INSTALLATION, OPERATION
&
MAINTENANCE INSTRUCTIONS
1455 Kleppe Lane Sparks, NV 89431-6467 (775) 359-4712 Fax (775) 359-7424
E-mail: haws@hawsco.com website: www.hawsco.com
No. 2080170(19)
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
HAWS warrants that this specific product is guaranteed against defective material or poor
workmanship for a period of one year from date of shipment. HAWS liability under this
warranty shall be discharged by furnishing without charge F.O.B. HAWS Factory any
goods, or part thereof, which shall appear to the Company upon inspection to be of
defective material or not of first class workmanship, provided that claim is made in writing
to Haws within a reasonable period after receipt of the product. Where claims for defects
are made, the defective part or parts shall be delivered to the Company, prepaid, for
inspection. HAWS will not be liable for the cost of repairs, alterations or replacements, or
for any expense connected therewith made by the owner or his agents, except upon
written authority from HAWS, Sparks, Nevada. HAWS will not be liable for any damages
caused by defective materials or poor workmanship, except for replacements, as provided
above. Buyer agrees that Haws has made no other warranties either expressed or implied
in addition to those above stated, except that of title with respect to any of the products or
equipment sold hereunder and that HAWS shall not be liable for general, special, or
consequential damages claimed to arise under the contract of sale.
The emergency equipment manufactured by HAWS is warranted to function if installation
and maintenance instructions provided are adhered to. The units also must be used for the
purpose for which they were intended. This product is intended to supplement first-aid
treatment. Due to widely varying conditions, Haws cannot guarantee that the use of this
emergency equipment will prevent serious injury or the aggravation of existing or prior
injuries.
NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED, PROVIDED OR
GIVEN BY HAWS.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL, PLEASE CALL:
Model 8320-8325/8320CRP
Shower and Eye/Face Wash
LIMITED WARRANTY
1-800-766-5612
FOR PARTS CALL:
1-888-640-4297
04/14 Model 8320-8325/8320CRP Page 1 of 5
LOCATION OF UNIT: The Model 8320/8320CRP/8325 Emergency Shower should
be installed in close proximity to potential accident areas. It should be clearly
identified, free from obstructions and easy to access.
SUPPLY LINE: The minimum recommended line size is 1-1/4” IPS with 30-90 psi
(2-6 ATM) flowing pressure. Where sediment or mineral content is a problem, an
inlet filter is recommended.
PLUMBING CONNECTIONS: Inlet supply is female 1-1/4” IPS. Waste outlet is
female
1-1/4” IPS.
INSTALLATION PROCEDURE
Refer to Installation Drawing for clarification. Use pipe joint sealant PST #565 (Loctite)
on all connections.
STEP 1: Prepare the emergency shower foundation by using the floor flange
assembly as a template.
STEP 2: Once the foundation is ready, fasten the floor flange to the foundation.
Use minimum 3/8” fasteners (not supplied).
STEP 3: Assemble lower tee (1-1/4”) to the floor flange.
STEP 4: Attach nipple (1-1/4” x 21-1/2”) and eyewash loop assembly to lower tee
and tighten, grabbing the waste bend of loop assembly for leverage.
STEP 5: Attach nipple (1-1/4” x 24”) and tee (1-1/4”) to loop assembly and tighten.
STEP 6: Attach nipple (1-1/4” x 24”) and tee (1-1/4” x 1-1/4” x 1”) and tighten.
STEP 7: Attach valve assembly with nipple (1” x 9”) to tee and tighten with a spud
wrench.
STEP 8: Assemble the street elbow (1”) onto nipple (1” x 12-1/2”).
Attach nipple onto valve.
STEP 9: Attach showerhead onto street elbow (1”).
STEP 10: Assemble the sign onto the unit. Use the strap, screws, washers and nuts
provided to mount the sign onto the upright. The sign should be positioned
for maximum visibility.
STEP 11: Insert the plug into the optional supply line tee that is not used. Before
connecting the supply water line to the emergency shower, FLUSH THE
LINE THOROUGHLY.
04/14 Model 8320-8325/8320CRP Page 2 of 5
TROUBLESHOOTING
PROBLEM
REPAIR CHECKLIST
1. No flow. 1. Check the main shut-off valve.
2. Insufficient water flow. 2. Verify minimum 30 psi (2 ATM) flowing
supply line pressure.
3. Insufficient water flow on
eyewash, however, shower is
3. a. Verify minimum 30 psi (2 ATM) flowing
supply line pressure.
sufficient.
b. Probable clogging of flow control due to
inadequate line flushing. Unscrew
eye/face wash head and remove the
four screws to disassemble the head.
Clean flow control and reassemble
head. See SP65 Installation Drawing for
details.
c. Remove cap located on L – Strainer
using a 3/8” allen wrench to access and
clean filter screen.
4. Eyewash or face wash
streams do not meet desired
eye level or are not balanced.
4. Possible blocked flow control see above
solution. (Possible non-leveled eyewash
assembly.)
5. Insufficient water flow at the
showerhead, however,
eyewash is sufficient.
5. Probable clogging of flow control inside
shower head. Unscrew shower head off
of elbow and clean rubber flow control.
6. Water does not drain properly. 6. Check your drain system for debris.
Check the main waste line of your
building to see if it does handle the
capacity required for the entire drainage
system.
7. Water leak between joints or
fittings.
