INSTALLATION, OPERATION
&
MAINTENANCE INSTRUCTIONS
1455 Kleppe Lane Sparks, NV 89431-6467 (775) 359-4712 Fax (775) 359-7424
E-mail: haws@hawsco.com website: www.hawsco.com
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
HAWS warrants that this specific product is guaranteed against defective material or poor
workmanship for a period of one year from date of shipment. HAWS liability under this
warranty shall be discharged by furnishing without charge F.O.B. HAWS Factory any goods,
or part thereof, which shall appear to the Company upon inspection to be of defective
material or not of first class workmanship, provided that claim is made in writing to Haws
within a reasonable period after receipt of the product. Where claims for defects are made,
the defective part or parts shall be delivered to the Company, prepaid, for inspection. HAWS
will not be liable for the cost of repairs, alterations or replacements, or for any expense
connected therewith made by the owner or his agents, except upon written authority from
HAWS, Sparks, Nevada. HAWS will not be liable for any damages caused by defective
materials or poor workmanship, except for replacements, as provided above. Buyer agrees
that Haws has made no other warranties either expressed or implied in addition to those
above stated, except that of title with respect to any of the products or equipment sold
hereunder and that HAWS shall not be liable for general, special, or consequential damages
claimed to arise under the contract of sale.
The emergency equipment manufactured by HAWS is warranted to function if installation
and maintenance instructions provided are adhered to. The units also must be used for the
purpose for which they were intended. This product is intended to supplement first-aid
treatment. Due to widely varying conditions, Haws cannot guarantee that the use of this
emergency equipment will prevent serious injury or the aggravation of existing or prior
injuries.
NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED, PROVIDED
OR GIVEN BY HAWS.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:
Model 8317 Combination
Shower Eye/Face Wash
LIMITED WARRANTY
TECHNICAL SUPPORT: 1-800-766-5612
FOR CUSTOMER SERVICE: 1-888-640-4297
12/12 Model 8317 Page 1 of 5
LOCATION OF UNIT: The Model 8317 Emergency Shower should be installed in
close proximity to potential accident areas. It should be clearly identified, free from
obstructions and easy to access.
SUPPLY LINE: The minimum recommended line size is 1-1/4” IPS with 30-90 psi (2-6
ATM) flowing pressure. Where sediment or mineral content is a problem, an inlet filter
is recommended.
PLUMBING CONNECTIONS: Inlet supply is female 1-1/4” IPS.
INSTALLATION PROCEDURE
Refer to Installation Drawing for clarification. Check parts list to insure all required parts
are included. Use pipe joint sealant PST #565 (Loctite) on all connections.
STEP 1: Prepare the emergency shower foundation by using the floor flange
assembly as a template. Locate the three holes for the 3/8-16 UNC x 6"
anchor bolts (not supplied). They should extend 1" above the floor level.
STEP 2: Once the concrete foundation is ready (dry), assemble the floor flange
assembly to the anchor bolts, then securely fasten with 3/8-16 UNC Hex
Nuts and 3/8" washers (not supplied). Seal and tighten floor flange and (11/4”) coupler. Make sure foot control holes are facing side to side.
STEP 3: Assemble plugged nipple (1-1/4” x 24”) to the floor flange assembly and
tighten with a pipe wrench. (Plugged end up).
STEP 4: Assemble the eyewash assembly and tee (1-1/4” x 1-1/4” x 1/2”) to the
24” nipple from Step three.
STEP 5: Attach nipple (1-1/4" x 31") and tee (1-1/4”) to assembly and tighten.
STEP 6: Attach nipple (1-1/4” x 24”) and tee (1-1/4” x 1-1/4” x 1) and tighten.
STEP 7: Attach nipple (1” x 9”) to valve assembly with a spud wrench.
STEP 8: Assemble the street elbow (1”) onto nipple (1” x 12-1/2”).
Attach nipple onto valve.
Attach the showerhead onto the street elbow (1”).
STEP 9: Assemble the sign onto the unit. Use the strap, screws, washers and nuts
provided, to mount the sign onto the upright. The sign should be
positioned for maximum visibility.
STEP 10: Insert the galvanized plug into the optional supply line tee that is not used.
Before connecting the supply water line to the emergency shower, FLUSH
THE LINE THOROUGHLY.
12/12 Model 8317 Page 2 of 5
TROUBLESHOOTING
PROBLEM
1. No flow. 1. Check the main shut-off valve.
REPAIR CHECKLIST
2. Insufficient water flow, shower and
eyewash.
3. Insufficient water flow on eye/face
wash, however, shower is
sufficient.
4. Eye/face wash stream does not
meet desired eye level.
5. Insufficient water flow at the
showerhead, however, eye/face
wash is sufficient.
2. Verify minimum 30 psi (2 ATM)
flowing supply line pressure.
3. a. Verify minimum 30 psi (2 ATM)
flowing supply line pressure.
b. Probable clogging of flow control
due to inadequate line flushing.
Unscrew eye/face wash head and
remove the four screws to
disassemble the head. Clean flow
control and reassemble head. See
SP65 Installation Drawing for
details.
4. a. Possible blocked flow control, see
above solution.
b. Possible non-leveled eye/face wash
assembly.
5. Probable clogging of flow control
inside shower head. Unscrew
shower head off of elbow and clean
rubber flow control.
