Haws 7501, 7501T, 7501T240 Nstallation, Operation & Maintenance Instructions

No. 2080045(16)

Model 7501/7501T/7501T240

Portable Eyewash/Portable Eyewash with Heater

INSTALLATION, OPERATION

&

MAINTENANCE INSTRUCTIONS

LIMITED WARRANTY

, as

NOTE TO INSTALLER: Please leave this information with the Maintenance Department.

SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF

1455 Kleppe Lane Sparks, NV 89431-6467 [phone] Fax [phone]

E-mail: [e-mail]  website: www.hawsco.com

HAWS warrants that this specific product is guaranteed against defective material or poor
workmanship for a period of one year from date of shipment. HAWS liability under this
warranty shall be discharged by furnishing without charge F.O.B. HAWS Factory any
goods, or part thereof, which shall appear to the Company upon inspection to be of
defective material or not of first class workmanship, provided that claim is made in writing
to Haws within a reasonable period after receipt of the product. Where claims for defects
are made, the defective part or parts shall be delivered to the Company, prepaid, for
inspection. HAWS will not be liable for the cost of repairs, alterations or replacements, or
for any expense connected therewith made by the owner or his agents, except upon
written authority from HAWS, Sparks, Nevada. HAWS will not be liable for any damages
caused by defective materials or poor workmanship, except for replacements
provided above. Buyer agrees that Haws has made no other warranties either expressed
or implied in addition to those above stated, except that of title with respect to any of the
products or equipment sold hereunder and that HAWS shall not be liable for general,
special, or consequential damages claimed to arise under the contract of sale.

The emergency equipment manufactured by HAWS is warranted to function if installation
and maintenance instructions provided are adhered to. The units also must be used for
the purpose for which they were intended. This product is intended to supplement first-aid
treatment. Due to widely varying conditions, Haws cannot guarantee that the use of this
emergency equipment will prevent serious injury or the aggravation of existing or prior
injuries

NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED, PROVIDED OR GIVEN BY HAWS.

THIS MODEL PLEASE CALL:

TECHNICAL SUPPORT: 1-800-766-5612

FOR CUSTOMER SERVICE: 1-888-640-4297

.

03/18 Model 7501/7501T/7501T240 Page 1 of 8

CAUTION : A GROUND FAULT DEVICE MUST BE USED WITH THIS HEATING DEVICE.
ATTENTION : CE PRODUIT DOIT ÊTRE UTILISÉ AVEC UNE PROTE CTION DE MISE À LA

TERRE.

RECOMMENDED TOOLS: Three 1/4" diameter anchors suitable for supporting filled eyewash

(approximately 80 pounds), and tools needed to install these anchors.

LOCATION OF UNIT: The Model 7501/7501T/7501T240 eyewash units should be installed in
close proximity to potential accident areas. It should be clearly identified, free from obstructions
and easily accessible. IMPORTANT: Model 7501 eyewash units (non-insulated) shall be

protected from freezing. Models 7501/7501T/7501T240 shall not have internal
temperatures exceeding 38⁰C (100⁰F) and shall not be exposed to ambient temperatures
exceeding 38°C (100°F). Be care ful of direct sunlight.

ELECTRICAL CONNECTIONS: (reference manual supplied with heating blanket)
Model 7501T – 120VAC, 60 Hz, 1.38A. Requires a three-prong o utlet and is supplied with a

heavy-duty 8 foot power cord with GFCI plug. Unit is suitable for installation and use in
NEMA/TYPE 3R areas. Must be used with NEMA/TYPE 3R certified covered outlet (not
supplied). DURING POTENTIAL FREEZING PERIODS INSURE THAT UNIT IS

CONNECTED TO A CONTINUOUS POWER SUPPLY.
Model 7501T240 – 240VAC, 50/60 H z, 0.64A. Requires a 240VAC outlet and is not supplied

with a power cord which must be installed by the user. Unit is suitable for installation and use
in NEMA/TYPE 4 areas. Power connection to be per local code using flexible conduit or cable
rated NEMA/TYPE 4 – no rigid connection permitted. MUST BE PROTECTED BY A Class A
GROUND FAULT CIRCUIT INTERRUPTER (GFCI). DURING POTENTIAL FREEZING

