MINIMUM FROM WALL
OR NEAREST OBSTRUCTION.
3. TO COMPLY WITH ANSI Z358.1-2009 FOR EMERGENCY EYEWASH OR EYE/FACE
WASH EQUIPMENT:
- UNIT SHALL BE INSTALLED IN ACCORDANCE WITH MANUFACTURER'S
INSTRUCTIONS AND ACCEPTABLE PLUMBING PRACTICES.
2. IN ORDER TO COMPLY WITH STATE CODES, THE USE OF A VACUUM BREAKER
IS REQUIRED WITH ALL HAND HELD EYE/FACE WASH AND BODY SPRAY UNITS
(HAWS OFFERS MODEL SP212).
NOTES:
1. DIMENSIONS MAY VARY ±1/2" (12.7mm).
375mm
14 3/4"
38mm
1 1/2"
9/32"
*4X
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
HAWS and other trademarks used in these m aterials are the exclusive p r operty of Haws Corporation.
4X
216mm
8 1/2"
51mm
2"
R
838mm TO 1397mm
102mm
4"
33" TO 45 "
5 ASSEMBLE EYE/FACE WAS ASSEMBLY TO HOSE; ORIENT TAB
ON ASSEMBLY AWAY FROM USER.
APPROVED:
DRAWN:
CH
FV
REVISED PER
ECN:
DATE:
08/95
4938
DATE:
01/08/15
BY:ECN NO.
CHK'D.:
VWC
SCALE:
MODEL(S)
1:4
WALL MTD EYE/FACE WASH
DRAWING TYPE: SIZE: A
FLOOR LINE
273mm
10 3/4"
241mm
9 1/2"
WALL
5
8905
INSTALLATION
0002080210.D
DRAWING NO.
PART NUMBER
SHEET OF
12086A00 11
11
REV
WEBSITE: WWW.HAWSCO.COM
(775) 359-4712 FAX (755) 359-7424
E-MAIL: HAWS@HAWSCO.COM
SPARKS, NEVADA 89431
1455 KLEPPE LANE
1/2" IPS
SUPPLY
PAGE
4 of 4
Loading...