No. 2080150(7)
Model 8356WCSM
Pull-Down Shower Eye/Face Wash
INSTALLATION, OPERATION
&
MAINTENANCE INSTRUCTIONS
LIMITED WARRANTY
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
1455 Kleppe Lane Sparks, NV 89431-6467 (775) 359-4712 Fax (775) 359-7424
E-mail: haws@hawsco.com website: www.hawsco.com
HAWS warrants that this specific product is guaranteed against defective material or poor
workmanship for a period of one year from date of shipment. HAWS liability under this
warranty shall be discharged by furnishing without charge F.O.B. HAW S Factory any goods,
or part thereof, which shall appear to the Company upon inspection to be of defective
material or not of first class workmanship, provided that claim is made i n writing to Haws
within a reasonable period after receipt of the product. Where claims for defects are made,
the defective part or parts shall be delivered to the Company, prepaid, for inspection. H AWS
will not be liable for the cost of repairs, alterations or replacements, or for any expense
connected therewith made by the owner or his agents, except upon written authority from
HAWS, Sparks, Nevada. HAWS will not be liable for any damages caused by defective
materials or poor workmanship, except for replacements, as provided above. Buyer agrees
that Haws has made no other warranties either expressed or implied in addition to those
above stated, except that of title with respect to any of the products or equipment sold
hereunder and that HAWS shall not be liable for general, special, or consequential damages
claimed to arise under the contract of sale.
The emergency equipment manufactured by HAWS is warranted to function if installation
and maintenance instructions provided are adhered to. The units also must be used for the
purpose for which they were intended. This product is intended to supplement first-aid
treatment. Due to widely varying conditions, Haws cannot guarantee that the use of this
emergency equipment will prevent serious injury or the aggravation of existing or prior
injuries.
NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED, PROVIDED OR
GIVEN BY HAWS.
MODEL PLEASE CALL:
TECHNICAL SUPPORT: 1-800-766-5612
FOR CUSTOMER SERVICE: 1-888-640-4297
12/16 Model 8356WCSM Page 1 of 5
INSTALLATION PROCEDURE
1.
Install all items at dimensions shown in installation drawing.
2.
Once valve assembly is installed, install mounting frame(s) over valve assembly.
3.
IMPORTANT: Showerhead must be positioned in-line with eye/face wash to allow for
4.
Install remaining items to dimensions shown.
5.
Each unit is factory preset to meet the 5 pound (22.2 N) maximum activation force
a)
Locate the two ball detents, one on each side of the eyewash tray. See installation
b)
Using a flat screwdriver, adjust each ball detent to make slight contact with the
c)
Once both ball detents are adjusted as above, tighten each ball detent ¼ turn.
d)
Using a force gauge, ensure the force required to open the eyewash unit does not
CLEANING INSTRUCTIONS FOR STAINLESS B EAD-BLASTED PRODUCTS
will resist new stains and fingerprints.
RECOMMENDED TOOLS: Adjustable wrench, pipe wrench, pipe joint sealant, Phillips
screw driver, ¼” hex key wrench.
LOCATION OF UNIT: The Model 8356WCSM eye/face wash should be installed in close
proximity to potential accident areas. It should be clearly identified free from obstructions
and easy to access. See ANSI Z358.1 guidelines for more information.
SUPPLY LINE: The minimum recommended line size is 1" IPS with 30-90 psi (2-6 ATM)
flowing pressure at supply inlet. Where sediment or mineral content is a problem, an inlet
filter is recommended.
PLUMBING CONNECTIONS: Inlet supply is male 1" IPS; waste is 2” IPS.
Refer to installation drawing for clarification. Check Parts List to ensure all required parts are
included.
simultaneous use by the same user per ANSI Z358.1.
requirement for disabled persons. If adjustment is required after installation, follow the
adjustment directions below.
drawing.
eyewash housing just before the ball detent snaps into its locating position on the
housing.
exceed 5 pounds (22.2 N).
Haws recommended cleaning procedure for stainless bead blasted products is as follows:
1. Use a stainless steel polish and cleaner for removing stains and finger prints.
2. Spray cleaner onto stainless surfaces and wipe dry with clean cloth. Cleaned surface
12/16 Model 8356WCSM Page 2 of 5
INCLUDED PARTS
MO DEL PACKAGE
QUANTITY
ITEMS INCLUDED
8356WCSM
1
Mounting Frame/Eyewash assembly
1 Surface Mount Frame
1 Valve assembly
1 Handle/screw assembly
1 Showerhead
1 1” x 32-1/2” Nipple
1 1” elbow 1
1” Street elbow
1 Emergency Eyewash/shower sign
1 Test Tag
1 1” X 46” Nipple
1 1” X 9-1/2” Nipple
TROUBLESHOOTING
PROBLEM
REPAIR CHECKLIST
Remove cap located on in-line strainer
installation drawing for location.
4.
5.
1. No flow. 1. Check the main shut-off valve.
2. Insufficient water flow at eye/face
wash.
2a. Verify minimum 30 psi (2 ATM) flowing
supply line pressure.
b. Probable clogging of flow control due to
inadequate line flushing. Unscrew eye/face
wash head and remove the four screws to
disassemble the head. Clean the flow
control and reassemble head.
c.
housing using a ¼” Allen wrench to
access and clean filter sc r een. See
3. Eye/face wash streams do not meet
desired eye level.
b. Possible non-leveled eye/face wash
c. Possible low supply pressure.
