Haws 8100 User Manual

)

–

INSTALLATION, OPERATION

&

MAINTENANCE INSTRUCTIONS

1455 Kleppe Lane Sparks, NV 89431-6467 [phone] Fax [phone]

E-mail: [e-mail]  website: www.hawsco.com

NOTE TO INSTALLER: Please leave this information with the Maintenance Department.

HAWS® warrants that all of its products are guaranteed against defective material or poor
workmanship for a period of one year from date of shipment. HAWS liability under this
warranty shall be discharged by furnishing without charge F.O.B. HAWS Factory any
goods, or part thereof, which shall appear to the Company upon inspection to be of
defective material or not of first class workmanship, provided that claim is made in writing
to company within a reasonable period after receipt of the product. Where claims for
defects are made, the defective part or parts shall be delivered to the Company, prepaid,
for inspection. HAWS will not be liable for the cost of repairs, alterations or replacements,
or for any expense connected therewith made by the owner or his agents, except upon
written authority from HAWS, Sparks, Nevada. HAWS will not be liable for any damages
caused by defective materials or poor workmanship, except for replacements, as provided
above. Buyer agrees that Haws has made no other warranties either expressed or implied
in addition to those above stated, except that of title with respect to any of the products or
equipment sold hereunder and that HAWS shall not be liable for general, special, or
consequential damages claimed to arise under the contract of sale.

The emergency equipment manufactured by HAWS is warranted to function if installation
and maintenance instructions provided are adhered to. The units also must be used for
the purpose, which they were intended. This product is intended to supplement first-aid
treatment. Due to widely varying conditions HAWS cannot guarantee that the use of this
emergency equipment will prevent serious injury or the aggravation of existing or prior
injuries.

NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED,
PROVIDED OR GIVEN BY HAWS.

SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL, PLEASE CALL:

FOR PARTS CALL:

(U.S.A. AND CANADA ONLY) MONDAY-THURSDAY: 6:00 A.M. – 4:00 P.M. PST

Model 8100

Drench Shower

LIMITED WARRANTY

1-800-766-5612

1-800-758-9378

FRIDAY: 6:00 A.M

1:00 P.M. PST

No. 2080105 (11

12/09 Model 8100 Page 1 of 5

LOCATION OF UNIT: The Model 8100 Emergency Shower should be installed in close
proximity to potential accident areas. It should be clearly identified, free from obstructions
and easy to access.

SUPPLY LINE: The minimum recommended line size is 1-1/4” NPT with 30-90 psi (2-6
ATM) flowing pressure. Where sediment or mineral content is a problem, an inlet filter is
recommended.

PLUMBING CONNECTIONS: Inlet supply connection is female 1-1/4” NPT.

INSTALLATION PROCEDURE

Refer to Installation Drawing for clarification. Check parts list to insure all required parts are
included. Use pipe joint sealant PST #565 (Loctite) on all connections.

STEP 1: Prepare the emergency shower foundation by using the floor flange assembly as

a template. Locate the three holes for the 3/8-16 UNC x 6” anchor bolts (not
supplied). They should extend 1” above the floor level.

STEP 2: Once the concrete foundation is ready (dry), assemble the floor flange assembly

to the anchor bolts; then securely fasten with 3/8-16 UNC Hex Nuts and 3/8”
washers (not supplied). Seal and tighten floor flange and coupling making certain
the foot control holes are facing side to side.

STEP 3: Assemble nipple (1-1/4” x 33”) to the floor flange assembly and tighten with a pipe

STEP 4: Assemble in the following order:

Attach intermediate coupling to nipple (1-1/4” x 33”)

Attach plugged nipple (1-1/4” x 24”) and tee (1-1/4”) onto the coupling.
Attach nipple (1-1/4” x 24”) onto the tee.
Attach tee (1-1/4” x 1-1/4” x 1”) onto nipple.
Attach nipple (1” x 9”) valve assembly onto tee (1-1/4” x 1-1/4” x 1”)
Assemble the street elbow (1”) onto nipple (1” x 12-1/2”).

Attach nipple onto valve.

STEP 5: Attach the showerhead onto street elbow (1”).

STEP 6: Assemble the sign onto the unit. Use the strap, screws, washers and nuts

STEP 7: Insert the galvanized plug into the optional supply line tee that is not used. Before

wrench.

provided to mount the sign onto the upright. The sign should be positioned for
maximum visibility

connecting the supply water line to the emergency shower, FLUSH THE LINE

THOROUGHLY.

12/09 Model 8100 Page 2 of 5