Page 1
Model 7610
Eye/Face Wash
INSTALLATION, OPERATION
&
MAINTENANCE INSTRUCTIONS
No. 2080067(17)
OR GIVEN BY HAWS.
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
1455 Kleppe Lane Sparks, NV 89431-6467 (775) 359-4712 Fax (775) 359-7424
E-mail: haws@hawsco.com website: www.hawsco.com
HAWS warrants that this specific product is guaranteed against defective material or poor
workmanship for a period of one year from date of shipment. HAWS liability under t his
warranty shall be discharged by furnishing without charge F.O.B. HAWS Factory any
goods, or part thereof, which shall appear to the Company upon inspection to be of
defective material or not of first class workmanship, provided that claim is made in writing
to Haws within a reasonable per iod after receipt of the product. W here claims for defects
are made, the defective part or parts shall be delivered to the Company, prepaid, for
inspection. HAWS will not be liable for the cost of repairs, alterations or replacements, or
for any expense connected therewith made by the owner or his agents, except upon
written authority from HAWS, Sparks, Nevada. HAWS will not be liable for any damages
caused by defective materials or poor workmanship, except for replacements, as provided
above. Buyer agrees that Haws has made no other warranties either expressed or implied
in addition to those above stat ed, except that of title with respect to any of the products or
equipment sold hereunder and that HAWS shall not be liable for general, special, or
consequential damages claimed to arise under the contract of sale.
The emergency equipment manufactured by HAWS is warranted to function if installation
and maintenance instructions provided are adhered to. The units also must be used for the
purpose for which they were intended. This product is intended to supplement first-aid
treatment. Due to widely varying conditions, Haws cannot guarantee that the use of this
emergency equipment will prevent serious injury or the aggravation of existing or prior
injuries.
NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED, PROVIDED
MODEL PLEASE CALL:
TECHNICAL SUPPORT: 1-800-766-5612
LIMITED WARRANTY
FOR CUSTOMER SERVICE: 1-888-640-4297
06/17 Model 7610 Page 1 of 7
Page 2
LOCATION OF UNIT: The Model 7610 Eye/Face wash should be installed in close
proximity to potential accident areas. It should be clearly identified, free from
obstructions and easy to access.
SUPPLY LINE: The minimum recommended line size is 1/2" IPS with 30-90 psi (2-6
ATM) pressure. Where sediment or mineral content is a problem, an inlet filter is
recommended.
PLUMBING CONNECTIONS: Inlet supply is 1/2" O.D. slip joint.
INSTALLATION INSTRUCTIONS
NOTES: Instructions apply to both models unless otherwise specified.
Refer to installation drawings to clarify installation procedure.
This product is shipped assembled for use as a 7610 Deck Mounted Eyewash. To
convert to 7610 Wall Mounted Eyewash, follow steps 1 and 2 below and refer to
diagrams on page 6 of 6. Otherwise, skip to Step 3.
STEP 1: Position arm in “Deck Mount Off Position” as shown in Step 1 on page 6 of 6.
STEP 2: Note depth of set screw (referenced during reassembly). Loosen set screw
from cap with 3/32” hex wrench. Rotate eyewash arm 90 degrees clockwise
while making sure to not rotate the spool. Ensure that set screw is aligned
with indent before tightening the set screw in the new arm position. Make sure
the set screw is tight and at its original depth. If the set screw is too shallow ,
this is an indication that it has not properly engaged its indent and the
eyewash will not function properly. Ensure cor r ect arm orient a ti on before
proceeding with installation instructions outlined below. See Page 6 of 6 for
reference drawings.
STEP 3: Remove the 1.25 O.D. flange nut and was her fro m val ve body.
STEP 4: After making sure that the surfaces around the drilled hole are clean and
free of grease, slide valve through drilled hole.
STEP 5: Reinstall the 1.25” O.D. flang e nut and washer. Connect slip joint
connection to complete installation.
STEP 6: Assemble eye/face wash assembly to arm, orient tab on assembly aw ay
from user.
06/17 Model 7610 Page 2 of 7
Page 3
TROUBLESHOOTING
PROBLEM
REPAIR CHECKLIST
1.
