Table of Contents
Safety ......................................................... 2
Specifications ............................................. 8
Setup .......................................................... 9
SAFETY OPERATION MAINTENANCESETUP
Operation ................................................... 10
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Maintenance .............................................. 11
Parts List and Diagram .............................. 14
Warranty .................................................... 16
WARNING SYMBOLS AND DEFINITIONS
Obey all safety messages that follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
IMPORTANT SAFETY INFORMATION
General Power Tool Safety Warnings
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term ″power tool″ in the warnings refers to your mains-operated (corded) power tool.
Work area safety
1. Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
Page 2 For technical questions, please call 1-800-444-3353. Item 69820
3. Keep children and bystanders
away while operating a power tool.
Distractions can cause you to lose control.
Electrical safety
1. Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with grounded
power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
2. Avoid body contact with grounded surfaces
such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is grounded.
3. Do not expose power tools to rain or wet
conditions. Water entering a power tool
will increase the risk of electric shock.
Personal safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the influence of drugs, alcohol or
medication. A moment of inattention while operating
power tools may result in serious personal injury.
2. Use personal protective equipment. Always wear
eye protection. Safety equipment such as
dust mask, non-skid safety shoes, hard hat,
or hearing protection used for appropriate
conditions will reduce personal injuries.
3. Prevent unintentional starting. Ensure the Trigger
is in the off-position before connecting to
power source, picking up or carrying the tool.
Carrying power tools with your finger on
the Trigger or energizing power tools that
have the Trigger on invites accidents.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled
cords increase the risk of electric shock.
5. When operating a power tool outdoors,
use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor
use reduces the risk of electric shock.
6. If operating a power tool in a damp location
is unavoidable, use a Ground Fault Circuit
Interrupter (GFCI) protected supply.
Use of a GFCI reduces the risk of electric shock.
4. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
5. Dress properly. Do not wear loose clothing or
jewelry. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewelry
or long hair can be caught in moving parts.
6. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
these devices can reduce dust-related hazards.
7. Only use safety equipment that has been
approved by an appropriate standards agency.
Unapproved safety equipment may not provide
adequate protection. Eye protection must be
ANSI-approved and breathing protection
must be NIOSH-approved for the
specific hazards in the work area.
SAFETYOPERATIONMAINTENANCE SETUP
Power tool use and care
1. Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job better and
safer at the rate for which it was designed.
2. Do not use the power tool if the Trigger
does not turn it on and off.
Any power tool that cannot be controlled with the
Trigger is dangerous and must be repaired.
3. Disconnect the plug from the power source
before making any adjustments, changing
accessories, or storing power tools.
Such preventive safety measures reduce the
risk of starting the power tool accidentally.
4. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
5. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
6. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
Page 3For technical questions, please call 1-800-444-3353.Item 69820
7. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
SAFETY OPERATION MAINTENANCESETUP
Service
Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
Belt and Non-disc Sander Safety Warnings
1. Hold power tools by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a ″live″ wire will make exposed metal
parts of the tool ″live″ and shock the operator.
2. Maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
3. Avoid unintentional starting.
Prepare to begin work before turning on the tool.
4. Do not lay the tool down until it has come to
a complete stop. Moving parts can grab the
surface and pull the tool out of your control.
5. When using a handheld power tool,
maintain a firm grip on the tool with both
hands to resist starting torque.
6. Do not leave the tool unattended when it is plugged
into an electrical outlet. Turn off the tool, and
unplug it from its electrical outlet before leaving.
• Properly maintain and inspect to avoid
electrical shock.
• Properly ground power cord. Ground Fault Circuit
Interrupter (GFCI) should also be implemented
– it prevents sustained electrical shock.
9. WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities, contains chemicals known [to the State
of California] to cause cancer, birth defects or
other reproductive harm. Some examples of
these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement or
other masonry products
• Arsenic and chromium from
chemically treated lumber
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
filter out microscopic particles.
(California Health & Safety Code § 25249.5, et seq.)
