NO. OOO2076521 (0)
No. 2080102(15)
Model 7777 Stainless Steel
Pedestal Mounted Eye/Face Wash
INSTALLATION, OPERATION
&
MAINTENANCE INSTRUCTIONS
LIMITED WARRANTY
OR GIVEN BY HAWS.
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
1-888-640-4297
1455 Kleppe Lane Sparks, NV 89431-6467 (775) 359-4712 Fax (775) 359-7424
E-mail: haws@hawsco.com website: www.hawsco.com
HAWS warrants that this specific product is guaranteed against defective material or poor
workmanship for a period of one year from date of shipment. HAWS liability under this
warranty shall be discharged by furnishing without charge F.O.B. HAWS Factory any goods,
or part thereof, which shall appear to the Company upon inspection to be of defective
material or not of first class workmanship, pr ovided that claim is made in writing to Haws
within a reasonable period after receipt of the product. Where claims for defects are made,
the defective part or parts shall be delivered to the Company, prepaid, for inspection. HAWS
will not be liable for the cost of repairs, alterations or replacements, or for any expense
connected therewith made by the owner or his agents, except upon written author ity from
HAWS, Sparks, Nevada. HAWS will not be liable for any damages caused by defective
materials or poor workmanship, except for replacements, as provided above. Buyer agrees
that Haws has made no other warranties either expressed or implied in addition to those
above stated, except that of title with respect to any of the products or equipment sold
hereunder and that HAWS shall not be liable for general, special, or consequential damages
claimed to arise under the contract of sale.
The emergency equipment manufactured by HAWS is warranted to function if installation
and maintenance instructions provided are adhered to. The units also must be used for the
purpose for which they were intended. This product is intended to supplement first-aid
treatment. Due to widely varying conditions, Haws cannot guarantee that the use of this
emergency equipment will prevent serious injury or the aggravation of existing or prior
injuries.
NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED, PROVIDED
MODEL PLEASE CALL:
TECHNICAL SUPPORT: 1-800-766-5612
FOR CUSTOMER SERVICE:
08/16 Model 7777 Page 1 of 4
PROBLEM
REPAIR CHECKLIST
1.
flowing supply line pressure.
b.
Probable clogging of flow control
head.
c.
Remove plug located on L –
access and clean filter sc r een.
leveled eye/face was h ass embl y.
drainage system.
LOCATION OF UNIT: The Model 7777 Stainless Steel Pedestal Mounted Eye/Face
Wash should be installed in close proximity to potential accident areas. It should be
clearly identified, free from obstructions and easy to access.
SUPPLY LINE: The minimum recommended line size is 1/2” IPS with 30-90 psi (2-6
ATM) flowing pressure. Where sediment or mineral content is a problem, an inlet filter
is recommended.
PLUMBING CONNECTIONS: Inlet supply is female 1/2” IPS. Waste outlet is female
1-1/4” IPS.
TROUBLESHOOTING
No flow. 1. Check the main shut-off valve.
2. Insufficient water flow.
Eye/face wash streams do not
3.
meet desired eye level.
4. Water does not drain properly.
2. a.
3.
4.
Verify minimum 30psi (2 ATM)
due to inadequate line flushing.
Unscrew eye/face wash head and
remove the four screws to
disassemble head.
Clean flow control and reas se mbl e
Strainer using 9/16” wrench to
Possible blocked flow control , s ee
above solution. Possible non-
Check the main waste line of your
building to see if it does handle the
capacity required for the entire
For more information about Haws products, see our website: www.hawsco.com
© 2016 Haws® Corporation – All Rights Reserved
HAWS® and other trademarks used in these materials are the exclusive property of Haws Corporation.
08/16 Model 7777 Page 2 of 4
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
PARTS BREAKDOWN
OPTIONAL
OPTIONAL
OPTIONAL
DUST COVER SHOWN
IN OPEN POSITION
8
9
ITEM DESCRIPTION
1BOWL
2 SP175 EYEWASH SIGN
3 SP232 VALVE ASSEMBLY
4 SP220SS FOOT TREADLE
5 SP65SS EYE/FACE WASH
6 SP170 TEST TAG
7 SP509SS L-STRAINER
8 9102 DUST COVER ASSEMBLY
9 E/F WASH DUST COVER
--
VRKEWSTR.STR, REPAIR KIT --
PART NO.