4. Insufficient water flow at the
showerhead, however, eye/face
wash is sufficient.
3a. Possible blocked flow control, see above
solution.
assembly.
Probable clogging of flow control inside
showerhead. Remove showerhead by
unscrewing it and clean rubber flow control.
5. Tray too hard to open or does not
stay closed.
For more information about Haws products, see our website: www.hawsco.com.
© 2016 Haws
HAWS
12/16 Model 8356WCSM Page 3 of 5
®
®
Corporation – All Rights Reserved
and other trademarks used in these materials are the exclusive property of Haws Corporation.
See “Installation Procedure” Step 5.
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
PARTS BREAKDOWN
3
ITEM DESCRIPTION
1
TEST TAG
2
SHOWER/EYEWASH SIGN
SHOWER HEAD
3
4
SHOWER BALL VALVE
FLOW CONTROL
5
65EYE/FACE WASH
VALVE REPAIR KIT7
PART NO.
SP170
SP178
SP829SS
1" IPS
0003138392
SP65PD
VRK7650
6
7
4
2
1
BYECN NO.
REVISED PER
4290
ECN:
5162
DATE
DRAWN
I. ROBERTS
WHEN ORDERING PARTS PLEASE SPECIFY MODEL NUMBER.
C
2016
Haws Corporation - All Rights Reserved
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
R
APPROVED
FV
07/21/10
DATE
CHKD
02/23/17
VWC
VWC
MODEL(S)
1/8
SCALE:
8356WCSM
DRAWING TYPE: SIZE: A
PARTS BREAKDOWN
1455 KLEPPE LANE
SPARKS, NEVADA 89431
(775) 359-4712 FAX (775) 359-7424
E-MAIL: HAWS@HAWSCO .COM
WEBSITE: WWW.HAWSCO.COM
PAGE
PART NUMBER
0002080150
REVISION
7
SHEET OF
11
4 of 5
C
Haws Corporation - All Rights Reserved.
2017
1-11/16"
43mm
FEMALE OUTLET
167mm
6-9/16"
2" NPT
ACCESS PANELS
(NOT SHOWN)
REMOVABLE
IN-LINE STRAINER
HOUSING
INLET
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
108mm
4-1/4"
3-13/16"
97mm
1-11/16"
43mm
R
SUPPLY
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
FOR ACTIVATING
EYE/FACE WASH
"PANIC BAR"
826mm
32-1/2"
572mm
22 1/2"
292mm
23-9/16"
598mm
FEMALE
1" IPS
UNION
1" IPS BRASS
AND OUTLET
BALL VALVE
STAY OPEN
WITH INLET
WITH 20 GPM FLOW CONTROL
2
STAINLESS STEEL
SHOWER HEAD
11 1/4"
1 X 46" S.S. NIPPLE
(SUPPLIED)
HANGER BRACKET
(NOT SUPPLIED)
1 X 9 1/2" SST NIPPLE
(SUPPLIED)
APPROVED:
DRAWN:
I. ROBERTS
FV
DATE:
7/13/10
DATE:
02/23/17
CHK'D.:
VWC
SCALE:
1/19
DRAWING TYPE: SIZE: A
8356WCSM
INSTALLATION
4290
ECN:
5162
VWC
489mm
19-1/4"
292mm
11-1/2"
MOUNTING
Ø3/16"
4.8mm
HOLE
*
IN THE OFF POSITION
6X
*
5.
4.
3.
MOUNTING HARDWARE NOT SUPPLIED.
FLOW RATE FOR EYE/FACE WASH IS 3.7 GPM AND EXCEEDS ANSI STANDARD Z358.1.
DIMENSIONS MAY VARY BY ± 1/2" [12.7mm].
Ø 10-1/2"
1 X 32-1/2" S.S. NIPPLE
(911mm)
(35-7/8")
267mm
(SUPPLIED)
"PANIC BAR"
SHOWER
95mm
3-3/4"
2
SHOWER HEAD MUST BE POSITIONED IN-LINE WITH EYE/FACEWASH HEAD TO ALLOW FOR
SIMULTANEOUS USE BY THE SAME USER PER ANSI STANDARD Z358.1.
1.
NOTES:
WHEN INSTALLING THIS UNIT, LOCAL, STATE OR FEDERAL CODES SHOULD BE ADHERED TO.
WASTE CONNECTION MUST ADHERE TO LOCAL HEALTH AND PLUMBING CODES.
584mm
23"
REVISED PER
(2148mm)
POSITION
(84-1/2")
ACTIVATION
BY:ECN NO.
(1206mm)
MODEL(S)
(879mm)
(34-5/8")
FLOOR LINE
2X
DETENT
BALL
(752mm)
(29-5/8")
(775) 359-4712 FAX (775) 359-7424
E-MAIL: HAWS@HAWSCO.COM
WEBSITE: WWW.HAWSCO.COM
SPARKS, NEVADA 89431
1455 KLEPPE LANE
524mm
20-5/8"
470mm
18-1/2"
(47-1/2")
EYE/FACE WASH
TO OPEN
PULL DOWN
0002080150.D
PART NUMBER
REVISION
SHEET OF
11
7
PAGE
5 of 5
Loading...