Haws 8901B User Manual

INSTALLATION, OPERATION

&

MAINTENANCE INSTRUCTIONS

1455 Kleppe Lane Sparks, NV 89431-6467 [phone] Fax [phone]

E-mail: [e-mail]  website: www.hawsco.com

NOTE TO INSTALLER: Please leave this information with the Maintenance Department.

HAWS® warrants that all of its products are guaranteed against defective material or poor
workmanship for a period of one year from date of shipment. HAWS liability under this
warranty shall be discharged by furnishing without charge F.O.B. HAWS Factory any
goods, or part thereof, which shall appear to the Company upon inspection to be of
defective material or not of first class workmanship, provided that claim is made in writing
to company within a reasonable period after receipt of the product. Where claims for
defects are made, the defective part or parts shall be delivered to the Company, prepaid,
for inspection. HAWS will not be liable for the cost of repairs, alterations or replacements,
or for any expense connected therewith made by the owner or his agents, except upon
written authority from HAWS, Sparks, Nevada. HAWS will not be liable for any damages
caused by defective materials or poor workmanship, except for replacements, as provided
above. Buyer agrees that Haws has made no other warranties either expressed or implied
in addition to those above stated, except that of title with respect to any of the products or
equipment sold hereunder and that HAWS shall not be liable for general, special, or
consequential damages claimed to arise under the contract of sale.

The emergency equipment manufactured by HAWS is warranted to function if installation
and maintenance instructions provided are adhered to. The units also must be used for
the purpose, which they were intended. This product is intended to supplement first-aid
treatment. Due to widely varying conditions HAWS cannot guarantee that the use of this
emergency equipment will prevent serious injury or the aggravation of existing or prior
injuries.

NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED,
PROVIDED OR GIVEN BY HAWS.

SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL, PLEASE CALL:

FOR PARTS CALL:

(U.S.A. AND CANADA ONLY) MONDAY-THURSDAY: 6:00 A.M. – 4:00 P.M. PST

Model 8901B

Hose Spray

LIMITED WARRANTY

1-800-766-5612

1-800-758-9378

FRIDAY: 6:00 A.M – 1:00 P.M. PST

No. 2080191(8)

12/09 Model 8901B Page 1 of 4

LOCATION OF UNIT: The Model 8901B Hose Spray should be installed in close
proximity to potential accident areas. It should be clearly identified free from
obstructions and easy to access. In order to comply with state codes, the use of a
vacuum breaker is required with all hand held eye/face wash and body spray units
(Haws offers Model SP212).

Supply Line: The minimum recommended line size is 1/2” IPS with 30-90 psi (2-6
ATM) pressure. Where sediment or mineral content is a problem, an inlet filter is
recommended.

Plumbing Connections: Inlet supply is male 1/2” IPS.

TROUBLESHOOTING

1. No flow. 1. a. Check the main shut-off valve.

2. Insufficient water flow. 2. a. Verify minimum 30 psi (2 ATM)

b

c. Unscrew eye/face wash head cap

3. Valve leaks in shut-off position. 3. Refer to installation drawing. Clean

PROBLEM

REPAIR CHECKLIST

flowing supply line pressure.

Probable clogging of flow control
due to inadequate line flushing.
Disassemble eyewash at inlet
connection to gain access and
clean rubber flow control.

off to gain access to the buffer and
clean it.

valve washer and seat thoroughly,
then reassemble the valve. If valve
still leaks, contact HAWS and
purchase VRKSP248 to repair
valve.

For more information about Haws products, see our website: www.hawsco.com

© 2009 Haws® Corporation – All Rights Reserved
HAWS

12/09 Model 8901B Page 2 of 4

®

and other trademarks used in these materials are the exclusive property of Haws Corporation.