7. Tighten loose connections. If leak
persists, the application of hot water will
sometimes reseat improperly applied
joint compound. After 30 minutes wait
and retest. A persistent leak will
necessitate reassembly and additional
sealant.
For more information on Haws Products, please see our website: www.hawsco.com
© 2014 Haws
HAWS
04/14 Model 8320-8325/8320CRP Page 3 of 5
®
®
Corporation – All Rights Reserved
and other trademarks used in these materials are the exclusive property of Haws Corporation.
THIS DOCUMENT IS TRUE AND CORR ECT AT TIME OF PUBLICAT ION . CONTIN UE D PRODU CT IMPRO VEM ENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
PARTS BREAKDOW N
6
5
9
ITEM DESCRIPTION
1 SP65 EYE/FACE WASH ASSY
2
SP509 L-STR AINE R
3
SP93 BOWL
4
SP225 VALVE ASS EMBLY
SP829 SHOWER HEAD
5
6 SHOWER VALVE ASSEMBLY
7
SP178 SHOWER SIGN
8
SP75 FLOOR FLANGE
9
SP200 PULL ROD
10
SP185 STRI PE T AP E
11
SP170 TEST TAG
12
BOWL HOLDER
- VRKEWSTR STR. REPAIR KIT
7
PART NO.
11
3
2
12
4
10
1
8
SP65 EYE/FACE WASH ASSEMBLY
BYECN NO.
REVISED PER
ECN:
CLF
4910
DATE
03/12/93
DATE
WHEN ORDERING PARTS PLE ASE SPECIFY MODEL NUMBER.
C
2014
Haws Corporation - Al l Rights Res erved
HAWS and other trademarks used in these materials are the exclus i ve property of Haws Corporation.
R
DRAWN
APPROVED
HM
CHKD
MODEL(S)
SCALE:
1:1
8320-8325/8320CRP
DRAWING TYPE:
.
PARTS BREAKDOWN
1455 KLEPPE LANE
SPARKS, NEVADA 89431
(775) 359-4712 F AX (775) 359-7424
E-MA IL : HAWS@HAW SCO.COM
WEBSITE : WWW.HAWSCO.COM
PAGE
SIZE: A
PART NUMBER
0002080170
DRAWING NO.
11495C00 19
SHEET OF
11
4 of 5
REV
C
Haws Corporation - All Rights Reserved.
2014
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
NOTES :
1. DIMENSIONS MAY VARY BY ± 1/2 INCH [13mm].
2. TO COMPLY WITH ANSI Z358.1-2009 FOR EMERGENCY EYEWASH OR EYE/FACE WASH AND SHOWER EQUIPMENT:
- UNIT SHALL BE INSTALLED IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS AND ACCEPTABLE PLUMBING PRACTICES.
- EYEWASH OR EYE/FACE WASH SHALL BE POSITIONED WITH NOZZLES NOT LESS THEN 83.8 CM (33 IN.) AND NO GREATER THAN
114.3 CM (45 IN.) FROM SURFACE ON WHICH USER STANDS AND 15.3 CM (6 IN.) MINIMUM FROM WALL OR NEAREST OBSTRUCTION.
- SHOWER SHALL BE POSITIONED SO THAT SHOWER HEAD IS NOT LESS THAN 208.3 CM (82 IN.) NOR MORE THAN 243.8 CM (96 IN.)
FROM SURFACE ON WHICH USER STANDS.
- SHOWER SPRAY PATTERN SHALL HAVE A MINIMUM DIAMETER OF 50.8 CM (20 IN.) AT 152.4 CM (60 IN.) ABOVE SURFACE ON WHICH
USER STANDS, AND CENTER OF SPRAY PATTERN SHALL BE LOCATED AT LEAST 40.6 CM (16 IN.) FROM ANY OBSTRUCTION.
3. DO NOT USE REGULAR PIPE SEALANT. IF NECESSARY USE DOW CORNING 832 SEALANT PLACING 5 SMALL BEADS ON THE MALE
THREADS, JUST ABOVE THE FIRST THREAD.
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
1661mm
65
SP829
3
286mm
11
4
1
"
FLOOR LINE
2096mm
82
2
"
3
8
"
1
L-STRAINER
635mm
25"
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
R
1061mm
41
4
"
235mm
3
9
3
8
"
167mm
6
5
8
"
1-1/4"
IPS
APPROVED:
DRAWN:
SLS
REVISE D PER
ECN:
DATE:
5/1/08
4910
DATE:
CHK'D.:
BY:ECN NO .
HM
SCALE:
MODEL(S)
WASTE
1575mm
699mm
62"
27
2
"
1
1-1/4"
IPS
SUPPLY
2266mm
89
1
4
"
1:1
DRAWING TYPE: SIZE: A
8320-8325/8320CRP
INSTALLATION
0002080170.D
DRAWING NO.
PART NUMBER
SHEET OF
09460A00
11
REV
19
30°
SCALE 10:1
TOP VIEW
(775) 359-4712 FAX (775) 359-7424
E-MA IL: HAW S@HAWSCO.COM
WEBSITE: WWW.HAWSCO.COM
SPARKS, NEVADA 89431
1455 KLEPPE LANE
ø
203mm
8"
9.5mm
3X ø
3/8"
B.C.
229mm
ø
9"
PAGE
5 of 5
Loading...