7. This product is not a toy.
Keep it out of reach of children.
8. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
In addition, people with pacemakers should:
• Avoid operating alone.
• Do not use with Trigger locked on.
10. WARNING: Handling the cord on this product will
expose you to lead, a chemical known to the State of
California to cause cancer, and birth defects or other
reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)
11. The warnings, precautions, and instructions
discussed in this instruction manual cannot cover all
possible conditions and situations that may occur.
It must be understood by the operator that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the operator.
Page 4 For technical questions, please call 1-800-444-3353. Item 69820
Vibration Safety
This tool vibrates during use.
Repeated or long-term exposure to vibration may
cause temporary or permanent physical injury,
particularly to the hands, arms and shoulders.
To reduce the risk of vibration-related injury:
1. Anyone using vibrating tools regularly or for an
extended period should first be examined by a
doctor and then have regular medical check-ups to
ensure medical problems are not being caused or
worsened from use. Pregnant women or people who
have impaired blood circulation to the hand, past
hand injuries, nervous system disorders, diabetes,
or Raynaud’s Disease should not use this tool.
If you feel any symptoms related to vibration (such
as tingling, numbness, and white or blue fingers),
seek medical advice as soon as possible.
SAVE THESE INSTRUCTIONS.
2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.
3. Wear suitable gloves to reduce the
vibration effects on the user.
4. Use tools with the lowest vibration
when there is a choice.
5. Include vibration-free periods each day of work.
6. Grip tool as lightly as possible (while still keeping
safe control of it). Let the tool do the work.
7. To reduce vibration, maintain the tool as
explained in this manual. If any abnormal
vibration occurs, stop use immediately.
SAFETYOPERATIONMAINTENANCE SETUP
Page 5For technical questions, please call 1-800-444-3353.Item 69820
Grounding
SAFETY OPERATION MAINTENANCESETUP
the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service
facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician.
TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING
WIRE CONNECTION:
Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded.
Do not modify the power cord plug provided with the tool. Never remove the grounding prong from
Grounded Tools: Tools with Three Prong Plugs
2. The grounding prong in the plug is connected through
the green wire inside the cord to the grounding
system in the tool. The green wire in the cord must
be the only wire connected to the tool’s grounding
system and must never be attached to an electrically
“live” terminal. (See 3-Prong Plug and Outlet.)
3. The tool must be plugged into an appropriate outlet,
properly installed and grounded in accordance with
all codes and ordinances. The plug and outlet should
3-Prong Plug and Outlet
1. Tools marked with “Grounding Required” have a three
wire cord and three prong grounding plug. The plug
must be connected to a properly grounded outlet.
If the tool should electrically malfunction or break
down, grounding provides a low resistance path to
carry electricity away from the user, reducing the risk
of electric shock. (See 3-Prong Plug and Outlet.)
look like those in the preceding illustration.
(See 3-Prong Plug and Outlet.)
Double Insulated Tools: Tools with Two Prong Plugs
1. Tools marked “Double Insulated” do not
require grounding. They have a special
double insulation system which satisfies
OSHA requirements and complies with
the applicable standards of Underwriters
Laboratories, Inc., the Canadian Standard
Association, and the National Electrical Code.
2. Double insulated tools may be used in either of the
120 volt outlets shown in the preceding illustration.
Outlets for 2-Prong Plug
(See Outlets for 2-Prong Plug.)
Extension Cords
1. Grounded tools require a three wire extension cord.
Double Insulated tools can use either
a two or three wire extension cord.
2. As the distance from the supply outlet increases,
you must use a heavier gauge extension cord.
Using extension cords with inadequately sized wire
causes a serious drop in voltage, resulting in loss of
power and possible tool damage. (See Table A.)
3. The smaller the gauge number of the wire, the
greater the capacity of the cord. For example,
a 14 gauge cord can carry a higher current
than a 16 gauge cord. (See Table A.)
4. When using more than one extension cord to make
up the total length, make sure each cord contains at
least the minimum wire size required. (See Table A.)
