Hatco HDW-1N Owner’s Manual

Register Online!
hatcocorp.com
WARNING
ADVERTENCIA
AVERTISSEMENT
(see page 2)
(voir page 20)
HDW and HDW-B Series/Série
Installation and Operating Manual
Manuel d'installation et d'utilisation
Drawer Warmers
Tiroirs Chauffants
Do not operate this equipment unless you have read and understood the contents of this manual! Failure to follow the instructions contained in this manual may result in serious injury or death. This manual contains important safety information concerning the maintenance, use, and operation of this product. If you’re unable to understand the contents of this manual, please bring it to the attention of your supervisor. Keep this manual in a safe location for future reference.
P/N 07.04.300.00
English = p 2
No opere este equipo al menos que haya leído y comprendido el contenido de este manual! Cualquier falla en el seguimiento de las instrucciones contenidas en este manual puede resultar en un serio lesión o muerte. Este manual contiene importante información sobre seguridad concerniente al mantenimiento, uso y operación de este producto. Si usted no puede entender el contenido de este manual por favor pregunte a su supervisor. Almacenar este manual en una localización segura para la referencia futura.
Ne pas utiliser cet équipement sans avoir lu et compris le contenu de ce manuel ! Le non-respect des instructions contenues dans ce manuel peut entraîner de graves blessures ou la mort. Ce manuel contient des informations importantes concernant l'entretien, l'utilisation et le fonctionnement de ce produit. Si vous ne comprenez pas le contenu de ce manuel, veuillez le signaler à votre supérieur. Conservez ce manuel dans un endroit sûr pour pouvoir vous y référer plus tard.
Français = p 20
© 2016 Hatco Corporation
WARNING
NOTICE
CAUTION
24 Hour 7 Day Parts and Service Assistance available in the United States and Canada by calling 800-558-0607.
CONTENTS
English
Important Owner Information ..............................................2
Introduction...........................................................................2
Important Safety Information...............................................3
Model Description.................................................................4
Model Designation................................................................4
Specifications........................................................................5
Plug Configurations .............................................................5
Electrical Rating Charts .......................................................5
Food Holding Capacity ........................................................9
Dimensions ........................................................................10
Installation...........................................................................12
General ..............................................................................12
Installing HDW-X and HDW-XN Models...............................12
Installing HDW-XB, HDW-XBN, and HDW-XBR Models......13
IMPORTANT OWNER INFORMATION
Record the model number, serial number, voltage, and purchase date of the unit in the spaces below (located on the back of the unit for free-standing units and on the inside of the right panel for built-in units). Please have this information available when calling Hatco for service assistance.
Model No. ________________________________________
Serial No. ________________________________________
Voltage __________________________________________
Operation.............................................................................14
General ..............................................................................14
Food Holding Guide...........................................................14
Maintenance ........................................................................15
General ..............................................................................15
Daily Cleaning....................................................................15
Removing Lime and Mineral Deposits...............................15
Troubleshooting Guide ......................................................16
Options and Accessories...................................................17
Limited Warranty.................................................................19
Authorized Parts Distributors .............................Back Page
Business Hours: 7:00
Telephone: 800-558-0607; 414-671-6350
e-mail: partsandservice@hatcocorp.com
AM to 5:00 PM Central Standard Time (CST)
(Summer Hours: June to September 7:00
AM to 5:00 PM CST Monday–Thursday
7:00
AM to 4:00 PM CST Friday)
Date of Purchase __________________________________
Register your unit!
Completing online warranty registration will prevent delay in obtaining warranty coverage. Access the Hatco website at www.hatcocorp.com, select the Parts & Service pull-down menu, and click on “Warranty Registration”.
INTRODUCTION
Hatco Drawer Warmers are designed to keep foods at optimum serving temperatures without affecting quality. They are built for tough kitchen duty with rugged stainless steel construction, heavy-duty hardware, stainless steel slides, and positive­closing drawers. Drawer Warmers keep everything from meat to vegetables to rolls hot and flavor-fresh until served.
On multiple drawer units, each drawer features individual controls for holding a wider variety of hot foods during peak serving periods.
Hatco Drawer Warmers are products of extensive research and field testing. The materials used were selected for maximum durability, attractive appearance, and optimum performance. Every unit is inspected and tested thoroughly prior to shipment.
This manual provides the installation, safety, and operating instructions for Drawer Warmers. Hatco recommends all installation, operating, and safety instructions appearing in this manual be read prior to installation or operation of the unit.
