Specifications
Rated Capacity 4,000 lb.
Compatibility
Pittsburgh® item 68048, 68049, 68050,
68056, 60678, 60688, 60706, or 69227
Important Safety Information
Failure to heed these markings may result in personal injury and/or property damage:
1. Study, understand, and follow all
instructions before operating this device.
2. Do not exceed 4,000 lb. rated capacity.
3. Assure load is secured to the device.
4. To be used only with the following:
Pittsburgh® item 68048, 68049, 68050,
68056, 60678, 60688, 60706, or 69227.
5. Release load locking devices
(if employed) slowly and carefully.
6. No alterations shall be
made to this product.
7. Adjust pads to keep bar
level during lifting.
8. Only use with included safety
chains properly connected to
prevent overextension.
9. Install and use aligned perpendicular
to floor jack body only.
10. Also, study, understand, and
follow all floor jack instructions
before operating this device.
11. Wear ANSI-approved safety goggles
and heavy-duty work gloves during use.
12. Do not move or dolly the vehicle
while on the cross beam.
13. Use as intended only.
Do not use for lifting human weight.
Keep clear of raised load.
Do not use for aircraft purposes.
14. Lift vehicle only at
manufacturer-recommended locations.
15. Inspect before every use;
do not use if parts loose or damaged.
16. Lifting device only.
Immediately after lifting, support the
vehicle with appropriate means.
Assembly Instructions
1. Remove saddle mounting bolt
and saddle from Floor Jack.
2. Place Cross Beam on Floor Jack.
3. For 2 or 2.5 ton floor jacks,
slide Spacer onto Mounting Bolt
before installing it.
4. Install Cross Beam’s Mounting Bolt
and tighten it securely in place
while keeping Cross Beam aligned
perpendicular to Floor Jack body.
Page 2 For technical questions, please call 1-800-444-3353. Item 60762
Operation Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the
beginning of this document including all text under subheadings therein
before set up or use of this product.
1. Lower both Saddle Pads completely.
2. Align each Saddle Pad
under a vehicle lifting point.
Center the vehicle’s weight
over the Floor Jack.
WARNING! Lift vehicle only at
manufacturer-recommended locations.
3. Use Floor Jack to raise Cross Beam
until one of the Saddle Pads is about to
contact one of the vehicle lifting points.
4. Turn the Saddle Pads to
adjust each one until they both
contact the lifting points.
Parts List and Diagram
5. Stay clear of vehicle, Jack and
Cross Beam while slowly raising the
vehicle until it is at the desired height.
WARNING! While lifting, make sure
that the Cross Beam remains level and
the load is centered over the Floor Jack.
6. Place two Jack Stands at
manufacturer-recommended support
points and adjust until they almost
contact each support point.
7. Stay clear while lowering the vehicle
onto the Jack Stands. Lower the
vehicle’s weight completely onto
Jack Stands before working under it.
Part Description Qty
1 Housing 1
2 Extension 2
3 Saddle 2
4 Saddle Pad 2
Part Description Qty
5 Bolt 8
6 Chain 2
7 Washer 2
8 Spring Washer 2
10
1
11
Record Serial Number Here:
Note: If product has no serial number,
record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes
only, and are not available individually as replacement parts.
Part Description Qty
9 Chain Bolt 2
10 Mounting Bolt 1
11 Spacer* 1
*For 2 and 2.5 ton jack mounting.
5
4
2 3
6
7
8
9
Page 3For technical questions, please call 1-800-444-3353.Item 60762
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER
OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE
BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR
THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE
MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS
REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS,
AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF
HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO,
OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free from
defects in materials and workmanship for the period of 90 days from the date of purchase.
This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence
or accidents, repairs or alterations outside our facilities, criminal activity, improper installation,
normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages
arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to you.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation
charges prepaid. Proof of purchase date and an explanation of the complaint must accompany
the merchandise. If our inspection verifies the defect, we will either repair or replace
the product at our election or we may elect to refund the purchase price if we cannot readily
and quickly provide you with a replacement. We will return repaired products at our expense,
but if we determine there is no defect, or that the defect resulted from causes not within
the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Loading...