No flow.
1. Check the main shut-off valve.
2.
Insufficient water flow.
2.
a.
Verify minimum 30 psi (2 ATM)
flowing supply line pressure.
b.
Probable clogging of flow control due
head.
3.
Eyewash stream does not meet
desired eye level.
3.
a.
Possible blocked flow control , s ee
above solution.
b.
Possible non-leveled e yewash
assembly.
For more information about Haws products, see our website: www.hawsco.com
© 2017 Haws
HAWS
®
and other trademarks used in these materials are the exclusive property of Haws Corporation.
®
Corporation – All Rights Reserved
to inadequate line flushing. Unscrew
eye/face wash head and remove the
four screws to disassemble head.
Clean flow control and reassemble
06/17 Model 7610 Page 3 of 7
Page 4
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
PARTS BREAKDOWN
PULLDOWN EYE/FACE
WASH LABEL
P/N 0003163821
SP65PD
EYE/FACE WASH HEAD
SP175
EYEWASH
SIGN
SP170
TEST TAG
VRK7650
REPAIR KIT
(SEE BELOW)
SPOOL AND SLEEVE
ARE NOT INCLUDED
WITH KIT
VRK7650 REPAIR KIT
INCLUDES:
O-RING (SMALL)
7650 SEAT
O-RING (LARGE)
QTY. 3
QTY. 1
QTY. 1
BYECN NO.
REVISED PER
ECN:
5196
STH
DATE
10/29/96
DATE
FV
DRAWN
WHEN ORDERING PARTS PLEASE SPECIFY MODEL NUMBER.
C
2017
Haws Corporation - All Rights Reserved
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
R
APPROVED
CHKD
07/08/17
MODEL(S)
JP
FV
SCALE:
PULLDOWN EYE/FACE WASH
7610
1:1
DRAWING TYPE: SIZE: A
PARTS BREAKDOWN
1455 KLEPPE LANE
SPARKS, NEVADA 89431
(775) 359-4712 FAX (775) 359-7424
E-MAIL: HAWS@HAWSCO.COM
WEBSITE: WWW.HAWSCO.COM
PAGE
PART NUMBER
0002080067
REVISION
17
SHEET OF
11
4 of 7
Page 5
THIS DOCUMENT IS TRUE AND CORRECT AT TIM E OF PUB L ICATION. CONTINUED PRODUCT IMPROVEME NTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
7"
3-3/4"
178mm
95mm
CAP
3 1/4"
83mm
1-1/2" MAX.
38mm
SINK
(REF.)
3-1/4"
83mm
SET
SCREW
NOTES:
1. WHEN INSTALLING THIS UNIT, LOCAL, STATE, OR FEDERAL CODES SHOULD BE
ADHERED TO FOR INSTALLATION DIMENSIONS (LOCATIONS), WASTE AND SUPPLY
REQUIREMENTS OTHER THAN SHOWN.
3
7610 DECK MOUNTED CONFIGURATION
(SEE SHEET 2 FOR 7610 WALL MOUNTED CONFIGURATION)
(SEE SHEET 3 FOR 7610 DECK MOUNTED DETAIL)
6"
152mm
MIN.
CLEARANCE
Ø3/32"
2.4mm
2"
51mm
ROLL
PIN
ON
POSITION
16-1/2"
419mm
5
2X 0.53"
13.5mm
Ø 7/8"
22mm
FRONT OF SINK
2-3/8"
60mm
OFF
POSITION
LOCKNUT
1/2" O.D.
SUPPLY (COLD)
2X Ø 5/32"
3.18mm
2X 0.53"
13.5mm
5 of 7
PAGE
16-7/8"
429mm
WALL
SEAL BASE WITH
SILICONE CAULK
2. THE ANSI Z358.1-2009 STANDARD SPECIFIES EYEWASH NOZZLE HEIGHTS TO BE
83.8cm (33 IN.) TO 114.3cm (45 IN.) ABOVE THE FLOOR AND 15.3cm (6 IN.) MINIMUM
FROM WALL OR NEAREST OBSTRUCTION.
