Page 1
STAPLE GUN
Model
96755
3-WAY TACKER KIT
SET UP AND OPERATING INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright© 2007 by Harbor Freight Tools®. All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Page 2
SAVE THIS MANUAL
Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number
in the back of the manual near the assembly diagram (or month and year of purchase if
product has no number). Keep this manual and the receipt in a safe and dry place for
future reference.
IMPORTANT SAFETY INFORMATION
In this manual, on the labeling, and all other
information provided with this product:
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.
DANGERDANGER
WARNINGWARNING
CAUTIONCAUTION
NOTICENOTICE
CAUTIONCAUTION
DANGER indicates a hazardous situation
which, if not avoided, will result in death or
serious injury.
WARNING indicates a hazardous situation
which, if not avoided, could result in death
or serious injury.
CAUTION, used with the safety alert
symbol, indicates a hazardous situation
which, if not avoided, could result in minor
or moderate injury.
NOTICE is used to address practices not
related to personal injury.
CAUTION, without the safety alert symbol,
is used to address practices not related to
personal injury.
Page 2SKU 96755 For technical questions, please call 1-800-444-3353.
Page 3
GENERAL SAFETY RULES
WARNING! Read all instructions
Failure to follow all instructions listed below may result in electric shock,
re, and/or serious injury.
SAVE THESE INSTRUCTIONS
Keep your work area clean and well lit. Cluttered benches and dark areas
1.
invite accidents.
Keep bystanders, children, and visitors away while using this product.
2.
Distractions can cause you to lose control. Protect others in the work area from
debris such as staples. Provide barriers or shields as needed. Keep children
out of the work area.
Stay alert. Watch what you are doing, and use common sense when
3.
operating the Staple Gun. Do not use this product while tired or under the
inuence of drugs, alcohol, or medication. A moment of inattention while
operating this product may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
4.
Keep your hair, clothing, and gloves out of the way of the jaws. Loose
clothes, jewelry, or long hair can be caught in moving parts.
Do not overreach. Keep proper footing and balance at all times. Proper
5.
footing and balance enables better control of this product in unexpected situa-
tions.
Use safety equipment. Always wear eye protection. Always wear ANSI-ap-
6.
proved safety goggles when working with this tool.
Use clamps (not included) or other practical ways to secure and support
7.
the workpiece to a stable platform. Holding the work by hand or against your
body is unstable and may lead to loss of control.
Do not force the product. Use the correct product for your application.
8.
The correct product will do the job better and safer at the rate for which it is
designed. Do not force the product and do not use the product for a purpose for
which it is not intended.
Store idle products out of reach of children and other untrained persons.
9.
This product is dangerous in the hands of untrained users.
Never aim the Staple Gun at any person, child or animal.
10.
Maintain this product with care. Do not use a damaged product. Tag dam-
11.
aged products “Do not use” until repaired.
Check for misalignment or binding of moving parts, breakage of parts, and
12.
any other condition that may affect the product’s operation. If damaged,
have the product serviced before using. Many accidents are caused by
poorly maintained products.
Page 3SKU 96755 For technical questions, please call 1-800-444-3353.
Page 4
Use only accessories that are recommended by the manufacturer for your
13.
model. Accessories that may be suitable for one product may become hazard-
ous when used on another product.
14.
When servicing a product, use only identical replacement parts. Follow
instructions in the “Inspection, Maintenance, And Cleaning” section of this
manual. Use of unauthorized parts or failure to follow maintenance instructions
may create a risk of electric shock or injury.
15.
Maintain labels and nameplates on the product. These carry important in-
formation. If unreadable or missing, contact Harbor Freight Tools for a replace-
ment.
16.
Maintain a safe working environment. Make sure there is adequate surround-
ing workspace. Do not use this product in a damp or wet location.
17.
Always keep hands away from work piece. This Staple Gun has enough
power to force a staple through skin causing serious injury.
SPECIFICATIONS
Stapler Dimensions 6-5/16” x 5-1/2” W x 1-3/16” diameter
Trigger Palm Squeeze type
Fastener Types Included Standard staples, brad nails and U-shaped staples
Magazine Spring loaded slide strip
UNPACKING
When unpacking, check to make sure that the item is intact and undamaged. If
any parts are missing or broken, please call Harbor Freight Tools at the number shown
on the cover of this manual as soon as possible.
List of contents
Part(s) Description Q’ty
Staple Gun 1
Standard
Staples
Brad Nails (500) 3/8” 500
U-Shaped
Staples
(500) T50, 3/8” crown x 5/16” L 500
(500) 1/4” crown x 1/2” L 500
Page 4SKU 96755 For technical questions, please call 1-800-444-3353.