Additional information can be found by visiting our web site at www.hatcocorp.com.
b
d
tifie
n
e
l is id
a
u
n
is ma
th
s in
r
a
e
p
p
t a
a
th
n
tio
ma
r
fo
ty in
fe
Sa the
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE is used to address practices not related to personal injury.
fol
owi
l
ng s
word panel
gnal
i
:
s
y
2
Form No. HDWM-0716
WARNING
NOTICE
CAUTION
WARNING
English
IMPORTANT SAFETY INSTRUCTIONS
Read the following important safety information before using this equipment to avoid serious injury or death and to avoid damage to equipment or property.
ELECTRIC SHOCK HAZARD:
• Plug unit into a properly grounded electrical receptacle of the correct voltage, size, and plug configuration. If plug and receptacle do not match, contact a qualified electrician to determine and install proper voltage and size electrical receptacle.
• Built-in units must be installed by a qualified electrician. Installation must conform to all local electrical codes. Installation by unqualified personnel will void unit warranty and may lead to electric shock or burn, as well as damage to unit and/or its surroundings.
• Turn OFF power switch, unplug power cord/turn off power at circuit breaker, and allow unit to cool before performing any cleaning, adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not waterproof. Do not operate if unit has been submerged or saturated with water.
• Unit is not weatherproof. Locate unit indoors where ambient air temperature is a minimum of 70°F (21°C).
• Do not clean unit when it is energized or hot.
• Do not steam clean or use excessive water on the unit.
• This unit is not “jet-proof” construction. Do not use jet­clean spray to clean this unit.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged power cord. Cord must be replaced by an Authorized Hatco Service Agent or a person with similar qualifications.
• Do not allow liquids to spill into the unit.
• This unit must be serviced by qualified personnel only. Service by unqualified personnel may lead to electric shock or burn.
• Use only Genuine Hatco Replacement Parts when service is required. Failure to use Genuine Hatco Replacement Parts will void all warranties and may subject operators of the equipment to hazardous electrical voltage, resulting in electrical shock or burn. Genuine Hatco Replacement Parts are specified to operate safely in the environments in which they are used. Some aftermarket or generic replacement parts do not have the characteristics that will allow them to operate safely in Hatco equipment.
FIRE HAZARD:
• Locate unit a minimum of 1″ (25 mm) from combustible walls and materials. If safe distances are not maintained, discoloration or combustion could occur.
• Do not use harsh chemicals such as bleach (or cleaners containing bleach), oven cleaners, or flammable cleaning solutions to clean this unit.
Make sure food product has been heated to the proper food-safe temperature before placing in unit. Failure to heat food product properly may result in serious health risks. This unit is for holding preheated food product only.
Hatco Corporation is not responsible for actual food product serving temperature. It is the responsibility of the user to ensure that food product is held and served at a safe temperature.
Make sure all operators have been instructed on the safe and proper use of the unit.
This unit is not intended for use by children or persons with reduced physical, sensory, or mental capabilities. Ensure proper supervision of children and keep them away from the unit.
This unit has no “user-serviceable” parts. If service is required on this unit, contact an Authorized Hatco Service Agent or contact the Hatco Service Department at 800-558-0607 or 414-671-6350.
BURN HAZARD:
• Some exterior surfaces on unit will get hot. Use caution when touching these areas.
• Use caution when opening drawer. Hot air escapes when drawer is open.
Locate unit in an area that is convenient for use. The location should be level and strong enough to support the weight of the unit and contents.
Do not lay unit on the front or back side. Damage to the unit could occur.
Use non-abrasive cleaners and cloths only. Abrasive cleaners and cloths could scratch finish of unit, marring its appearance and making it susceptible to soil accumulation.
Form No. HDWM-0716
3
Drawer
Vents
Temperature Monitor
POWER ON/OFF (I/O) Switch
TEMPERATURE Control Knob
H D W - X X
Heated
No Character = Freestanding N = Freestanding, Narrow B = Built-In BN = Built-In, Narrow BR = Built-In, Reduced Depth
Drawer Warmer
Quantity of Drawers
MODEL DESCRIPTION
Drawer
Vents
POWER ON/OFF (I/O) Switch
Temperature Monitor
TEMPERATURE Control Knob
English
All Models
All Hatco Drawer Warmers are built of rugged aluminized and stainless steel with durable nylon rollers, 12 gauge stainless steel slides, and heavy-duty hardware. Each drawer features adjustable drawer vents for humidity control, a POWER ON/OFF (I/O) switch, TEMPERATURE control knob, and a TEMPERATURE monitor. Standard size pans 6″ (152 mm) deep are supplied with each drawer. The insulated top and sides provide maximum energy efficiency and the heating elements are warranted for two years.
