Page 1
INSTALLAT IO N, OPE RATION
&
MAINTENANCE INSTRUCTIONS
1455 Kleppe Lane Sparks, NV 89431-6467 (775) 359-4712 Fax (775) 359-7424
E-mail: haws@hawsco.com website: www.hawsco.com
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
HAWS warrants that this specific product is guaranteed against defective material or poor
workmanship for a period of one year from date of shipment. HAWS liability under this
warranty shall be discharged by furnishing without charge F.O.B. HAWS Factory any
goods, or part thereof, which shall appear to the Company upon inspection to be of
defective material or not of first class workmanship, provided that claim is made in writing to
Haws within a reasonable period after receipt of the product. Where claims for defects are
made, the defective part or parts shall be delivered to the Company, prepaid, for inspection.
HAWS will not be liable for the cost of repairs, alterations or replacements, or for any
expense connected therewith made by the owner or his agents, except upon written
authority from HAWS, Sparks, Nevada. HAWS will not be liable for any damages caused by
defective materials or poor workmanship, except for replacements, as provided above.
Buyer agrees that Haws has made no other warranties either expressed or implied in
addition to those above stated, except that of title with respect to any of the products or
equipment sold hereunder and that HAWS shall not be liable for general, special, or
consequential damages claimed to arise under the contract of sale.
The emergency equipment manufactured by HAWS is warranted to function if installation
and maintenance instructions provided are adhered to. The units also must be used for the
purpose for which they were intended. This product is intended to supplement first-aid
treatment. Due to widely varying conditions, Haws cannot guarantee that the use of this
emergency equipment will prevent serious injury or the aggravation of existing or prior
injuries.
NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED, PROVIDED
OR GIVEN BY HAWS.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:
TECHNICAL SUPPORT:
FOR CUSTOMER SERVICE: 1-888-640-4297
Model 7612LH
Eye/Face Wash
LIMITED WARRANTY
1-800-766-5612
No. 2080065(10)
06/15 Model 7612LH Page 1 of 4
Page 2
LOCATION OF UNIT: The Model 7612LH Eye/face wash should be installed in close
proximity to potential accident areas. It should be clearly identified free from
obstructions and easy to access.
SUPPLY LINE: The minimum recommended line size is 1/2" IPS with 30-90 psi (2-6
ATM) pressure. Where sediment or mineral content is a problem, an inlet filter is
recommended.
PLUMBING CONNECTIONS: Inlet supply is 1/2" slip joint. Waste outlet is 1-1/4” NPT.
TROUBLESHOOTING
1. No flow. 1. Check the main shut-off valve.
2. Insufficient water flow. 2. a. Verify minimum 30-PSI flowing
b. Probable clogging of flow control due
3. Eye/face wash streams do not
b. Probable clogging of flow control due
4. Water does not drain properly. 4. Check the main wasteline of your
PROBLEM
meet desired eye level.
3. a. Possible blocked flow control, see
REPAIR CHECKLIST
supply line pressure.
to inadequate line flushing. Unscrew
eye/face wash head and remove the
four screws to disassemble head.
Clean flow control and reassemble
head.
above solution.
to inadequate line flushing. Unscrew
eye/face wash head and remove the
four screws to disassemble head.
Clean flow control and reassemble
head.
building to see if it does handle the
capacity required for the entire
drainage system.
For more information about Haws products, see our website: www.hawsco.com
© 2015 Haws® Corporation – All Rights Reserved
HAWS
06/15 Model 7612LH Page 2 of 4
®
and other trademarks used in these materials are the exclusive property of Haws Corporation.
Page 3
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENT S SUBJECT TO CHANGE WITHOUT NOTICE.
SP65SS EYE/FACE
WASH ASSY.
SP175
EYEWASH SIGN
TEST THIS UNIT EACH WEEK
SP170 TEST TAG
BYECN NO.
REVISED PE R
ECN:
DRAWN
WHEN ORDERING PAR TS PL EASE SPECIFY MOD EL NUMBER.
C
2015
Haws Corporation - All Rights Reserved
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
R
APPROVED
5005
DATE
FV
11/11/96
DATE
FV
CHKD
06/25/15
MODEL(S)
HM
RVH
LEFT HAND DECK MTD EYE/FACE WASH
1:1
SCALE:
DRAWING TYPE: SIZE: A
7612LH
PARTS BREAKDOWN
1455 KLEPPE LANE
SPARKS, NEVADA 89431
(775) 359-4712 FAX (775) 359-7424
E-MAIL: HAWS@HAWSCO.COM
WEBSITE: WWW.HAWSCO.COM
PAGE
PART NUMBER
0002080065
REVISION
10
SHEET OF
11
3 of 4
Page 4
C
Haws Corporation - All Rights Reserved.
2015
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
R
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
2. DIMENSIONS MAY VARY ±1/2" [13mm].
NEAREST OBSTRUCTION.
TO BE 83.8cm (33 IN.) TO 114.3cm (45 IN.) ABOVE THE FLOOR. CENTERLINE OF
EYEWASH HEADS MUST BE 15.2cm (6 IN.) MIN. AWAY FROM WALL OR
NOTES:
1. THE ANSI Z358.1-2009 STANDARD SPECIFIES EYEWASH NOZZLE HEIGHTS
MOUNTING HOLE
DETAIL
22mm
Ø7/8"
1/2" O.D. SUPPLY
2 1/4"
57mm
SWIVEL
FV
06/25/15
SCALE:
1:1
DRAWING TYPE: SIZE: A
INSTALLATION
APPROVED:
C HAYES
3/19/92
DATE:
RVH
LEFT HAND DECK MTD EYE/FACE WASH
DRAWN:
REVISED PER
ECN:
DATE:
5005
BY:ECN NO.
CHK'D.:
HM
MODEL(S)
7612LH
8 1/2"
216mm
(BY OTHERS)
SINK
SILICONE CAULK
SEAL BASE WITH
165.1mm
6-1/2"
229mm
9"
10 1/4"
260mm
381mm
15"
0002080065.D
REVISION
PART NUMBER
SHEET OF
11
10
(775) 359-4712 FAX (775) 359-7424
E-MAIL: HAWS@HAWSCO.COM
WEBSITE: WWW.HAWSCO.COM
SPARKS, NEVADA 89431
1455 KLEPPE LANE
MAX THICK
1 1/8"
29mm
Loading...