Page 5
SET UP INSTRUCTIONS
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the
beginning of this manual including all text under subheadings therein
before set up or use of this product.
Note: For additional information regarding the parts listed in the following pages, refer
to the Assembly Diagram near the end of this manual.
Loading the Staples
Figure 1
Push in and down to release the
Staple Channel Latch.
Push the End Clip forward and down to release the Staple Channel Latch. Pull
1.
out the Staple Channel-see Figure 1.
Figure 2
Standard
staple
Load the staples or brad nails into the Staple Channel. Each of the fasteners is
2.
to be loaded into the Staple Channel with its sharp end facing the base of the
Staple Channel-see Figure 2.
Staples are to be inserted into the center of the Staple Channel as shown in
Figure 2. Brad nails are to be inserted on either side of the Staple Channel, as
in Figure 2, but not placed in the center of the Staple Channel.
U-Shaped
staple
Brad
Page 5SKU 96755 For technical questions, please call 1-800-444-3353.
Page 6
Figure 3
Depth Adjustment
Knob (1)
To adjust force that will be exerted on the fastener to drive it deeper into the
3.
work piece, use the Depth Adjustment Knob located at the top of the Staple
Gun-see Figure 3. Turn the Depth Adjustment Knob clockwise to increase
the force to drive the fastener, and counterclockwise for less force driving the
fastener.
OPERATING INSTRUCTIONS
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the
beginning of this manual including all text under subheadings therein
before set up or use of this product.
General operating instructions
Push the End Clip forward and down to release the Staple Channel latch. Pull
1.
out the Staple Channel-see Figure 1.
Insert a full strip of fasteners into the Staple Channel. Push the Staple Channel
2.
back into the Staple Gun Body (1). Make certain that it is pushed all the way
back into place before operating the Staple Gun.
Determine whether or not the object being stapled will necessitate extra force
3.
from the Staple Gun. This will depend primarily on the thickness of the item be-
ing stapled. For instance, a large pad of papers will need more force than one
or two sheets being stapled together.
Set the Depth Adjustment Knob (1) accordingly.
4.
Place the item to be stapled below the Driver located on the front of the Staple
5.
Gun.
Grasp the Staple Gun with your ngers inserted into the opening in the Hous-
6.
ing (8) and your palm resting on the Handle (2). Squeeze and pull down on the
Handle (2) to re a fastener.
Test the Staple Gun using a scrap work piece. Make certain that you have the
7.
Depth Adjustment Knob (1) set correctly, and that the fasteners are placed as
you desire.
Page 6SKU 96755 For technical questions, please call 1-800-444-3353.
Page 7
MAINTENANCE AND SERVICING
Cleaning and Removing the Staple Channel
Push the Retaining Clip at the front of the Staple Gun forward to release the
1.
Staple Channel. Pull the two tabs (located midpoint on the bottom of the Staple
Gun) toward the back of the Staple Gun.
The Staple Channel is now free of the Staple Gun and can be cleared of any
2.
jammed fasteners and debris.
Cleaning, maintenance, and lubrication
BEFORE EACH USE, inspect the general condition of this product. Check for
1.
loose screws, cracked or broken parts and any other condition that may affect its
safe operation.
Remove dirt and debris from the Staple Gun using a clean, soft cloth. Do not
2.
use ammable corrosive or abrasive solvents to clean the Staple Gun.
TROUBLESHOOTING
Problem Possible Causes Probable Solutions
Staple Gun does not staple Staples not loaded
Stapler jams during operation Staples jammed in
1.
correctly.
Magazine Unit not fully
2.
and properly inserted into
Staple Gun.
Lever not pulled
3.
completely up and then
fully pressed down.
1. Pull out the Staple Channel.
channel.
Verify that staples are loaded into
1.
the Magazine Unit at and with
prongs facing upward.
Check that Magazine Unit is fully
2.
inserted.
1.
Remove jammed fasteners
2.
from the channel. You may
need to use long-nosed pliers (not included).
Make certain that you are
3.
using correct size fasteners.
Replace Staple Channel.
4.
Page 7SKU 96755 For technical questions, please call 1-800-444-3353.
Page 8
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS
LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL
ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE
OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT
HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN
FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES
THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO,
OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS
THERETO.
PARTS LIST
Part Description Q’ty
1 Depth Adjustment Knob 1
2 Handle 1
3 Handle Ring 1
4 Staple Channel 1
PARTS DIAGRAM
1
7
5
Part Description Q’ty
5 Staple Tab 1
6 Staple Channel Latch 1
7 Retaining Clip 1
8 Housing
2
8
3
6
4
Page 8SKU 96755 For technical questions, please call 1-800-444-3353.
Loading...