HDW-X Models
HDW-X Models are freestanding units available in one, two, three, and four-drawer versions. The one, two, and three­drawer units are equipped with 4″ (102 mm) legs. The four-drawer unit is equipped with 6″ (152 mm) stainless steel legs. Freestanding models include an attached 6′ (1829 mm) power cord with plug.
HDW-XN Models
HDW-XN models have all the features of the HDW-X freestanding models but have a narrower profile for smaller space requirements. These units are available in one, two, and three-drawer versions.
HDW-XB Models
HDW-XB Models are built-in units available in one, two, and three-drawer versions. Built-in HDW-XB models include 4′ (1219 mm) of flexible conduit for direct power connection.
HDW-XBN Models
HDW-XBN Models have all the features of the HDW-XB models but have a narrower profile for smaller space requirements. These units are available in one, two, and three-drawer versions.
Model HDW-2
NOTE: Additional caster and leg sizes are available for the
freestanding units. Refer to the OPTIONS AND ACCESSORIES section for details.
MODEL DESIGNATION
Model HDW-2B
HDW-XBR Models
HDW-XBR Models have all the features of the HDW-XB models but have a reduced depth for smaller space requirements. These units are available in one, two, and three-drawer versions.
4
Form No. HDWM-0716
WARNING
NEMA 5-15P
NEMA 5-20P
NEMA 6-15P
CEE 7/7 Schuko
BS-1363
JIS C 8303
English
SPECIFICATIONS
Plug Configurations
Freestanding units are supplied from the factory with an electrical cord and plug installed. Plugs are supplied according to the application.
ELECTRIC SHOCK HAZARD: Plug unit into a properly grounded electrical receptacle of the correct voltage, size, and plug configuration. If plug and receptacle do not match, contact a qualified electrician to determine and install proper voltage and size electrical receptacle.
NOTE: The specification label is located on the back of
freestanding models and the inside left panel of built-in models (remove drawer to view built-in label). See label for serial number and verification of unit electrical information.
NOTE: Receptacle not supplied by Hatco.
Plug Configurations
Electrical Rating Chart — HDW-X Models
Model Voltage Watts Amps Plug Configuration Shipping Weight
HDW-1
HDW-2 100 900 9.0 JIS C 8303 168 lbs. (76 kg)
HDW-3 100 1350 13.5 JIS C 8303 232 lbs. (106 kg)
HDW-4 120 1800 15 NEMA 5-15P 296 lbs. (135 kg)
100 450 4.5 120 450 3.8 NEMA 5-15P 97 lbs. (44 kg)
208 450 2.2 NEMA 6-15P 240 450 1.9 NEMA 6-15P 220 450 2.0 CEE 7/7 Schuko
240 450 1.9 BS-1363 220–230 (CE) 450–492 2.0–2.1 CEE 7/7 Schuko 230–240 (CE) 413–450 1.8–1.9 BS-1363
120 900 7.5 NEMA 5-15P 168 lbs. (76 kg)
208 900 4.3 NEMA 6-15P 168 lbs. (76 kg)
240 900 3.8 NEMA 6-15P 168 lbs. (76 kg)
220 900 4.1 CEE 7/7 Schuko 168 lbs. (76 kg)
240 900 3.8 BS-1363 168 lbs. (76 kg) 220–230 (CE) 900–984 4.1–4.3 CEE 7/7 Schuko 168 lbs. (76 kg)
230-240 (CE) 826–900 3.6–3.8 BS-1363 168 lbs. (76 kg)
120 1350 11.3 NEMA 5-15P 232 lbs. (106 kg)
208 1350 6.5 NEMA 6-15P 232 lbs. (106 kg)
240 1350 5.6 NEMA 6-15P 232 lbs. (106 kg)
220 1350 6.1 CEE 7/7 Schuko 232 lbs. (106 kg)
240 1350 5.6 BS-1363 232 lbs. (106 kg) 220–230 (CE) 1350–1476 6.1–6.4 CEE 7/7 Schuko 232 lbs. (106 kg) 230–240 (CE) 1239–1350 5.4–5.6 BS-1363 232 lbs. (106 kg)
208 1800 8.7 NEMA 6-15P 296 lbs. (135 kg)
240 1800 7.5 NEMA 6-15P 296 lbs. (135 kg)
220 1800 8.2 CEE 7/7 Schuko 296 lbs. (135 kg)
240 1800 7.5 BS-1363 296 lbs. (135 kg) 220–230 (CE) 1800–1968 8.2–8.6 CEE 7/7 Schuko 296 lbs. (135 kg) 230–240 (CE) 1653–1800 7.2–7.5 BS-1363 296 lbs. (135 kg)
JIS C 8303
97 lbs. (44 kg)
97 lbs. (44 kg) 97 lbs. (44 kg) 97 lbs. (44 kg) 97 lbs. (44 kg) 97 lbs. (44 kg) 97 lbs. (44 kg)
The shaded areas contain electrical information for International models only.