3 DRILL ONE Ø7/8" [22mm] HOLE AND TWO Ø5/32" HOLES WHERE UNIT IS TO BE
INSTALLED. REFER TO MOUNTING HOLE DETAIL.
4. THESE DIMENSIONS MAY VARY ±1/2" [6.4mm].
5 ASSEMBLE EYE/FACE WASH TO ARM, ORIENT TAB ON ASSEMBLY AWAY FROM USER.
C
2017
Haws Corporation - All Rights Reserved.
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
R
2066
DRAWN:
JF
APPROVED:
FV
3
MOUNTING HOLE DETAIL
ECN:
DATE:
10/96
5196
DATE:
BY:ECN NO.
CHK'D.:
07/08/17
MODEL(S)
JP
FV
SCALE:
PULLDOWN EYE/FACE WASH
1:1
DRAWING TYPE: SIZE: A
REVISED PER
7610
1455 KLEPPE LANE
SPARKS, NEVADA 89431
(775) 359-4712 FAX (775) 359-7424
E-MAIL: HAWS@HAWSCO.COM
WEBSITE: WWW.HAWSCO.COM
INSTALLATION
PART NUMBER
0002080067.D
REVISION
17
SHEET OF
13
Page 6
THIS DOCUMENT IS TRUE AND CORRECT AT TIM E OF PUB L ICATION. CONTINUED PRODUCT IMPROVEME NTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
CONVERT TO
WALL MOUNT CONFIGURATION
STEP 1
BASE
SPOOL
SET
SCREW
DECK MOUNT
OFF POSITION
3-3/4"
95mm
7610 WALL MOUNTED CONFIGURATION
(SEE SHEET 1 FOR 7610 DECK MOUNTED CONFIGURATION)
(SEE SHEET 3 FOR 7610 DECK MOUNTED DETAIL)
16-7/8"
7"
178mm
429mm
WALL
OFF
POSITION
6 of 7
PAGE
UNIT IS SHIPPED IN DECK MOUNT CONFIGURATION. TO
CONVERT TO WALL MOUNT CONFIGURATION, POSITION
ARM IN "DECK MOUNT OFF POSITION" AS ABOVE.
STEP 2
DECK MOUNT
BASE
OFF POSITION
16-1/2"
419mm
1"
25.4mm
WALL MOUNT
SET
OFF POSITION
SCREW
EYEWASH
NOTE DEPTH OF SET SCREW PRIOR TO LOOSENING.
LOOSEN SET SCREW AND ROTATE EYEWASH ARM 90
DEGREES CLOCKWISE (AS SHOWN) WHILE MAKING
SURE TO NOT ROTATE THE SPOOL. RETIGHTEN SET
CONTROL
VALVE
SET
SCREW
SCREW IN NEW POSITION. ENSURE SET SCREW IS
PROPERLY SEATED IN THE INDENT. MAKE SURE THE
SET SCREW IS TIGHT AND AT ITS ORIGINAL DEPTH.
ENSURE CORRECT ARM ORIENTATION BEFORE
MOUNTING TO WALL. REFERENCE DRAWINGS AT RIGHT.
NOTES:
1. WHEN INSTALLING THIS UNIT, LOCAL, STATE, OR FEDERAL CODES SHOULD BE
ADHERED TO FOR INSTALLATION DIMENSIONS (LOCATIONS), WASTE AND SUPPLY
REQUIREMENTS OTHER THAN SHOWN.
CAP
ON
POSITION
33" TO 45"
83.8cm TO 114.3cm
2X 0.53"
13.5mm
Ø 7/8"
22mm
1/2"
12.7mm
5
SEAL BASE WITH
SILICONE CAULK
2X Ø 5/32"
3.18mm
2X 0.53"
13.5mm
1/2" O.D.
SUPPLY
(COLD)
3-1/4"
83mm
1-1/2" MAX.
38mm
FLOOR
LINE
FLOOR
LINE
2. THE ANSI Z358.1-2009 STANDARD SPECIFIES EYEWASH NOZZLE HEIGHTS TO BE
83.8cm (33 IN.) TO 114.3cm (45 IN.) ABOVE THE FLOOR AND 15.3cm (6 IN.) MINIMUM
FROM WALL OR NEAREST OBSTRUCTION.
