Hatco HDW-1R2 Series General Manual

DRAWER WARMER

HDW-1R2 Series

Installation &

Operating Manual

I & W #07.05.123.00

This manual contains important safety information
concerning the maintenance, use and operation of
this product. Failure to follow the instructions
contained in this manual may result in serious injury.
If you’re unable to understand the contents of this
manual, please bring it to the attention of your
supervisor. Do not operate this equipment unless
you have read and understood the contents of
this manual.

Este manual contiene importante información sobre
seguridad concerniente al mantenimiento, uso
y operación de este producto. Cualquier falla en el
seguimiento de las instrucciones contenidas en este
manual puede resultar en un serio daño. Si usted
no puede entender el contenido de este manual por
favor pregunte a su supervisor. No opere este equipo
al menos que haya leído y comprendido el contenido
de este manual.

CONTENTS

Important Owner Information..................................i

Introduction.................................................................i

Important Safety Instructions ..................................1

Model Description......................................................2

HDW-1R2 Model.................................................2

Specifications..............................................................2

Plug Configuration...............................................2

Electrical Rating Chart.........................................3

Dimensions...........................................................3

Installation..................................................................4

HDW-1R2 Model.................................................4

Location................................................................4

Operation....................................................................5

Food Holding Guide ............................................5

Maintenance ...............................................................6

Cleaning ...............................................................6

Hatco Limited Warranty...........................................7

Authorized Parts Distributors.................Back Cover

IMPORTANT OWNER INFORMATION

Record the model number, serial number, voltage and
purchase date of your Drawer Warmer in the spaces
below. Please have this information available when
calling Hatco for service assistance.

Model No. ____________________________________

Serial No. ____________________________________

Voltage ______________________________________

Date of Purchase ______________________________

Business 8:00 a.m. to 5:00 p.m.
Hours: Central Standard Time

Telephone: [phone]

Fax: [phone] (Parts & Service)

Additional information can be found by visiting our
web site at www.hatcocorp.com

(Summer Hours: June to September –
8:00 a.m. to 5:00 p.m. C.D.T.
Monday through Thursday
8:00 a.m. to 3:30 p.m. C.D.T. Friday)

[phone] (International)

INTRODUCTION

Hatco Drawer Warmers are designed to keep all foods at
optimum serving temperatures without affecting quality.

All Hatco Drawer Warmers are built for tough kitchen
duty with rugged stainless steel construction, heavy-duty
hardware, stainless steel slides and positive-closing
drawers. They keep everything from meat to vegetables
to rolls hot and flavor-fresh until served.

Each drawer features individual controls so you
can hold a wider variety of hot foods during peak
serving periods.

This manual provides the installation, safety and
operating instructions for the Heated Drawer Warmer.
We recommend all installation, operating and safety
instructions appearing in this manual be read prior to
installation or operation of your Hatco Drawer Warmer.

Form No. HDW1R2M-0502

Safety instructions that appear in this manual after
a warning symbol and the words WARNING or

CAUTION printed in bold face are very important.

WARNING means there is the possibility of serious

!

personal injury or death to yourself or others.

CAUTION means there is the possibility of minor

!

or moderate injury. CAUTION without the symbol
signifies the possibility of equipment or property
damage only.

Your Hatco Drawer Warmer is a product of extensive
research and field testing. The materials used were
selected for maximum durability, attractive appearance
and optimum performance. Every unit is thoroughly
inspected and tested prior to shipment.

i

!

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT! Read the following important safety instructions to avoid personal injury or death,
and to avoid damage to the equipment or property.

WARNINGS

Plug unit into a properly grounded electrical
outlet of the correct voltage, size and plug
configuration. If the plug and receptacle do not
match, contact a qualified electrician to determine
the proper voltage and size and install the proper
electrical outlet.

To avoid any injury, turn the power switch off
at the fuse disconnect switch/circuit breaker
or unplug the unit from the power source and
allow to cool completely before performing any
maintenance or cleaning.

For safe and proper operation, the unit must
be located a reasonable distance from combustible
walls and materials. If safe distances are not
maintained, discoloration or combustion
could occur.

To avoid electric shock or personal injury, do not
steam clean or use excessive water on the unit.

If service is required on this unit, contact your
Authorized Hatco Service Agent, or contact the
Hatco Service Department at 800-558-0607 or
414-671-6350; fax [phone] or International
fax [phone].

This product has no “user” serviceable parts.
To avoid damage to the unit or injury to
personnel, use only Authorized Hatco Service
Agents and Genuine Hatco Parts when service
is required.

CAUTIONS

Some exterior surfaces on the unit will get hot.
Use caution when touching these areas to
avoid injury.

The National Sanitation Foundation (NSF)
requires that HDW-1R2 Series units over
36" (91 cm) in length or weighing more than
80 lbs. (36 kg) to be either sealed or raised on the
installation surface. If this unit cannot be sealed at
the point of use, 4" (10 cm) legs are included to
allow for proper cleaning access below unit. See
INSTALLATION instructions for details.

Locate the unit at the proper counter height, in
an area that is convenient for use. The location
should be level to prevent the unit or its contents
from accidentally falling, and strong enough to
support the weight of the unit and food.

To avoid any injury, use caution when opening
drawer. Hot air escapes when drawer is open.

CAUTIONS

Use only non-abrasive cleaners. Abrasive
cleaners could scratch the finish of your unit
marring its appearance and making it susceptible
to soil accumulation.

Do not lay unit on the front or back side or
damage to unit could occur.

Genuine Hatco Replacement Parts are specified
to operate safely in the environments in which
they are used. Some aftermarket or generic
replacement parts do not have the characteristics
that will allow them to operate safely in Hatco
equipment. It is essential to use Hatco
Replacement Parts when repairing Hatco
equipment. Failure to use Hatco Replacement
Parts may subject operators of the equipment to
hazardous electrical voltage, resulting in electrical
shock or burn.

1

Form No. HDW1R2M-0502

MODEL DESCRIPTION

HDW-1R2 MODEL

The HDW-1R2 Model model is a single cavity unit with
two individual drawers designed to keep food products
hot and flavor-fresh until served. The model is
constructed of rugged stainless steel with durable nylon
rollers, 16-gauge stainless steel slides and heavy-duty
hardware. Each drawer features an adjustable
temperature control and temperature monitor. A recessed
on/off switch controls the power for the complete unit.
The insulated top and sides provide maximum
energy efficiency.

SPECIFICATIONS

Figure 1. Model HDW-1R2

PLUG CONFIGURATION

Units are supplied from the factory with an electrical
cord and plug installed. Plugs are supplied according to
the applications as shown in Figure 2.

WARNING
Plug unit into a properly grounded electrical outlet
of the correct voltage, size and plug configuration.
If the plug and receptacle do not match, contact
a qualified electrician to determine the proper
voltage and size and install the proper
electrical outlet.

NEMA 5-15P

Figure 2. Plug Configuration

Form No. HDW1R2M-0502

2