INSTALLATION, OPERATION
&
MAINTENANCE INSTRUCTIONS
1455 Kleppe Lane Sparks, NV 89431-6467 (775) 359-4712 Fax (775) 359-7424
E-mail: haws@hawsco.com website: www.hawsco.com
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
HAWS warrants that this specific product is guaranteed against defective material or poor
workmanship for a period of one year from date of shipment. HAWS liability under this
warranty shall be discharged by furnishing without charge F.O.B. HAWS Factory any
goods, or part thereof, which shall appear to the Company upon inspection to be of
defective material or not of first class workmanship, provided that claim is made in writing to
Haws within a reasonable period after receipt of the product. Where claims for defects are
made, the defective part or parts shall be delivered to the Company, prepaid, for inspection.
HAWS will not be liable for the cost of repairs, alterations or replacements, or for any
expense connected therewith made by the owner or his agents, except upon written
authority from HAWS, Sparks, Nevada. HAWS will not be liable for any damages caused by
defective materials or poor workmanship, except for replacements, as provided above.
Buyer agrees that Haws has made no other warranties either expressed or implied in
addition to those above stated, except that of title with respect to any of the products or
equipment sold hereunder and that HAWS shall not be liable for general, special, or
consequential damages claimed to arise under the contract of sale.
The emergency equipment manufactured by HAWS is warranted to function if installation
and maintenance instructions provided are adhered to. The units also must be used for the
purpose for which they were intended. This product is intended to supplement first-aid
treatment. Due to widely varying conditions, Haws cannot guarantee that the use of this
emergency equipment will prevent serious injury or the aggravation of existing or prior
injuries.
Combination Shower Eye/Face Wash
Model 8330 Stainless Steel
LIMITED WARRANTY
NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED, PROVIDED
No. 2080174(23)
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:
TECHNICAL SUPPORT: 1-800-766-5612
FOR CUSTOMER SERVICE: 1-888-640-4297
02/14 Model 8330 Page 1 of 5
LOCATION OF UNIT: The Model 8330 Stainless Steel combination Shower
Eye/Face Wash should be installed in close proximity to potential accident areas. It
should be clearly identified, free from obstructions and easy to access.
SUPPLY LINE: The minimum recommended line size is 1-1/4” IPS with 30-90 psi (26 ATM) flowing pressure. Where sediment or mineral content is a problem, an inlet
filter is recommended.
PLUMBING CONNECTIONS: Inlet supply is female 1-1/4” IPS. Waste outlet is
female 1-1/4” IPS.
INSTALLATION PROCEDURE
Refer to Installation Drawing for clarification. Check parts list to insure all required parts
are included. Use pipe joint sealant PST #567 (Loctite) on all connections.
STEP 1: Prepare the emergency shower foundation by using the floor flange as a
template. Locate the three holes for the 3/8-16 UNC x 6” anchor bolts.
(Not supplied). They should extend 1” above the floor level.
STEP 2: Once the concrete foundation is ready (dry), assemble the floor flange to
the anchor bolts; then securely fasten with 3/8-16 UNC Hex nuts and 3/8”
washers (Not supplied). Seal and tighten floor flange and (1-1/4”) tee
making certain the waste tee is facing the proper location and the foot
control holes are facing side to side.
STEP 3: Assemble nipple (1-1/4” x 21-1/2”) to the tee and tighten with a pipe
wrench.
STEP 4: Assemble the eye/face wash loop assembly to the (21-1/2”) nipple from
Step three. Connect the pipe wrench to the nipple between the two tees to
avoid damage.
STEP 5: Assemble in the following order:
Attach nipple (1-1/4” x 24”) onto the loop assembly.
Attach nipple (1-1/4” x 24”) onto the tee.
Attach tee (1-1/4” x 1-1/4” x 1”) onto nipple.
Attach nipple (1” x 8”) and valve assembly onto tee.
Attach street el (1”) and nipple (1” x 12-1/2”) onto valve.
STEP 6: Assemble showerhead onto street el (1”). If necessary, use Dow Corning
832 sealant placing 5 small beads on the male threads, just above the first
thread.
STEP 7: Assemble the sign onto the unit. Use the strap, screws, washers and nuts
provided to mount the sign onto the upright. The sign should be positioned
for maximum visibility.
STEP 8: Insert the plug into the optional supply line tee that is not used. Before
connecting the supply water line to the emergency shower; FLUSH THE
LINE THOROUGHLY.
02/14 Model 8330 Page 2 of 5
TROUBLESHOOTING
PROBLEM
1. No flow.
2. Insufficient water flow. 2. Verify minimum 30 psi (2 ATM)
3. Insufficient water flow on eye/face
wash, however, shower is
sufficient.
b. Probable clogging of flow control due
c. Remove plug located on L – Strainer
4. Eye/face wash streams do not
meet desired eye level.
REPAIR CHECKLIST
1.
Check the main shut-off valve.
flowing supply line pressure.
3. a. Verify minimum 30 psi (2 ATM)
flowing supply line pressure.
to inadequate line flushing. Unscrew
eye/face wash head and remove the
four screws to disassemble head.
Clean flow control and reassemble
head.
using a 9/16” wrench to access and
clean filter screen.
4. Possible blocked flow control, see
above solution. Possible non-leveled
eye/face wash assembly.
5. Water does not drain properly. 5. Check your drain system for debris.
Check the main waste line of your
building to see if it does handle the
capacity required for the entire
drainage system.
