Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
REV 15c
Email our technical support at: productsupport@harborfreight.com
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 1997 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Specifications
Operating Instructions
Slide Hammer Weight 2 LB.
Rod Threads 7/16"-14
Important Safety Information
1. Assemble only according to these
instructions. Improper assembly
can create hazards.
2. Wear ANSI-approved safety
goggles and heavy-duty work
gloves during assembly.
3. Keep work area clean and well lit.
4. Keep bystanders out of
work area during use.
5. Do not use when tired or when under
the influence of drugs or medication.
6. This product is not a toy. Do not allow
children to play with or near this item.
7. Use as intended only.
8. Inspect before every use; do not
use if parts are loose or damaged.
Assembly
1. Slide Handle Crossbar (2) through hole
in the handle-end of Slide Screw (3).
2. Place Slide Hammer (12)
onto the Slide Screw.
3. Assemble attachments based on the
intended use of the Slide Hammer
(see Operation Instructions below)..
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of
this document including
all text under subheadings
therein before set up or
use of this product.
NOTE: This tool will exert strong forces
on the object being pulled and may
damage some objects during removal,
depending on the force required.
Two-Jaw Pulling
1. Decide if you need the Small Jaws
(9), Large Jaws (10) or the TwoJaw Puller Adapter (8). The Adapter
is smaller and should be used for
narrower, hard-to-reach objects.
2. Determine if you need to attach the
Jaws for an internal or external pull.
• An external pull allows the
jaws to grip the outside
surface of the object.
• An internal pull allows the jaws to
grip the inside surface of the object.
3. Assemble the Small Jaws or Large
Jaws to the Jaw Adapter using the
two Locking Pins (1). If you are
using the Two-jaw Puller Adapter,
attach it directly to the threaded
end of the Slide Screw (3).
4. Thread the assembled Jaws/Jaw
Adapter onto end of Slide Screw.
5. Attach the Jaws to the
object to be pulled.
6. Push the Slide Hammer toward the
object to be pulled. Forcefully pull the
Slide Hammer toward the handle end.
7. Repeat Step Six until the object
is successfully pulled.
Page 2 For technical questions, please call 1-888-866-5797. Item 05469
Bolt Removal
1. Attach the Cone Rod (6) to the end
of the Screw Adapter (7), then attach
this piece directly to the Slide Screw.
2. The Cone Rod works like an easyout bolt remover. Center the point
of the Cone Rod in the middle
of the bolt to be removed.
3. FORCEFULLY push the Slide
Hammer into the bolt to be removed.
4. Turn the Slide Screw
COUNTERCLOCKWISE as you
pull out the bolt. Continue to twist
and pull COUNTERCLOCKWISE
until bolt is removed.
Hook Pulling
1. Attach the Puller Hook (11)
or the Square Hook (5) to the
end of the Slide Screw.
2. Identify the lip area or edge of
the object you will be inserting
the chosen Hook into or onto.
3. Place the Hook into/onto the edge
or lip of the object to be pulled.
4. Push the Slide Hammer toward the
object to be pulled. Pull the Slide
Hammer toward the handle end.
5. Repeat Step Four until the
object has been pulled out.
Maintenance and Servicing
1. BEFORE EACH USE, inspect the
general condition of the tool. Check
for loose attachments, binding of
moving parts, cracked or broken
Attachments, and any other condition
that may affect its safe operation. If
any abnormality is found, have the
problem corrected before further use.
2. AFTER EACH USE, wipe off all
parts with clean, moist cloth.
3. Lubricate attachments regularly
to ensure smooth operation.
4. Replace attachment if threads
wear and will not attach
securely to Slide Hammer.
Record Serial Number Here:
Note: If product has no serial number,
record month and year of purchase instead.
Note: Some parts are listed and shown
for illustration purposes only, and are not
available individually as replacement parts.
PLEASE READ THE
FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR
HAS PROVIDED THE PARTS LIST AND
ASSEMBLY DIAGRAM IN THIS DOCUMENT
AS A REFERENCE TOOL ONLY. NEITHER
THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR
WARRANTY OF ANY KIND TO THE BUYER
THAT HE OR SHE IS QUALIFIED TO MAKE
ANY REPAIRS TO THE PRODUCT, OR THAT
HE OR SHE IS QUALIFIED TO REPLACE ANY
PARTS OF THE PRODUCT. IN FACT, THE
MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS
AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK
AND LIABILITY ARISING OUT OF HIS OR
HER REPAIRS TO THE ORIGINAL PRODUCT
OR REPLACEMENT PARTS THERETO, OR
ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
Page 3For technical questions, please call 1-888-866-5797.Item 05469
Parts List and Diagram
Part Description Qty
1 Locking Pin 2
2 Handle Crossbar 1
3 Slide Screw 1
4 Two-Jaw Puller 1
5 Square Hook 1
6 Cone Rod 1
*NOTE: The thread-on Screw Adapter allows for the use of additional pulling attachments that use a smaller diameter thread.
Part Description Qty
7 Screw Adapter* 1
8 Jaw Adapter 1
9 Small Jaw 2
10 Large Jaw 2
11 Puller Hook 1
12 Slide Hammer 1
5 4 3 2 16
9
10
11
12
8
7
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797
Loading...