Page 6 For technical questions, please call 1-800-444-3353. Item 69820
5. If you are using one extension cord for more
than one tool, add the nameplate amperes
and use the sum to determine the required
minimum cord size. (See Table A.)
6. If you are using an extension cord outdoors, make
sure it is marked with the suffix “W-A” (“W” in
Canada) to indicate it is acceptable for outdoor use.
7. Make sure the extension cord is properly wired
and in good electrical condition. Always replace
a damaged extension cord or have it repaired
by a qualified electrician before using it.
8. Protect the extension cords from sharp objects,
excessive heat, and damp or wet areas.
Symbology
TABLE A: RECOMMENDED MINIMUM WIRE
GAUGE FOR EXTENSION CORDS* (120/240 VOLT)
NAMEPLATE
AMPERES
(at full load)
0 – 2.0 18 18 18 18 16
2.1 – 3.4 18 18 18 16 14
3.5 – 5.0 18 18 16 14 12
5.1 – 7.0 18 16 14 12 12
7.1 – 12.0 18 14 12 10 -
12.1 – 16.0 14 12 10 - -
16.1 – 20.0 12 10 - - -
* Based on limiting the line voltage drop to five volts at
150% of the rated amperes.
EXTENSION CORD
LENGTH
25´ 50´ 75´ 100´ 150´
SAFETYOPERATIONMAINTENANCE SETUP
V
~
A
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
Volts
Alternating Current
Amperes
n0 xxxx/min.
No Load Revolutions per Minute (RPM)
WARNING marking concerning Risk
of Eye Injury. Wear ANSI-approved
safety goggles with side shields.
Read the manual before
set-up and/or use.
WARNING marking
concerning Risk of Fire.
Do not cover ventilation ducts.
Keep flammable objects away.
WARNING marking concerning
Risk of Electric Shock.
Properly connect power cord
to appropriate outlet.
Page 7For technical questions, please call 1-800-444-3353.Item 69820
SAFETY OPERATION MAINTENANCESETUP
Specifications
Electrical Rating 120V~ / 60 Hz / 10 A
No Load Speed 900 –1600 FPM
Belt Size 4" W x 24" L
254813
Page 8 For technical questions, please call 1-800-444-3353. Item 69820
Setup - Before Use:
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
Note: For additional information regarding the parts listed in the following pages,
refer to Parts List and Diagram on page 14.
Functions
SAFETYOPERATIONMAINTENANCE SETUP
Speed Control Knob
Carbon Brush Cover
Tracking Knob
Trigger Lock
Trigger
Drive Belt Cover
Dust Bag
Front Handle
Rear Handle
Power Cord
Belt Tension
Release Lever
Page 9For technical questions, please call 1-800-444-3353.Item 69820
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
SAFETY OPERATION MAINTENANCESETUP
Tool Set Up
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Make sure that the Trigger is in the off-position and unplug the tool from its
electrical outlet before performing any procedure in this section.
1. Secure the Dust Bag to the tool. 2. Before use, make sure that the Sanding Belt is
on-center. To check this, plug in the sander and hold
the Belt clear while carefully turning on the tool. If
the Belt moves to one side or the other during use,
turn the Tracking Knob until it stays on-center.
Workpiece and Work Area Set Up
1. Designate a work area that is clean and well-lit.
The work area must not allow access by children
or pets to prevent distraction and injury.
2. Route the power cord along a safe route to reach
the work area without creating a tripping hazard or
exposing the power cord to possible damage. The
power cord must reach the work area with enough
extra length to allow free movement while working.
General Operating Instructions
1. Make sure that the Trigger is not
engaged, then plug in the tool.
2. To start the tool, squeeze the Trigger;
release the Trigger to stop. For continuous
operation squeeze the Trigger and push
the Trigger Lock to lock the tool on.
3. To turn the tool off with Trigger Lock engaged,
squeeze the Trigger once and then release.