6. Water leak between joints or
fittings.
6. Tighten loose connections. If leak
persists, the application of hot water
will sometimes reseat improperly
applied joint compound. After 30
minutes wait and retest. A persistent
leak will necessitate reassembly and
additional sealant.
7. Insufficient water flow from
shower, however, eye/face wash
is sufficient.
7. Probable clogging of flow control
inside showerhead. Unscrew
showerhead off of elbow and clean
rubber flow control.
For more information about Haws products, see our website: www.hawsco.com
© 2014 Haws® Corporation – All Rights Reserved
HAWS
®
and other trademarks used in these materials are the exclusive property of Haws Corporation.
02/14 Model 8330 Page 3 of 5
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
PARTS BREAKDOWN
2
1
DESCRIPTIONITEM
SP829SS SH OWE R HE AD1
SP265 VALVE ASSEM BLY
2
SP200 PULL ROD
3
SP65SS EYE/FACE WASH HEAD
4
SP228 VALVE ASSEM BLY
5
SP185 STRIPE TAPE
6
SP178 SHOWER SIGN
7
8
SP90 BOWL
9
OPTIONAL
7
SP220SS FOOT TRE ADLE
10
SP170 TEST TAG
11
SP509SS L-ST RA INE R
12
9102 DUST COVER ASSEMBLY
10
3
DUST COVER
(OPEN POSITION)
8
11
6
12
TEST THIS UNIT EACH WEEK
4
5
SP65SS EYE/FACE WASH ASSEMBLY
OPTIONAL
WHEN ORDERING PARTS PLEASE SPECIFY YOUR MODEL NUMBER
C
Haws Corporation - All Rights Reserved
2014
R
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
9
REVISED PER
ECN:
4888
DATE:
05/91
DATE:
BY:
MODEL(S)
HM
CHK'D.:
8330
SS SHOWER EYE/FACE WASH
DRAWING TYPE:SCALE:
1/6 PARTS BREAKDOWN
ECN NO.
DRAWN:
CJL
APPROVED:
1455 KLEPPE LANE
SPARKS, NEVADA 89431
(775) 359-4712 FAX (775) 359-7424
E-MAIL: HAWS @HA WS CO .C O M
WEBSITE: WWW.HAWSCO.COM
A
Page
PART NUMBER:
0002080174
DRAWING NO.:
11499C00
SHEETSIZE: OF
4 of 5
REV.
1231
C
Haws Corporation - All Rights Reserved
2014
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
NOTES:
1. DIMENSIONS MAY VARY BY ± 1/2 INCH [13mm] .
2. TO COMPLY WITH AN SI Z358.1 -2009 FOR EMERGENC Y EYEWAS H OR EYE/F ACE WASH AND SHOWER EQUIPMENT:
- UNIT SHALL BE INSTALLED IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS AND ACCEPTABLE PLUMBING PRACTICES.
- EYEWASH OR EYE/FACE WASH SHALL BE POSITIONED WITH NOZZLES NOT LESS THEN 83.8 CM (33 IN. ) AND NO GREATER THAN
114.3 CM (45 IN.) FROM SURFACE ON WHICH USER STANDS AND 15.3 CM (6 IN.) MINIMUM FROM WALL OR NEAREST OBSTRUCTION.
- SHOWER SHALL BE POSITIONED SO THAT SHOWER HEAD IS NOT LESS THAN 208.3 CM (82 IN.) NOR MORE THAN 243.8 CM (96 IN.)
FROM SURFACE ON WHICH USER STANDS.
- SHOWER SPRAY PATTERN SHALL HAVE A MINIMUM DIAMETER OF 5 0. 8 CM (20 IN.) AT 152. 4 CM (60 IN.) ABOVE SURFACE ON WHICH
USER STANDS, AND CENTER OF SPRAY PATTERN SHA LL BE LOCATED AT LEAST 40.6 CM (16 IN.) FROM ANY OBSTRUCTION.
3 IF NECESSARY USE LOCTITE 567 SEALANT ON THE MALE THREADS, JUST ABOVE THE FIRST THREAD.
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
R
1077mm
42-3/8"
2127mm
83-3/4"
MOUNTING DETAIL
30°
Ø229mm
Ø9"
Ø203mm
Ø8"
3X
B.C.
Ø10mm
Ø3/8"
279mm
11"
(OPEN POSITION)
DUST COVER
SCALE: SHEET OF
1/16
DRAWING TYPE :
INSTALLATION
SIZE:
A
C HAYES
APPROVED:
DRAWN:
DATE:
05/91
DATE:
CHK'D.:
8330
SS SHOWER EYE/FACE WASH
09468A00230002080174.D
DRAWING NO.:
HM
REVIS ED PER
ECN:
4888
BY:ECN NO.
MODEL(S)
(775) 359-4712 FAX (775) 359- 7424
WEBSITE: WWW.HAWSCO.COM
E-MAIL: HAWS@HAWSCO.COM
SPARKS, NEVADA 89431
1455 KLEPPE LANE
PART NUMBER:
171mm
6-3/4"
L-STRAINER
FLOOR LINE
SP220SS
OPTIONAL
3
756mm
29-3/4"
259mm
WASTE 1-1/4" IPS
1588mm
62-1/2"
10-3/16"
702mm
27-5/8"
SUPPLY
1-1/4" IPS
1
1
REV.
DWG. NO.
09468A00
Page
5 of 5
Loading...