Haws 7612LH User Manual

INSTALLATION, OPERATION

&

MAINTENANCE INSTRUCTIONS

1455 Kleppe Lane Sparks, NV 89431-6467 [phone] Fax [phone]

E-mail: [e-mail]  website: www.hawsco.com

NOTE TO INSTALLER: Please leave this information with the Maintenance Department.

HAWS® warrants that all of its products are guaranteed against defective material or poor
workmanship for a period of one year from date of shipment. HAWS liability under this
warranty shall be discharged by furnishing without charge F.O.B. HAWS Factory any
goods, or part thereof, which shall appear to the Company upon inspection to be of
defective material or not of first class workmanship, provided that claim is made in writing to
company within a reasonable period after receipt of the product. Where claims for defects
are made, the defective part or parts shall be delivered to the Company, prepaid, for
inspection. HAWS will not be liable for the cost of repairs, alterations or replacements, or
for any expense connected therewith made by the owner or his agents, except upon written
authority from HAWS, Sparks, Nevada. HAWS will not be liable for any damages caused by
defective materials or poor workmanship, except for replacements, as provided above.
Buyer agrees that Haws has made no other warranties either expressed or implied in
addition to those above stated, except that of title with respect to any of the products or
equipment sold hereunder and that HAWS shall not be liable for general, special, or
consequential damages claimed to arise under the contract of sale.

The emergency equipment manufactured by HAWS is warranted to function if installation
and maintenance instructions provided are adhered to. The units also must be used for the
purpose, which they were intended. This product is intended to supplement first-aid
treatment. Due to widely varying conditions HAWS cannot guarantee that the use of this
emergency equipment will prevent serious injury or the aggravation of existing or prior
injuries.

NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED,
PROVIDED OR GIVEN BY HAWS.

SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:

TECHNICAL SUPPORT:

FOR CUSTOMER SERVICE: 1-888-640-4297

Model 7612LH

Eye/Face Wash

LIMITED WARRANTY

1-800-766-5612

No. 2080065(9)

07/10 Model 7612LH Page 1 of 4

LOCATION OF UNIT: The Model 7612LH Eye/face wash should be installed in close
proximity to potential accident areas. It should be clearly identified free from
obstructions and easy to access.

SUPPLY LINE: The minimum recommended line size is 1/2" IPS with 30-90 psi (2-6
ATM) pressure. Where sediment or mineral content is a problem, an inlet filter is
recommended.

PLUMBING CONNECTIONS: Inlet supply is 1/2" slip joint. Waste outlet is 1-1/4” NPT.

TROUBLESHOOTING

1. No flow. 1. Check the main shut-off valve.

2. Insufficient water flow. 2. a. Verify minimum 30-PSI flowing

b. Probable clogging of flow control due

3. Eye/face wash streams do not

b. Probable clogging of flow control due

4. Water does not drain properly. 4. Check the main wasteline of your

PROBLEM

meet desired eye level.

3. a. Possible blocked flow control, see

REPAIR CHECKLIST

supply line pressure.

to inadequate line flushing. Unscrew
eye/face wash head and remove the
four screws to disassemble head.
Clean flow control and reassemble
head.

above solution.

to inadequate line flushing. Unscrew
eye/face wash head and remove the
four screws to disassemble head.
Clean flow control and reassemble
head.

building to see if it does handle the
capacity required for the entire
drainage system.

For more information about Haws products, see our website: www.hawsco.com

© 2010 Haws® Corporation – All Rights Reserved
HAWS

07/10 Model 7612LH Page 2 of 4

®

and other trademarks used in these materials are the exclusive property of Haws Corporation.