PERIODS INSURE THAT UNIT IS CONNECTED TO A CONTINUOUS POWER SUPPLY.
AMBIENT TEMPERATURE RATINGS:

MODEL 7501: 60°F (16°C) TO 100° (38°C)
MODEL 7501T: -22°F (-30°C) TO 100°F (38°C)
MODEL 7501T240: -30°F (-35°C) TO 100°F (38°C)

03/18 Model 7501/7501T/7501T240 Page 2 of 8

INSTALLATION INSTRUCTIONS

NOTE: Instructions apply to all models unless otherwise specified.

STEP 1: Models 7501T/7501T240: Install the blanket and connect to power source per the

Installation Manual provided with the heating blanket.

CAUTION – DO NOT ENGERIZE THE HEATING BLANKET POWER SOURCE
UNTIL THE EYEWASH IS FILLED WITH FLUSHI NG FL UI D (UP TO FILL LI NE).

NOTICE: MODEL 7501T240 REQUIRES MINIMUM NEMA/TYPE 4 COMPLIANT

EQUIPMENT. ALL POWER CONNECTIONS M UST BE M ADE ACCORDI NG TO
NEC/ CEC CODE USING FLEXIBLE CONDUIT OR CABLE RATED FOR
NEMA/TYPE 4 – NO RIGID CONNECTION PERMITTED.

STEP 2: Model 7501: Mount unit to wall utilizing “J” bracket (supplied). Note: ¼” mounting

hardware not supplied. See Installation Drawing on Page 7 of 8.
Model 7501T/7501T240: Mount eyewash unit to wall utilizing “J” bracket and three

aluminum spacers (supplied). Locate one aluminum spacer behind each bolt hole in
“J” bracket. Note: ¼” mounting hardware is not supplied. See Installation Drawing
on Page 8 of 8.

STEP 3: Make sure portable eyewash unit is level from front to back and left to right before

securing bracket to wall. Eyewash nozzles should be between 33 inches (83.8 cm)
and 53 inches (164.6 cm) above the floor when eyewash arm is in the active

Filled eyewash unit is heavy (approximately 80 pounds). Wall bracket anchors

(lowered) position (See Installation Drawings, pages 7 and 8 of 8).

(Quantity 3 - not supplied) must be strong enough to support the filled eyewash and
the weight of a worker leaning on eyewash.

STEP 4: Fill up to fill line (see important note above). Requires 8.75 gallons (max) of water,

(make sure that no debris or contaminants of any kind are present in the flushing
fluid). Make sure unit is level from front to back and left to right. If installed as
indicated, eyewash unit will provide 15-minute duration of flow.

IMPORTANT – DO NOT FILL PAST WATER FILL LINE AS LEAKAGE WILL
OCCUR AT THE EYEWASH HEADS.

STEP 5: Model 7501T/7501T240: Energize power source and verify operation of heating

blanket. (Refer to heating blanket Operation Manual)

STEP 6: Take proper precautions to help prevent the growth of potentially harmful bacteria in

eyewash tanks. (Refer to Maintenance Instructions)

THE NATIONAL ELECTRICAL CODE REQUIRES GROUND-FAULT EQUIPMENT PROTECTION ON EACH
HEATING CABLE BRANCH CIRCUIT. TO REDUCE THE RISK OF FIRE CAUSED BY DAMAGE OR IMPROPER
INSTALLATION, CIRCUIT BREAKERS SUCH AS SQU ARE D QO-EPD AND QOB-EPD OR EQUIVALENT, WITH
A 30mA TRIP LEVEL, SHOULD BE USED. PLEASE SUBSTITUTE THESE BREAKERS WHEREVER
REFERENCE IS MADE TO CONVENTIONAL BREAKERS IN THIS DOCUMENT. ALTERNATIVE DESIGNS
PROVIDING COMPARABLE LEVELS OF GROUND-FAULT PROTECTION MAY ALSO BE ACCEPTABLE.

03/18 Model 7501/7501T/7501T240 Page 3 of 8

IMPORTANT SAFETY NOTICE