4. Adjust the sander speed to suit different working
material. Turn the Speed Control Knob to a higher
number for a faster speed or to a lower number
for a slower speed. Determine the optimum
speed by testing on a scrap piece of material.
3. Secure loose workpieces using a vise or clamps
(not included) to prevent movement while working.
4. There must not be objects, such as utility lines,
nearby that will present a hazard while working.
5. When sanding, use both hands to hold the tool
and sand along the grain for best results.
6. Hold the tool lightly on the workpiece and allow
the tool to do the work. Do not push down on the
Belt Sander or move it along the surface too fast.
7. To prevent accidents, turn off the tool and
unplug it after use. Clean, then store the
tool indoors out of children’s reach.
Note: Using the correct speed for the
job increases the life of the tool.
Page 10 For technical questions, please call 1-800-444-3353. Item 69820
Maintenance and Servicing
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Make sure that the Trigger is in the off-position and unplug the tool from its
electrical outlet before performing any procedure in this section.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration
occurs, have the problem corrected before further use.
Cleaning, Maintenance, and Lubrication
SAFETYOPERATIONMAINTENANCE SETUP
1. BEFORE EACH USE, inspect the general
condition of the tool. Check for:
• loose hardware
• misalignment or binding of moving parts
• damaged cord/electrical wiring
• worn or torn sanding belt
• cracked or broken parts
• any other condition that may
affect its safe operation.
2. AFTER USE, wipe external surfaces
of the tool with clean cloth.
3. Regularly check to see if any dust or foreign
matter has entered the tool’s air vents near
the motor and around the trigger. Keep the
vents unclogged and clean at all times.
4. When a sanding belt tears or becomes
worn, it must be replaced:
a. Always turn the tool off and unplug
it before changing the belt.
b. Pull out the Belt Tension Release Lever and
push it forward until it locks into place.
c. Remove the old belt and replace with a
new 4" x 24" belt. Make sure the arrows
on the inside of the new sanding belt are
pointing in the direction of rotation as
indicated on the housing of the tool.
d. Push the Belt Tension Release Lever
back in to secure the belt in place.
e. Make sure the new belt is on-center before use.
5. To replace a worn or broken Drive Belt:
a. Make sure the tool is turned off and
unplugged before changing the belt.
b. Remove the cover mounting screw
holding the Drive Belt Cover in place.
c. Remove the Drive Belt Cover.
d. Take out the worn or broken belt and
install a new belt by sliding it around
the Small and Large Belt Pulleys.
e. Replace the Drive Belt Cover and secure it
in place with the cover mounting screw.
6. CARBON BRUSH MAINTENANCE.
The Carbon Brushes may require maintenance
when the motor performance of the tool decreases
or stops working completely. Carbon brushes are
internal to the Motor Housing, and should only
be replaced by a qualified service technician.
a. To replace brushes, remove the Carbon
Brush Cover with a screwdriver. Then
remove Carbon Brush from Brush Holder.
b. Insert new Carbon Brush into Holder, replace
the Carbon Brush Cover and tighten with a
screwdriver. Make sure the carbon portions of
the Carbon Brushes contact the motor armature,
and that the springs face away from the motor.
c. When replacing Carbon Brushes both
brushes must be replaced. Repeat steps
"a" and "b" for the second brush.
Note: New carbon brushes tend to spark when first used
until they wear and conform to the motor’s armature.
7. WARNING! If the supply cord of this
power tool is damaged, it must be replaced
only by a qualified service technician.
Page 11For technical questions, please call 1-800-444-3353.Item 69820
Troubleshooting
Problem Possible Causes Likely Solutions
Tool will not start. 1. Cord not connected.
SAFETY OPERATION MAINTENANCESETUP
Tool operates slowly. 1. Forcing tool to work too fast.
Performance
decreases over time.
Excessive noise
or rattling.
Overheating. 1. Forcing tool to work too fast.
2. No power at outlet.
3. Tool’s thermal reset breaker
tripped (if equipped).
4. Internal damage or wear.
(Carbon brushes or
Trigger, for example.)