SP90
SP175
SP232
SP220SS
SP65SS
SP170
SP509SS
9102
9091
OPTIONAL
1
7
3
5
SP65SS EYE/FACE WASH ASSEMBLY
6
4
2
BYECN NO.
REVISED PER
ECN:
5133
DATE
DRAWN
CLF
WHEN ORDERING PARTS PLEASE SPECIFY MODEL NUMBER.
C
2016
Haws Corporation - All Rights Reserved
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
R
APPROVED
03/04/96
DATE
FV
CHKD
09/01/16
CJC
VWC
MODEL(S)
SCALE:
1/4
SS PED EYE/FACE WASH
7777
DRAWING TYPE: SIZE: A
PARTS BREAKDOWN
1455 KLEPPE LANE
SPARKS, NEVADA 89431
(775) 359- 4712 FAX (775) 359- 7424
E-MAIL: HAWS@HAWSCO.COM
WEBSITE: WWW.HAWSCO.COM
PAGE
PART NUMB ER
0002080102
REVISION
15
SHEET OF
11
3 of 4
C
Haws Corporation - All Rights Reserved.
2016
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
R
AREA SERVED BY THE EYEWASH
THAT IT IS VISIBLE WITHIN THE
SIGN IS TO BE POSITIONE D SUCH
MOUNTING DETAIL
Ø203mm
BC
Ø8"
LINE
FLOOR
Ø10mm
3X
Ø3/8"
OPTIONAL
Ø229mm
Ø9"
SP220SS
4
1016mm
*
MAKE SPECIFICATIO NS AND MEASUREMENTS SUBJECT TO CHANG E W ITHOUT NOTI CE.
THIS DOCUMENT IS TRUE AND CO RRECT AT TI ME OF PUBLI CA T ION. CONT IN UED PRODUCT IMPROVEMENT S
4 DIM APPLIES WHEN OPTI ONAL 9102 DUST COVER
ASSEMBLY IS USED.
- UNIT SHALL BE INSTALLED IN ACCORDANCE WITH
EMERGENCY EYE W ASH OR EYE/FACE WASH AND
SHOWER EQUIPMENT:
2. *DIMENSIONS MAY VARY ±1/2" [12.7mm].
3. CENTERLINE WASTE PLACED 9"[229mm]
MIN. FROM OBSTRUCTION.
SURFACE ON WHI CH USER STANDS AND 15.3 CM (6 IN.)
- EYEWASH OR EYE/FACE WASH SHA LL BE
MANUFACTURER'S INSTRUCTI ONS AND ACCEPTABLE
PLUM BING PRA CTIC ES .
POSITIONED WITH NOZZLES NOT L ESS THEN 83.8 CM (33
IN.) AND NO GREATER THAN 114.3 CM (45 IN.) FROM
MINIMUM FROM WALL OR NE AREST OBSTRUCTION .
NOTES:
1. TO COMPLY WITH AN SI Z358.1-2009 FOR
40"
102mm
FV
09/01/16
SCALE:
1/10
DRAWING TYPE:
APPROVED:
CJL
05/91
DATE:
VWC
SS PED MTD EYE/FACE WASH
DRAWN:
DATE:
CHK'D.:
REVISED PER
ECN:
5133
BY:ECN NO.
CJC
MODEL(S)
171mm
*
6-3/4"
229mm
9" MIN.
826mm
4"
381mm
15"
*
32-1/2"
9102 DUST COVER ASS Y
*
981mm
38-5/8"
SUPPLY
35mm
STRAINER
1/2" IPS
1-3/8"
(OPEN POSITION)
(OPTIONAL)
OBSTRUCTION
7777
INSTALLATION
SIZE: A
0002080102.D
PART NUMBER
REVISION
SHEET OF
11
15
WEBSITE: WWW.HAWSCO.COM
WASTE
1-1/4" IPS
(775) 359-4712 FAX ( 775) 359-7424
E-MA IL : HA W S @ HA W SCO.CO M
SPARKS, NEVA DA 89431
1455 KLEPPE LANE
PAGE
4 of 4
Loading...