NOTE: Shipping weight includes packaging.
Form No. HDWM-0716
5
SPECIFICATIONS
Electrical Rating Chart — HDW-XN Models
Model Voltage Watts Amps Plug Configuration Shipping Weight
HDW-1N 100 450 4.5 JIS C 8303
120 450 3.8 NEMA 5-15P 208 450 2.2 NEMA 6-15P 240 450 1.9 NEMA 6-15P 220 450 2.0 CEE 7/7 Schuko
240 450 1.9 BS-1363 220–230 (CE) 450–492 2.0–2.1 CEE 7/7 Schuko 230–240 (CE) 413–450 1.8–1.9 BS-1363
HDW-2N 100 900 9.0 JIS C 8303 168 lbs. (76 kg)
120 900 7.5 NEMA 5-15P 168 lbs. (76 kg)
208 900 4.3 NEMA 6-15P 168 lbs. (76 kg)
240 900 3.8 NEMA 6-15P 168 lbs. (76 kg)
220 900 4.1 CEE 7/7 Schuko 168 lbs. (76 kg)
240 900 3.8 BS-1363 168 lbs. (76 kg) 220–230 (CE) 900–984 4.1–4.3 CEE 7/7 Schuko 168 lbs. (76 kg) 230–240 (CE) 826–900 3.6–3.8 BS-1363 168 lbs. (76 kg)
HDW-3N 100 1350 13.5 JIS C 8303 232 lbs. (106 kg)
120 1350 11.3 NEMA 5-15P 232 lbs. (106 kg)
208 1350 6.5 NEMA 6-15P 232 lbs. (106 kg)
240 1350 5.6 NEMA 6-15P 232 lbs. (106 kg)
220 1350 6.1 CEE 7/7 Schuko 232 lbs. (106 kg)
240 1350 5.6 BS-1363 232 lbs. (106 kg) 220–230 (CE) 1350–1476 6.1–6.4 CEE 7/7 Schuko 232 lbs. (106 kg) 230–240 (CE) 1239–1350 5.4–5.6 BS-1363 232 lbs. (106 kg)
83 lbs. (38 kg) 83 lbs. (38 kg) 83 lbs. (38 kg) 83 lbs. (38 kg) 83 lbs. (38 kg) 83 lbs. (38 kg) 83 lbs. (38 kg) 83 lbs. (38 kg)
English
6
Form No. HDWM-0716
English
SPECIFICATIONS
Electrical Rating Chart — HDW-XB Models
Model Voltage Watts Amps Plug Configuration Shipping Weight
HDW-1B 120 450 3.8 Hardwired w/Conduit 88 lbs. (40 kg)
208 450 2.2 Hardwired w/Conduit 88 lbs. (40 kg) 240 450 1.9 Hardwired w/Conduit 88 lbs. (40 kg) 220 450 2.0 Hardwired w/Conduit 88 lbs. (40 kg)
240 450 1.9 Hardwired w/Conduit 88 lbs. (40 kg) 220–230 (CE) 450–492 2.0–2.1 Hardwired w/Conduit 88 lbs. (40 kg) 230–240 (CE) 413–450 1.8–1.9 Hardwired w/Conduit 88 lbs. (40 kg)
HDW-2B 120 900 7.5 Hardwired w/Conduit 159 lbs. (72 kg)
208 900 4.3 Hardwired w/Conduit 159 lbs. (72 kg)
240 900 3.8 Hardwired w/Conduit 159 lbs. (72 kg)
220 900 4.1 Hardwired w/Conduit 159 lbs. (72 kg)
240 900 3.8 Hardwired w/Conduit 159 lbs. (72 kg) 220–230 (CE) 900–984 4.1–4.3 Hardwired w/Conduit 159 lbs. (72 kg) 230–240 (CE) 826–900 3.6–3.8 Hardwired w/Conduit 159 lbs. (72 kg)
HDW-3B 120 1350 11.3 Hardwired w/Conduit 232 lbs. (105 kg)
208 1350 6.5 Hardwired w/Conduit 232 lbs. (105 kg)
240 1350 5.6 Hardwired w/Conduit 232 lbs. (105 kg)
220 1350 6.1 Hardwired w/Conduit 232 lbs. (105 kg)
240 1350 5.6 Hardwired w/Conduit 232 lbs. (105 kg) 220–230 (CE) 1350–1476 6.1–6.4 Hardwired w/Conduit 232 lbs. (105 kg) 230–240 (CE) 1239–1350 5.4–5.6 Hardwired w/Conduit 232 lbs. (105 kg)
The shaded areas contain electrical information for International models only.
