Harbor Freight Tools English Wheel Kit with Stand Product manual

English Wheel

Item 68385

INSTRUCTIONS AND PRECAUTIONS

Visit our website at:

http://www.harborfreight.com

Read this material before
using this product.
Failure to do so can result
in serious injury.
SAVE THIS MANUAL.

Specications

Upper Wheel Size 8" radius x 2" W

Lower Wheel Included 3” curved radius x 2" W

Throat Size 27-3/4"

Stock Applications

Features

16 gauge sheet metal,
14 (1/8") soft aluminum
and copper

Lower Wheel Rack
Quick-Adjust Lower Bracket

Important Safety Information

1. Wear ANSI-approved safety goggles and
heavy-duty work gloves during setup and use.
Wear a durable long-sleeved shirt or coat
when working with large workpieces.

2. Wheel may crush and injure hands! Keep hands out of
line of wheel during use. Do not use too tight a pinch,
it will increase the amount of force used and increase

the chance of accidentally crushing your nger.

3. Assemble only according to these instructions.
Improper assembly can create hazards.

4. Keep assembly area clean and well lit.

5. Keep bystanders out of the area during assembly.

6. Do not assemble when tired or when under the

inuence of alcohol, drugs or medication.

7. This product is not a toy. Do not allow
children to play with or near this item.

8. Use as intended only.

9. Inspect before every use; do not use
if parts are loose or damaged.

10. To improve stability, bolt to oor before use.
Verify that installation surface has no hidden
utility lines before drilling or driving screws.

11. Maintain product labels and nameplates. These carry
important safety information. If unreadable or missing,
contact Harbor Freight Tools for a replacement.

When unpacking, make sure
that the product is intact and
undamaged.
If any parts are missing or broken,
please call 1-800-444-3353
as soon as possible.

Copyright© 2011 by Harbor Freight Tools®. All rights reserved. No
portion of this document or any artwork contained herein may
be reproduced in any shape or form without the express written
consent of Harbor Freight Tools. Diagrams within this document
may not be drawn proportionally. Due to continuing improvements,
actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.

For technical questions or replacement

REV 12a

parts, please call 1-800-444-3353.

Assembly Instructions

Read the ENTIRE IMPORTANT SAFETY

INFORMATION section at the beginning
of this document including all text
under subheadings therein before
set up or use of this product.

Note: For additional information regarding the

parts listed in the following pages, refer to the
Assembly Diagram near the end of this manual.

Unpack the English Wheel components and lay

out on the oor where the unit will be located and
mounted. The oor must be able to support the

weight of the English Wheel and the work pieces.

a

bc

Figure 1

To attach the legs and footing:

1.

a. Using two Bolts (25), and Washers (26) attach

the Back Leg (27) to the Connecting Brace (24).

b. Attach the other end of the Connecting Brace

(24) to the Front Footing (22) with the remaining
two Bolts (25) and two of the Washers.

c. Attach the Front Leg (28) to the top of the Front

Footing (22) with four Bolts (23) and Washers (26).

Figure 2

2.

With the help of at least two other people, lift the
Frame (1) and place it on the assembled legs and feet,
aligning the bracket holes. Bolt in place with the four
Bolts (29), eight Washers, and four Nuts (30).Check
that the Frame is square, then securely tighten all bolts.

Page 2 For technical questions, please call 1-800-444-3353. SKU 68385

Figure 3Figure 3

3.

Bolt the Upper Wheel Bracket (3) to the Main Frame (1)
using two Bolts (9) and Washers (8).

Figure 4

Slide the Upper Wheel Shaft (2) through one side of the

4.
Bracket (3), a Washer (7), Bearing (6), Upper Wheel
(5), Bearing (6), Washer (7) and through the other side
of the Bracket. Secure in place with the Circlips (4) at
each end.

5.

Slide the Adjustable Shaft (16) into the top of
the channel of the Main Frame. Thread the
Locking Nut (32) onto the Guide Bolt (31). Align

the slot in the Shaft with the Bolt hole, and nger

tighten the Bolt. Make sure the Shaft will not
turn but can still slide up and down freely, then
secure bolt in place with the Locking Nut.

6. Thread the Ball Handle (15) onto the Release Handle
(14) and the Handle into the bar on the Lower Wheel
Bracket (13). Place the Bracket on top of the Shaft (16).

Page 3For technical questions, please call 1-800-444-3353.SKU 68385