Hartell LTP-1 801284, LTS-1 801285 Installation Manual

	Item	Qty	Part #	Description
			630092	Motor LTS-1, 115 VAC, 1/3 hp
	1	1
			630090	Motor LTP-1, 115 VAC, 1/4 hp
	2	1	620172 L-211S	SJE Switch Float Assembly w/Gasket (2000 to present)
	3	1	640087 P-107	Impeller Shaft Seal
			630057 PS-103	Impeller with Set Screw, LTS
	4	1
			650030 PA-103	Impeller with Set Screw, LTP
			640089 PS-106	Impeller Shaft with Sleeve
	5	1
			640069 PA-106	Impeller Shaft with Sleeve
	6	1	620155 P115	Gasket Set (Perimeter Seal, Switch & Impeller Seals)
	7	1	640095 P-100	Tank Cover
	8	1	640096 P-112	Tank
	9	1	200500 P-104	Impeller Chamber Cover

Keep these sheets with the pump. They may be valuable if service is needed under the terms of the warranty.

Model #: _______________________ Date of installation: ______________

Installer: ________________________ Date Code: ____________________

Dealer: _________________________

Literature # 900917 2019

100 East Graham Place Burbank, CA 91502 Web: www.hartell.com Email: [e-mail]

MODEL LTP-1 801284 & LTS-1 801285

WASTE WATER REMOVAL PUMP

INSTALLATION • OPERATION • MAINTENANCE

NTRODUCTION

HARTELL LTS and LTP are general-purpose reservoir pumps developed for laundry and wet bar applications. These models are utilized to pump wastewater from an area with no floor drains to an overhead or remote drain line. The pump must be installed in conjunction with a (laundry) tub/ sink. This pump has been carefully engineered to provide long, trouble free service and is of the highest quality workmanship and materials.

These pumps have been thoroughly inspected and tested, then carefully packaged to insure safe delivery and operation. When you receive your pump, examine it carefully to determine that there are no damaged or broken parts. If damage is detected, notify the firm from where the pump was purchased. They will assist with a repair or replacement.

See the precautions listed below before continuing.

CAUTION: READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION

-Pump should only be used with liquids compatible with pump component materials. Do not use to pump flammable or explosive fluids. Do not use in explosive atmospheres.

-The pump is supplied with a grounding type plug. To reduce the risk of electrical shock be certain that it is connected to a properly grounded, grounding receptacle.

-Do not handle pump with wet hands or when standing on a wet or damp surface, or in water.

-Shut off the electrical power at the fuse box before making any connections. All wiring must comply with local codes.

-A strainer must be installed in the tub to prevent foreign objects, (buttons, screws, etc.), from entering and damaging the pump. In laundry applications a lint trap must be installed to prevent an excessive build-up of lint that could interfere with proper float/switch and impeller operation. A nylon stocking works well as a lint trap.

-Applying heat directly to the tank with a torch, or indirectly by heat transfer through copper tubing can melt the tank. This will void the warranty. Solder fittings and tubing first, allow to cool, and then assemble to the tank. The use of some pipe dopes will soften and/or crack the plastic used in this pump. This will void the warranty. Use only Teflon tape when installing threaded fittings to the tank.

ONE YEAR LIMITED WARRANTY

HARTELL LTP and LTS waste water pumps are guaranteed to be free from defects in workmanship or materials and to function satisfactorily, when properly installed, for a period of ONE (1) year from date of installation. HARTELL will replace, without charge, any HARTELL product found to be defective upon examination at our factory if returned within the guarantee period, transportation charges prepaid.

This guarantee does not apply if the product has been misapplied or mechanically damaged, HARTELL assumes no liability for resultant damages of any kind arising out of the use of its products.