NOTE: Shipping weight includes packaging.
Form No. HDWM-0716
7
SPECIFICATIONS
English
Electrical Rating Chart — HDW-XBN Models
Model Voltage Watts Amps Plug Configuration Shipping Weight
HDW-1BN 120 450 3.8 Hardwired w/Conduit 88 lbs. (40 kg)
208 450 2.2 Hardwired w/Conduit 88 lbs. (40 kg) 240 450 1.9 Hardwired w/Conduit 88 lbs. (40 kg) 220 450 2.0 Hardwired w/Conduit 88 lbs. (40 kg)
240 450 1.9 Hardwired w/Conduit 88 lbs. (40 kg) 220–230 (CE) 450–492 2.0–2.1 Hardwired w/Conduit 88 lbs. (40 kg) 230–240 (CE) 413–450 1.8–1.9 Hardwired w/Conduit 88 lbs. (40 kg)
HDW-2BN 120 900 7.5 Hardwired w/Conduit 159 lbs. (72 kg)
208 900 4.3 Hardwired w/Conduit 159 lbs. (72 kg)
240 900 3.8 Hardwired w/Conduit 159 lbs. (72 kg)
220 900 4.1 Hardwired w/Conduit 159 lbs. (72 kg)
240 900 3.8 Hardwired w/Conduit 159 lbs. (72 kg) 220–230 (CE) 900–984 4.1–4.3 Hardwired w/Conduit 159 lbs. (72 kg) 230–240 (CE) 826–900 3.6–3.8 Hardwired w/Conduit 159 lbs. (72 kg)
HDW-3BN 120 1350 11.3 Hardwired w/Conduit 223 lbs. (101 kg)
208 1350 6.5 Hardwired w/Conduit 223 lbs. (101 kg)
240 1350 5.6 Hardwired w/Conduit 223 lbs. (101 kg)
220 1350 6.1 Hardwired w/Conduit 223 lbs. (101 kg)
240 1350 5.6 Hardwired w/Conduit 223 lbs. (101 kg) 220–230 (CE) 1350–1476 6.1–6.4 Hardwired w/Conduit 223 lbs. (101 kg) 230–240 (CE) 1239–1350 5.4–5.6 Hardwired w/Conduit 223 lbs. (101 kg)
The shaded areas contain electrical information for International models only.
NOTE: Shipping weight includes packaging.