6. Water does not drain properly. 6. Check your drain system for debris.
Check the main waste line of your
building to see if it does handle the
capacity required for the entire
drainage system.
7. Water leak between joints or
fittings.
7. Tighten loose connections. If leak
persists, the application of hot water
will sometimes reseat improperly
applied joint compound. After 30
minutes wait and retest, a persistent
leak will necessitate reassembly and
additional sealant.
For more information on Haws Products, please see our website: www.hawsco.com
© 2012 Haws
®
HAWS
12/12 Model 8317 Page 3 of 5
®
Corporation – All Rights Reserved
and other trademarks used in these materials are the exclusive property of Haws Corporation.
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
PARTS BREAKDOWN
DESCRIPTIONITEM
1
SP829 SHOWER HEAD
2 SHOWER VALVE ASSEMBLY
3
-
4 SP200 PULL ROD
5 SP178 SHOWER SIGN
6 SP75 FLOOR FLANGE
7
SP65 EYE/FACE WASH ASSY
89 SP238 VALVE ASSEMBLY
10 SP170 TE ST TAG
11 SP185 STRIPE TAPE
EYE/FACE WASH ASSEMBLY
VALVE ASSEMBLY
BYECN NO.
REVI SED PER
ECN:
4780
DATE
DRAWN
CLF
WHEN ORDERING PARTS PLEASE SPECIFY MODEL NUMBER.
C
2012
Haws Corporation - All Rights Reserved
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
R
APPROVED
03/11/93
DATE
HM
CHKD
MODEL(S)
8317
SHOWER EYE/FACEWASH COMBO
SCALE:
DRAWING TYPE: SIZE: A
1"12.5
PARTS BR EA KDOWN
1455 KLEPPE LANE
SPARKS, NEVADA 89431
(775) 359-4 712 FAX ( 755) 359-7424
E-MAIL: HAWS @ HAW S C O. CO M
WEBSITE: WWW.HAWSCO.COM
PAGE
PART NUMBER
0002080152
DRAWING NO.
11493C00
SHEET OF
11
4 of 5
REV
19
C
Haws Corporation - All Rights Reserved.
2012
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJ ECT TO CHANGE WITHOUT NOTICE.
NOTES:
1. DIMENSIONS MAY VARY BY ± 1/2 INCH [13mm].
2. TO COMPLY WITH ANSI Z358.1-2009 FOR EMERGENCY EYEWASH OR EYE/FACE WASH AND SHOW ER EQUIPMENT:
- UNIT SHALL BE INSTALLED IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS AND ACCEPTABLE PLUMBING PRACTICES.
- EYEWASH OR EYE/FACE WASH SHALL BE POSITI O NED WITH NOZZLES NOT LESS THE N 83.8 CM (33 IN.) AND NO GREATER THAN
114.3 CM (45 IN.) FROM SURFACE ON WHICH USER STANDS AND 15.3 CM (6 IN.) MINIMUM FROM WALL OR NEAREST OBSTRUCTION.
- SHOWER SHALL BE POSITIONED SO THAT SHOW ER H EAD IS NOT LESS THAN 208.3 CM (82 IN.) N O R MORE THAN 243.8 CM (96 IN.)
FROM SURFACE ON WHICH USER STANDS.
- SHOWER SPRAY PATTERN SHALL HAVE A MINI MUM DIAMETER OF 50.8 CM (20 IN.) AT 15 2. 4 CM (60 IN.) ABOVE SURFACE O N WHICH
USER STANDS, AND CENTER OF SPRAY PATTERN SH ALL BE LOCATED AT LEAST 40.6 CM (16 IN. ) FRO M ANY OBSTRUCTION.
3 DO NOT USE REGULAR PIPE SEALANT . IF NEC ESSARY USE DOW CORNING 832 SEALANT PLACING 5 SMALL
BEADS ON THE MALE THREADS, JUST ABOVE THE FIRST THREAD.
2124mm
83 5/8"
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
279mm
11"
1692mm
66 5/8"
FLOOR LINE
3
1086mm
42 3/4"
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
225mm
8 7/8"
660mm
R
26"
4
COUPLING
1-1/4"
1613mm
63 1/2"
4 ORIENT TAB ON EYE/FACEWASH TOWARDS BACK OF SHOWER.
APPROVED:
DRAWN:
C.H.
REVIS ED PER
ECN:
DATE:
05/91
4780
DATE:
CHK'D.:
BY:ECN NO.
HM
SCALE:
MODEL(S)
MOUNTING DETA IL
SHOWER & EYE/FACE WASH CO MBI NATION
1/22
3X 120°
27-1/2"
699mm
EYE/FACE WASH DETAIL
1-1/4" IPS
SUPPLY
DRAWING TYPE: SIZE: A
8317
INSTALLATION
0002080152.D
PART NUMBER
DRAWING NO.
SHEET OF
09553A00 19
11
REV
3X Ø
Ø
229mm
9"
(775) 359-47 12 FAX ( 755) 359-7424
E-MAIL: HAWS@HAWSCO.COM
WEBSI TE: WWW. H AWSCO.COM
SPARKS, NEVADA 89431
1455 KLEPPE LA NE
Ø
203mm
B.C.
8"
9.5mm
3/8"
PAGE
5 of 5
Loading...