Haws 7460B User Manual

IN S T ALLATIO N , OP E RA T ION

&

MAINTENANCE INSTRUCTIONS

1455 Kleppe Lane Sparks, NV 89431-6467 [phone] Fax [phone]

E-mail: [e-mail] website: www.hawsco.com

NOTE TO INSTALLER: Please leave this information with the Maintenance Department.

HAWS warrants that this specific product is guaranteed against defective material or poor
workmanship for a period of one year from date of shipment. HAWS liability under this
warranty shall be discharged by furnishing without charge F.O.B. HAWS Factory any goods, or
part thereof, which shall appear to the Company upon inspection to be of defective material or
not of first class workmanship, provided that claim is made in writing to Haws within areasonable
period after receipt of the product. Where claims for defects are made, the defective part or parts
shall be delivered to the Company, prepaid, for inspection. HAWS will not be liable for the cost of
repairs, alterations or replacements, or for any expense connected therewith made by the owner
or his agents, except upon written authority from HAWS, Sparks, Nevada. HAWS will not be
liable for any damages caused by defective materials or poor workmanship, except for
replacements, as provided above. Buyer agrees that Haws has made no other warranties either
expressed or implied in addition to those above stated, except that of title with respect to any of
the products or equipment sold hereunder and that HAWS shall not be liable for general, special,
or consequential damages claimed to arise under the contract of sale.

The emergency equipment manufactured by HAWS is warranted to function if installation and
maintenance instructions provided are adhered to. The units also must be used for the purpose
for which they were intended. This product is intended to supplement first-aid treatment. Due to
widely varying conditions, Haws cannot guarantee that the use of this emergency equipment will
prevent serious injury or the aggravation of existing or prior injuries.

NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTH ORIZED, PROVIDED
OR GIVEN BY HAWS.

SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:

TECHNICAL SUPPORT: 1-800-766-5612

FOR CUSTOMER SERVICE: 1-888-640-4297

Model 7360B-7460B/7360BT-7460BT

Eye/Face Wash

LIMITED WARRANTY

No. 2080042(11)

04/14 Model 7360B-7460B/7360BT/7460BT Page 1 of 4

LOCATION OF UNIT: The Model 7360B/7360BT/7460B/7460BT Emergency
Eyewash units should be installed in close proximity to potential accident areas. They
should be clearly identified free from obstructions and easy to access.

SUPPLY LINE: The minimum recommended line size is 1/2" IPS with 30-90 psi (2--6
ATM) pressure. Where sediment or mineral content is a problem, an inlet filter is
recommended.

PLUMBING CONNECTIONS: Inlet supply is female 1/2" IPS. Waste outlet is 1-1/2"
IPS.

TROUBLESHOOTING

PROBLEM

1. No flow. 1.

REPAIR CHECKLIST

Check the main shut-off valve.

2. Insufficient water flow. 2. a. Verify minimum 30 psi (2 ATM)
flowing supply line pressure.

b. Probable clogging of flow control due

to inadequate line flushing. Turn
water supply off. Unscrew eye/face
wash head and remove the four
screws to disassemble head. Clean
flow control and reassemble head.
See SP65 Installation Drawing for
details.

c. Remove cap located on L – Strainer

using a 3/8” allen wrench to access
and clean filter screen.

3. Eyewash or facewash streams do

not meet desired eye level or are
not balanced.

3. Possible blocked flow control, see
above solution. Possible non-leveled
eyewash assembly.

4. Water does not drain properly. 4. Check the main waste line of your
building to see if it does handle the
capacity required for the entire
drainage system.

For more information about Haws products, see our website: www.hawsco.com

© 2014 Haws® Corporation – All Rights Reserved
HAWS

04/14 Model 7360B-7460B/7360BT/7460BT Page 2 of 4

®

and other trademarks used in these materials are the exclusive property of Haws Corporation.