Haws 7461 User Manual

)

IN S T ALLATIO N , OP E RA T ION

NO. OOO2076521 (0

&

MAINTENANCE INSTRUCTIONS

1455 Kleppe Lane Sparks, NV 89431-6467 [phone] Fax [phone]

E-mail: [e-mail] website: www.hawsco.com

NOTE TO INSTALLER: Please leave this information with the Maintenance Department.

HAWS warrants that this specific product is guaranteed against defective material or poor
workmanship for a period of one year from date of shipment. HAWS liability under this
warranty shall be discharged by furnishing without charge F.O.B. HAWS Factory any goods,
or part thereof, which shall appear to the Company upon inspection to be of defective
material or not of first class workmanship, provided that claim is made in writing to Haws
within a reasonable period after receipt of the product. Where claims for defects are made,
the defective part or parts shall be delivered to the Company, prepaid, for inspection. HAWS
will not be liable for the cost of repairs, alterations or replacements, or for any expense
connected therewith made by the owner or his agents, except upon written authority from
HAWS, Sparks, Nevada. HAWS will not be liable for any damages caused by defective
materials or poor workmanship, except for replacements, as provided above. Buyer agrees
that Haws has made no other warranties either expressed or implied in addition to those
above stated, except that of title with respect to any of the products or equipment sold
hereunder and that HAWS shall not be liable for general, special, or consequential damages
claimed to arise under the contract of sale.

The emergency equipment manufactured by HAWS is warranted to function if installation
and maintenance instructions provided are adhered to. The units also must be used for the
purpose for which they were intended. This product is intended to supplement first-aid
treatment. Due to widely varying conditions, Haws cannot guarantee that the use of this
emergency equipment will prevent serious injury or the aggravation of existing or prior
injuries.

NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED, PROVIDED
OR GIVEN BY HAWS.

Pedestal Eye/Face Wash

Model 7361-7461

LIMITED WARRANTY

No 2080056(14)

SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:

TECHNICAL SUPPORT: 1-800-766-5612

04/14 Model 7361-7461 Page 1 of 4

FOR CUSTOMER SERVICE: 1-888-640-4297

LOCATION OF UNIT: The Model 7361/7461 Eyewash should be installed in close

proximity to potential accident areas. It should be clearly identified free from
obstruction and easy to access.

SUPPLY LINE: The minimum recommended line size is 1/2” IPS with 30-90 PSI
(2-6 ATM) pressure. Where sediment or mineral content is a problem, an inlet filter
is recommended.

PLUMBING CONNECTIONS: Inlet supply is female 1/2” IPS. Waste outlet is 1-1/4”
IPS.

TROUBLESHOOTING

PROBLEM

REPAIR CHECKLIST

1. No flow. 1. Check the main shut-off valve.

2. Insufficient water flow. 2. a. Verify minimum 30 psi (2ATM)
flowing supply line pressure.

b. Probable clogging of flow control

due to inadequate line flushing.
Unscrew eye/face wash head and
remove the four screws to
disassemble the head. Clean flow
control and reassemble head. See
SP65 Installation Drawing for
details.

c. Remove cap located on L-Strainer

using a 3/8” allen wrench to access
and clean filter screen.

3. Eyewash or face wash streams

do not meet desired eye level or
are not balanced.

3. Possible blocked flow control or
internal screens, see above
solution. Possible non-leveled
eyewash assembly.

4. Water does not drain properly. 4. Check the main waste line of your
building to see if it does handle the
capacity required for the entire
drainage system.

For more information about Haws products, see our website: www.hawsco.com

© 2014 Haws
HAWS

04/14 Model 7361-7461 Page 2 of 4

®

®

Corporation – All Rights Reserved

and other trademarks used in these materials are the exclusive property of Haws Corporation.