For technical questions or replacement parts, please call 1-800-444-3353.
Page 2
SAVE THIS MANUAL
Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number
in the back of the manual near the assembly diagram (or month and year of purchase if
product has no number). Keep this manual and the receipt in a safe and dry place for
future reference.
IMPORTANT SAFETY INSTRUCTIONS
In this manual, on the labeling, and all other information
provided with this product:
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.
DANGER
WARNING
CAUTION
NOTICE
CAUTION
DANGER indicates a hazardous situation
which, if not avoided, will result in death or
serious injury.
WARNING indicates a hazardous situation
which, if not avoided, could result in death
or serious injury.
CAUTION, used with the safety alert
symbol, indicates a hazardous situation
which, if not avoided, could result in minor
or moderate injury.
NOTICE is used to address practices not
related to personal injury.
CAUTION, without the safety alert symbol,
is used to address practices not related to
personal injury.
Side Tube Dimensions5/8” O.D. x 14-1/8” Wide x 48-1/2” Long
Overall Dimensions
Net Weight16 lb.
Formed steel tubing / Camouage polyester with dark olive
green draw strings and hook and loop closures.
9-4/5” to 15-11/16”
18-1/2” Wide x 6” L x 3/16” Thick
5/8” O.D. x 24” Long
60” Long x 48” Wide x 81-1/2” High
(Includes roof and side walls fully assembled)
UNPACKING
When unpacking, check to make sure that the item is intact and undamaged. If
any parts are missing or broken, please call Harbor Freight Tools at the number shown
on the cover of this manual as soon as possible.
SET UP INSTRUCTIONS
Read the ENTIRE IMPORTANT SAFETY INSTRUCTIONS section at the
beginning of this manual including all text under subheadings therein
before set up or use of this product.
Note:
For additional information regarding the parts listed in the following pages, refer
to the Assembly Diagram on page 7 of this manual.
Set the Main Support Frame (3) and the two pieces of Side Frame (2) on a dry, 1.
at, level surface. (See Assy. Diagram.)
Unfold the two Hinging Braces (4) on the Main Support Frame. Then attach the 2.
Support Brace (5) to the Main Support Frame using two Bolts (9), two Flat Wash-
ers (15), and two Lock Nuts (16). (See Assy. Diagram.)
Insert the two Side Frames (2) into the Main Support Frame (3), and fasten the 3.
two Side Frames to the Main Support Frame using two Bolts (14), two Flat Wash-
ers (15), and two Lock Nuts (16). (See Assy. Diagram.)
Afx the Strips of the Fabric Cover (1) around the edges of the Main Support 4.
Frame (3) and Side Frames (2) with the Draw Strings and Hook and Loop Clo-
injury. Do not use damaged equipment. If a problem occurs,
have the problem corrected before further use.
Inspection, maintenance, and cleaning
Damaged equipment can fail, causing serious personal
BEFORE EACH USE,1. inspect the general condition of the Hunting Shelter.
Check for loose screws, misalignment or binding of parts, cracked or broken
parts, damaged fabric, and any other condition that may affect its safe operation.
REGULARLY,2. clear off any debris or water that may accumulate on the Shelter
during use.
AFTER USE,3. clean the Hunting Shelter with a clean, moist cloth and mild deter-
gent. Then dry. Do not use solvents.
Troubleshooting
ProblemPossible CausesProbable Solutions
Hunting Shelter not
properly positioned
against tree.
Too much slack in Rear Cross Bar.1. Adjust Rear Cross Bar for tighter t 1.
against tree.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.