HASBRO Play Doh Creations 3D Flash Art User Manual

AGES

needed to insert batteries.

5+

18531

3D Flash Art

CONTENTS:

3D FLASH ART, plastic blister, 3 paint bottles, 4 design
cards, 5 Bend and Build Sticks, and 4 one-ounce cans of
PLAY-DOH® Brand Modeling Compound.

COMPOUND NET WT. 4 OZ. (123 g)

PAINT NET WT. 2.11 FLUID OZ. (62 ml)

™

ALKALINE

x4

1.5V C or LR14 size

NOT INCLUDED

Phillips/cross head screwdriver (not included)

BATTERIES
REQUIRED

Stain Advisement: Note that paint may stain
some surfaces. Wash with soap and warm water.

BASICS:

Manually shuffle
through the different
strobe patterns

Automatic strobe
start/stop

There are all kinds of amazing designs you can make with the 3D FLASH ART toy. When
you’re ready to spin your designs, turn off the lights to get the full glowing effect!

On/Off

CREATING DESIGNS WITH PAINT:

1. Secure a design card onto the spinner platform

as shown. Make sure all four corners are secure.

3. Drip paint onto the spinning design card. You

can drip two paints at once for a different effect.

Try putting paint on your design
card before placing it on the
spinner platform.

2. Press to start the

spinning action!

4. Once the

paint has dried
on your design
card, you can
stand the 3D
FLASH ART toy
upright and put
it on display!

You can also frame or hang
your dry design cards.

CREATING DESIGNS WITH PLAY-DOH®COMPOUND:

1. Fill blister with compound.

2. Secure it to the spinner platform as shown.

Make sure both edges are secure under lip of
spinner platform.

Tip: Insert the bigger edge first, then the smaller edge.

3. Press once to start the spinning action!

CREATING DESIGNS WITH BEND AND BUILD STICKS:

Your Bend and Build sticks will stick to the design cards, spinner platform
and blister. Be sure to stick the whole Bend and Build Stick to the surface.

For the coolest effect, keep parts
of your bendy sticks raised.

When a Bend and Build Stick starts to lose its stickiness,
throw it away. Don’t use wet paint with these sticks.

Look for more BEND AND BUILD STICKS
and PLAY-DOH COMPOUND!

FUN IDEAS:

You can use a combination of PLAY-DOH compound, Bend and Build Sticks and painted
design cards on your spinner. Be sure the paint has dried on your design cards before adding
compound or sticks.

CLEANING UP:

Turn off the 3D FLASH ART toy and wipe with a damp paper towel to clean and
prevent paint build-up.

TROUBLESHOOTING:

If the toy doesn’t respond, change the batteries.

TO INSTALL BATTERIES:

Use a Philips/cross head screwdriver
(not included) to loosen screw in battery
compartment cover (screw remains
attached to door). Insert 4 x 1.5V “C” or
LR14 size alkaline batteries. Replace cover
and tighten screw.

IMPORTANT: BATTERY INFORMATION

CAUTION:

1. Always follow the instructions carefully. Use only batteries specified and be sure to insert
them correctly by matching the + and – polarity markings.

2. Do not mix old batteries and new batteries or standard (carbon-zinc) with alkaline batteries.

3. Remove exhausted or dead batteries from the product.

4. Remove batteries if product is not to be played with for a long time.

5. Do not short-circuit the supply terminals.

6. Should this product cause, or be affected by, local electrical interference, move it away
from other electrical equipment. Reset (switching off and back on again or removing
and re-inserting batteries) if necessary.

7. RECHARGEABLE BATTERIES: Do not mix these with any other types of batteries. Always
remove from the product before recharging. Recharge batteries under adult supervision.

DO NOT RECHARGE OTHER TYPES OF BATTERIES.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Consult the dealer or an experienced radio/T V technician for help.

CAUTION: Changes or modifications to this unit not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

PLAY-DOH and the PLAY-DOH logo are trademarks identifying quality modeling compound products produced

exclusively by Hasbro, Inc.

© 2010 Hasbro. All Rights Reserved.

denote U.S. Trademarks.

TM &

®

U.S. Patent No. 6713624.
18531

P/N 7069670000

NOTICE TO PARENTS: CONTAINS WHEAT.

NONTOXIC. CONFORMS TO ASTM D-4236.