3 DRILL ONE Ø7/8" [22mm] HOLE AND TWO Ø5/32" HOLES WHERE UNIT IS TO BE
INSTALLED. REFER TO MOUNTING HOLE DETAIL.
4. THESE DIMENSIONS MAY VARY ±1/2" [6.4mm].
5 ASSEMBLE EYE/FACE WASH TO ARM, ORIENT TAB ON ASSEMBLY AWAY FROM USER.
C
2017
Haws Corporation - All Rights Reserved.
3
MOUNTING HOLE DETAIL
1455 KLEPPE LANE
SPARKS, NEVADA 89431
(775) 359-4712 FAX (775) 359-7424
E-MAIL: HAWS@HAWSCO.COM
WEBSITE: WWW.HAWSCO.COM
INSTALLATION
ECN:
DATE:
10/96
5196
DATE:
BY:ECN NO.
CHK'D.:
07/08/17
MODEL(S)
JP
FV
SCALE:
PULLDOWN EYE/FACE WASH
7610
1:1
DRAWING TYPE: SIZE: A
REVISED PER
2066
DRAWN:
JF
APPROVED:
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
R
FV
PART NUMBER
0002080067.D
REVISION
17
SHEET OF
23
Page 7
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
7610 DECK MOUNTED CONFIGURATION
(SEE SHEET 1 FOR 7610 DECK MOUNTED CONFIGURATION)
(SEE SHEET 2 FOR 7610 WALL MOUNTED CONFIGURATION)
SINK
(REFERENCE)
)
m
"
6
(
5
1
E
L
C
m
2
A
R
A
.
N
I
M
E
C
N
ON
DECK MOUNT DETAIL
NOTES:
1. WHEN INSTALLING THIS UNIT, LOCAL, STATE, OR FEDERAL CODES SHOULD BE
ADHERED TO FOR INSTALLATION DIMENSIONS (LOCATIONS), WASTE AND SUPPLY
REQUIREMENTS OTHER THAN SHOWN.
OFF
F
A
N
I
M
R
E
C
2X 0.53"
13.5mm
Ø 7/8"
22mm
W
7 of 7
PAGE
"
5
m
7
2
1
m
C
N
A
R
A
E
L
C
.
S
U
I
D
A
A
S
H
S
F
O
T
R
E
R
S
M
A
E
2X Ø 5/32"
3.18mm
2X 0.53"
13.5mm
FLOOR
LINE
2. THE ANSI Z358.1-2009 STANDARD SPECIFIES EYEWASH NOZZLE HEIGHTS TO BE
83.8cm (33 IN.) TO 114.3cm (45 IN.) ABOVE THE FLOOR AND 15.3cm (6 IN.) MINIMUM
FROM WALL OR NEAREST OBSTRUCTION.
3 DRILL ONE Ø7/8" [22mm] HOLE AND TWO Ø5/32" HOLES WHERE UNIT IS TO BE
INSTALLED. REFER TO MOUNTING HOLE DETAIL.
4. THESE DIMENSIONS MAY VARY ±1/2" [6.4mm].
5 ASSEMBLE EYE/FACE WASH TO ARM, ORIENT TAB ON ASSEMBLY AWAY FROM USER.
C
2017
Haws Corporation - All Rights Reserved.
3
MOUNTING HOLE DETAIL
1455 KLEPPE LANE
SPARKS, NEVADA 89431
(775) 359-4712 FAX (775) 359-7424
E-MAIL: HAWS@HAWSCO.COM
WEBSITE: WWW.HAWSCO.COM
INSTALLATION
ECN:
5196
DATE:
07/07/16
DATE:
BY:ECN NO.
CHK'D.:
07/08/17
MODEL(S)
JP
FV
SCALE:
PULLDOWN EYE/FACE WASH
1:1
DRAWING TYPE: SIZE: A
7610
REVISED PER
5113
DRAWN:
CC
APPROVED:
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
R
FV
PART NUMBER
0002080067.D
REVISION
17
SHEET OF
33
Loading...