8
Form No. HDWM-0716
English
SPECIFICATIONS
Electrical Rating Chart — HDW-XBR Models
Model Voltage Watts Amps Plug Configuration Shipping Weight
HDW-1BR
HDW-2BR 120 900 7.5 NEMA 5-15P 168 lbs. (76 kg)
HDW-3BR 120 1350 11.3 NEMA 5-15P 232 lbs. (106 kg)
120 450 3.8 NEMA 5-15P 80 lbs. (36 kg) 208 450 2.2 NEMA 6-15P
240 450 1.9 NEMA 6-15P 220 450 2.0 CEE 7/7 Schuko
240 450 1.9 BS-1363 220–230 (CE) 450–492 2.0–2.1 CEE 7/7 Schuko 230–240 (CE) 413–450 1.8–1.9 BS-1363
208 900 4.3 NEMA 6-15P 168 lbs. (76 kg)
240 900 3.8 NEMA 6-15P 168 lbs. (76 kg)
220 900 4.1 CEE 7/7 Schuko 168 lbs. (76 kg)
240 900 3.8 BS-1363 168 lbs. (76 kg) 220–230 (CE) 900–984 4.1–4.3 CEE 7/7 Schuko 168 lbs. (76 kg)
230-240 (CE) 826–900 3.6–3.8 BS-1363 168 lbs. (76 kg)
208 1350 6.5 NEMA 6-15P 232 lbs. (106 kg)
240 1350 5.6 NEMA 6-15P 232 lbs. (106 kg)
220 1350 6.1 CEE 7/7 Schuko 232 lbs. (106 kg)
240 1350 5.6 BS-1363 232 lbs. (106 kg) 220–230 (CE) 1350–1476 6.1–6.4 CEE 7/7 Schuko 232 lbs. (106 kg) 230–240 (CE) 1239–1350 5.4–5.6 BS-1363 232 lbs. (106 kg)
80 lbs. (36 kg) 80 lbs. (36 kg) 80 lbs. (36 kg) 80 lbs. (36 kg) 80 lbs. (36 kg) 80 lbs. (36 kg)
The shaded areas contain electrical information for International models only.
NOTE: Shipping weight includes packaging.
Food Holding Capacity
A standard drawer has the following capacity:
Dinner Rolls: 6–8 dozen Ribs: 25–30 lbs. (11–14 kg) Potatoes: 3–3-1/2 dozen
Form No. HDWM-0716
9
SPECIFICATIONS
A B
D E
C
Front View Side View
A
B
C
D
E
Front View
Side View
Dimensions — HDW-X and HDW-XN Models
English
Width
Model
HDW-1 29-1/2
HDW-2 29-1/2
HDW-3 29-1/2
HDW-4 29-1/2
HDW-1N 20-7/8
HDW-2N 20-7/8
HDW-3N 20-7/8
* Height (C) includes 4" (102 mm) legs for 1–3 drawer models and 6" (152 mm) legs for 4 drawer models.
Refer to the OPTIONS AND ACCESSORIES section for Height (C) with optional casters.
Add 1-3/8" (35 mm) to Depth (B) to include the drawer handle.
(A)
''
(749 mm)
''
(749 mm)
''
(749 mm)
''
(749 mm)
''
(530 mm)
''
(530 mm)
''
(530 mm)
Depth
(B) †
''
22-5/8
(575 mm)
''
22-5/8
(575 mm)
''
22-5/8
(575 mm)
''
22-5/8
(575 mm)
''
27
(686 mm)
''
27
(686 mm)
''
27
(686 mm)
Height
(C) *
35-1/4
47-3/8
35-1/4
''
''
''
''
''
''
''
15-1/16
(381 mm)
25-3/16
(639 mm)
(896 mm)
(1203 mm)
15-1/16
(381 mm)
25-3/16
(639 mm)
(896 mm)
Footprint Width (D)
''
24-3/4
(629 mm)
''
24-3/4
(629 mm)
''
24-3/4
(629 mm)
''
24-3/4
(629 mm)
''
16-1/8
(408 mm)
''
16-1/8
(408 mm)
''
16-1/8
(408 mm)
Dimensions — HDW-XB and HDW-XBN Models
Width
Model
HDW-1B 29-1/4
HDW-2B 29-1/4
HDW-3B 29-1/4
HDW-1BN 20-9/16
HDW-2BN 20-9/16
HDW-3BN 20-9/16
(A)
(743 mm)
(743 mm)
(743 mm)
(523 mm)
(523 mm)
(523 mm)
''
''
''
''
''
''
Depth
(B) †
''
22-3/8
(568 mm)
''
22-3/8
(568 mm)
''
22-3/8
(568 mm)
''
26-3/4
(680 mm)
''
26-3/4
(680 mm)
''
26-3/4
(680 mm)
Height
(C)
''
10-7/8
(276 mm)
''
21
(534 mm)
''
31-1/8
(791 mm)
''
10-7/8
(276 mm)
''
21
(534 mm)
''
31-1/8
(791 mm)
Built-In
Width (D)
19-1/2
19-1/2
19-1/2
''
''
''
''
''
''
28-3/16
(715 mm)
28-3/16
(715 mm)
28-3/16
(715 mm)
(494 mm)
(494 mm)
(494 mm)
Footprint Depth (E)
19-1/16
(484 mm)
19-1/16
(484 mm)
19-1/16
(484 mm)
19-1/16
(484 mm)
23-7/16
(594 mm)
23-7/16
(594 mm)
23-7/16
(594 mm)
''
''
''
''
''
''
''
Built-In
Height (E)
30
30
''
''
''
''
9-13/16
(248 mm) 19-15/16
(506 mm)
(763 mm)
9-13/16
(248 mm) 19-15/16
(506 mm)
(763 mm)
''
''
Add 1-3/8" (35 mm) to Depth (B) to include the conduit connector.