2. Extension cord too long or cord
diameter too small.
Carbon brushes worn or damaged. Have qualified technician replace brushes.
Internal damage or wear. (Carbon
brushes or bearings, for example.)
2. Blocked motor housing vents.
3. Motor being strained by long or
small diameter extension cord.
1. Check that cord is plugged in.
2. Check power at outlet. If outlet is unpowered,
turn off tool and check circuit breaker.
If breaker is tripped, make sure circuit is right
capacity for tool and circuit has no other loads.
3. Turn off tool and allow to cool.
Press reset button on tool.
4. Have technician service tool.
1. Allow tool to work at its own rate.
2. Eliminate use of extension cord. If an extension
cord is needed, use one with the proper diameter
for its length and load. See Extension Cords
in Grounding section on page 6.
Have technician service tool.
1. Allow tool to work at its own rate.
2. Wear ANSI-approved safety goggles and
NIOSH-approved dust mask/respirator while
blowing dust out of motor using compressed air.
3. Eliminate use of extension cord. If an extension
cord is needed, use one with the proper diameter
for its length and load. See Extension Cords
in Grounding section on page 6.
Follow all safety precautions whenever diagnosing or servicing the tool.
Disconnect power supply before service.
Page 12 For technical questions, please call 1-800-444-3353. Item 69820
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
SAFETYOPERATIONMAINTENANCE SETUP
Page 13For technical questions, please call 1-800-444-3353.Item 69820
Parts List and Diagram
Parts List
SAFETY OPERATION MAINTENANCESETUP
Part Description Qty
1 Screw St4.2 x 16 11
2 Screw St4.2 x 40 2
3 Side Cover 1
4 Dust Fan Housing 1
5 Screw St4.2 x 40 1
6 Spring Washer Ø5 2
7 Washer Ø5 2
8 Dust Exhaust Fan 1
9 Middle Cover 1
10 Bearing 6000 2
11 Armature 1
12 Right Housing 1
13 Trigger 1
14 Power-On Indicator Lamp 1
15 Lens 1
16 Speed Control Knob 1
17 Power Cord 1
18 Power Cord Clamp 1
19 Power Cord Sleeve 1
20 Left Housing 1
21 Front Bushing Frame 1
22 Dust Bag 1
23 Small Belt Pulley 1
24 Drive Belt Cover 1
25 Nameplate 1
26 Screw M4 x 14 4
27 Spring Washer Ø4 2
28 Washer Ø4 2
29 Brush Holder 2
30 Carbon Brush 2
31 Carbon Brush Cover 2
32 Stator 1
33 Screw St4.8 x 45 2
34 Sanding Belt 1
35 Frame Cover 1
Part Description Qty
36 Spring 1
37 Nut M12 1
38 Bolt M6 1
39 Baffle Plate 1
40 Rear Bushing 1
41 Needle Bearing Hk1514 1
42 Bearing 6001 1
43 Gearbox 1
44 Screw St4.2 x 55 1
45 Rear Bushing Axle 1
46 Large Gear 1
47 Clip Spring Ø12 1
48 Woodruff Key 1
49 Needle Bearing Bk0810 1
50 Shaft Gear 1
51 Bearing 6200 1
52 Gear Box Cover 1
53 Large Belt Pulley 1
54 Nut M10 1
55 Drive Belt 1
56 Tracking Knob 1
57 Washer Ø22 1
58 Spring 1
59 Nut M6 1
60 Nameplate 1
61 Screw M5 x 12 1
62 Rubber Cushion 1
63 Mounting Plate 1
64 Screw M4 x 12 3
65 Spring 1
66 Bowl-Type Washer Ø12 2
67 Needle Bearing Hk121816 2
68 Front Bushing Axle 1
69 Front Bushing 1
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
Page 14 For technical questions, please call 1-800-444-3353. Item 69820
Assembly Diagram
SAFETYOPERATIONMAINTENANCE SETUP
Page 15For technical questions, please call 1-800-444-3353.Item 69820
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Loading...