Harbor Freight Tools Electric Multipurpose Sharpener Product manual
MULTI-PURPOSE ELECTRIC
SHARPENER
Model
99823
SET UP AND OPERATING INSTRUCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of Harbor
Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly
and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Manual Revised 10e
SAVE THIS MANUAL
Keep this manual for the safety
warnings and precautions, assembly,
operating, inspection, maintenance and
cleaning procedures. Write the product’s
serial number in the back of the manual
near the assembly diagram (or month
and year of purchase if product has no
number). Keep this manual and the
receipt in a safe and dry place for future
reference.
IMPORTANT SAFETY
INSTRUCTIONS
In this manual, on the labeling,
and all other information
provided with this product:
This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that
follow this symbol to avoid
possible injury or death.
DANGER indicates
a hazardous
situation which, if not
avoided, will result in death or
serious injury.
WARNING
indicates a
hazardous situation which, if
not avoided, could result in
death or serious injury.
CAUTION, used
with the safety
alert symbol, indicates a
hazardous situation which, if
not avoided, could result in
minor or moderate injury.
NOTICE is used to
address practices
not related to personal injury.
CAUTION, without
the safety alert
symbol, is used to address
practices not related to
personal injury.
READ AND UNDERSTAND ALL
INSTRUCTIONS
When using electrical tools,
safety precautions should
always be followed including the
following:
Work Area Safety
Do not use outdoors.1.
Close supervision is necessary when 2.
any tool is used by or near children.
Do not let cord hang over edge 3.
of table or counter, or touch hot
surfaces.
Do not place on or near a hot gas or 4.
electric burner, or in a heated oven.
Extreme caution must be used when 5.
moving an tool.
Keep the work area well lit. Make 6.
sure there is adequate surrounding
workspace. Keep the work area free
of obstructions and other debris.
SKU 99823 For technical questions, please call 1-800-444-3353. Page 2
Electrical Safety
tripping over a longer cord.
1. To protect against
electrical shock do not
immerse cord, plugs, or
the main unit in water or
other liquid. Only the
non-electrical parts of the unit may be
immersed for cleaning. Thoroughly
clean and dry these parts prior to rst
use and before every subsequent
use.
Unplug from outlet when not in use 2.
and before maintenance or cleaning.
Do not operate any tool with a 3.
damaged cord or plug or after the tool
malfunctions or has been damaged
in any manner. Return tool to the
nearest authorized service facility for
examination, repair, or adjustment.
This Electric Sharpener has a 4.
polarized plug (one blade is wider
than the other). To reduce the risk of
electric shock, this plug is intended
to t into a polarized outlet only one
way. If the plug does not t fully
in the outlet, reverse the plug. If it
still does not t, contact a qualied
electrician. Do not change the plug in
any way.
2. Longer extension cords are available
and may be used if care is exercised
in their use.
3. If a long extension cord is used,
the marked electrical rating of the a.
(detachable power supply cord or)
extension cord should be at least as
great as the electrical rating of the
tool,
if the tool is of the grounded type, b.
the extension cord should be a
grounding type 3-wire cord, and
the longer cord should be arranged c.
so that it will not drape over the
counter top or tabletop where it can
be pulled on by children or tripped
over.
General Safety
The use of accessory attachments 1.
not recommended by the tool
manufacturer may cause injuries.
To disconnect, turn any control to 2.
“off”, then remove plug from wall
outlet.
Do not use tool for other than 3.
intended use.
Do not use this product in a damp or 5.
wet location.
Do not clean with metal scouring 6.
pads. Metal pieces can break off
the pads and touch electrical parts
involving risk of shock.
Power Cord Safety
1. A short power supply cord is to be
provided to reduce risks resulting
from becoming entangled in or
SKU 99823 For technical questions, please call 1-800-444-3353. Page 3
Maintain labels and nameplates on 4.
the tool. These carry important safety
information. If unreadable or missing,
contact Harbor Freight Tools for a
replacement.
Do not store anything other than 5.
the manufacturer’s recommended
accessories in this unit when not in
use.
This product is not a toy. Keep it out 6.
of reach of children when children are
not being closely supervised.
Knives with serrated edges are a 3.
good example of blades that may not
be suited for this Electric Sharpener.
People with pacemakers should 7.
consult their physician(s) before
use. Electromagnetic elds in close
proximity to heart pacemaker could
cause pacemaker interference or
pacemaker failure.
WARNING: The brass components 8.
of this product contain lead, a
chemical known to the State of
California to cause birth defects (or
other reproductive harm). (California
Health & Safety code § 25249.5, et
seq.)
WARNING: Handling the cord on 9.
this product will expose you to lead,
a chemical known to the State of
California to cause cancer, and
birth defects or other reproductive
harm. Wash hands after handling.
(California Health & Safety Code §
25249.5, et seq.)
This Multi-purpose Electric Sharpener 4.
is not recommended for professional
applications.
SAVE THESE
INSTRUCTIONS.
SPECIFICATIONS
Electrical
Requirements
Cord Length 6’ L
Speed 4800 RPM
Switch Rocker Type ON/OFF
Applications
Minimum size drill bit 1/8”
120 V~ / 60 Hz / 70 W
Drill Bits: 1/8” ~ 3/8”
(3~10mm)
Chisels/Planer Blades:
1/4” ~ 2” W
Most Knives and Scissors.
The warnings, precautions, and 10.
instructions discussed in this
instruction manual cannot cover all
possible conditions and situations
that may occur. It must be understood
by the operator that common sense
and caution are factors which cannot
When unpacking, check to make sure
that the item is intact and undamaged. If
any parts are missing or broken, please
call Harbor Freight Tools at the number
shown on the cover of this manual as soon
as possible.
UNPACKING
be built into this product, but must be
supplied by the operator.
Specic Safety Rules
Grinding wheel MUST BE rated to 1.
at least 4800 RPM.
Wear ANSI-approved safety 2.
goggles and heavy-duty work
gloves during set up and use.
REV 08k
SKU 99823 For technical questions, please call 1-800-444-3353. Page 4
Loading...