Add 1-3/8" (35 mm) to Depth (B) to include the drawer handle.
HDW-X and HDW-XN Dimensions
10
HDW-XB and HDW-XBN Dimensions
Form No. HDWM-0716
English
A
B
C
D
E
Front View
Side View
Dimensions — HDW-XBR
SPECIFICATIONS
Width
Model
HDW-1BR 29-1/8
HDW-2BR 29-1/8
HDW-3BR 29-1/8
Add 1-3/8" (35 mm) to Depth (B) to include the conduit connector.
Add 1-3/8" (35 mm) to Depth (B) to include the drawer handle.
HDW-XBR Dimensions
(A)
''
(740 mm)
''
(740 mm)
''
(740 mm)
Depth
(B) †
''
16-1/2
(418 mm)
''
16-1/2
(418 mm)
''
16-1/2
(418 mm)
Height
(C)
''
10-3/4
(273 mm)
''
21-1/2
(546 mm)
''
32-1/4
(819 mm)
Built-In
Width (D)
28-3/16
(715 mm)
28-3/16
(715 mm)
28-3/16
(715 mm)
''
''
''
Built-In
Height (E)
''
9-3/4
(248 mm)
''
20-1/2
(521 mm)
''
31-1/4
(794 mm)
Form No. HDWM-0716
11
INSTALLATION
NOTICE
WARNING
Caster Plate
Bolt
Lengthen
Shorten
Adjustable Tip
English
General
Hatco Drawer Warmers are shipped with most components pre­assembled. Care should be taken when unpacking the shipping carton to avoid damage to the unit and components enclosed.
ELECTRIC SHOCK HAZARD: Unit is not weatherproof. Locate unit indoors where ambient air temperature is a minimum of 70°F (21°C).
FIRE HAZARD: Locate unit a minimum of 1″ (25 mm) from combustible walls and materials. If safe distances are not maintained, combustion or discoloration could occur.
Do not lay unit on the front or back side. Damage to the unit could occur.
1. Remove the unit from the carton.
NOTE: To prevent delay in obtaining warranty coverage,
complete online warranty registration. See the IMPORTANT OWNER INFORMATION section for details.
2. Remove tape and protective packaging from all surfaces of unit.
3. Place the unit in the desired location.
• Locate the unit in an area where the ambient air temperature is constant and a minimum of 70°F (21°C). Avoid areas that may be subject to active air movements or currents (i.e., near exhaust fans/hoods and air conditioning ducts).
• Make sure the unit is located on solid, level flooring or in sturdy cabinetry.
• Make sure the unit is at the proper height in an area convenient for use.
4. Install the unit. Refer to the appropriate installation procedure in this section.
Installing HDW-X and HDW-XN Models
HDW-X and HDW-XN models are freestanding units that require the installation of 4″ (102 mm) legs or casters before operation.
1. Remove the plastic bag containing the four legs or casters from the drawer of the unit.
2. Carefully lay the unit on its side (requires two people).
3. Install each leg or caster. Refer to the appropriate procedure in this section.
4. Return the unit to its upright position (requires two people). For units on legs — If the unit is not level or rocks, turn the adjustable tip of the appropriate leg to level the unit.
Installing Legs
1. Thread a leg into the hole located at one corner of the unit.
2. Hand-tighten the leg until snug. Do not over-tighten.
3. Repeat steps 1 and 2 for the remaining three legs.
Leg Installation on HDW-2 Model
Installing Casters
1. Align the four holes on the caster plate with the four holes in the bottom of the unit at one corner of the unit.
2. Install a bolt through each of the holes in the caster plate and into the bottom of the unit. Tighten securely.
3. Repeat steps 1 and 2 for the remaining three casters.
12
Caster Installation on HDW-3 Model
Form No. HDWM-0716
Loading...
+ 28 hidden pages