Page 1
TRAILER SWAY
Model
96462
CONTROL KIT
SET-UP AND OPERATING INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
®
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright© 2007 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Page 2
SAVE THIS MANUAL
Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s
serial number in the back of the manual near the assembly diagram (or month and
year of purchase if product has no number). Keep this manual and the receipt in a
safe and dry place for future reference.
IMPORTANT SAFETY INFORMATION
In this manual, on the labeling, and all other information
provided with this product:
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.
DANGERDANGER
WARNINGWARNING
CAUTIONCAUTION
NOTICENOTICE
CAUTIONCAUTION
DANGER indicates a hazardous situation
which, if not avoided, will result in death or
serious injury.
WARNING indicates a hazardous situation
which, if not avoided, could result in death
or serious injury.
CAUTION, used with the safety alert
symbol, indicates a hazardous situation
which, if not avoided, could result in minor
or moderate injury.
NOTICE is used to address practices not
related to personal injury.
CAUTION, without the safety alert symbol,
is used to address practices not related to
personal injury.
Page 2SKU 96462 For technical questions, please call 1-800-444-3353.
Page 3
GENERAL SAFETY RULES
WARNING! Read all instructions.
Failure to follow all instructions listed below may result in serious injury.
SAVE THESE INSTRUCTIONS
1.
2.
Work area safety
Keep assembly area clean and well lit. Cluttered or dark areas invite
a.
accidents.
Keep children and bystanders away while using this product. Distractions can
b.
cause you to lose control.
Personal safety
Stay alert, watch what you are doing and use common sense when using this
a.
product. Do not use this product while you are tired or under the inuence of
drugs, alcohol or medication. A moment of inattention while using this product
may result in serious personal injury.
Use safety equipment. Always wear eye protection. Safety equipment
b.
such non-skid safety shoes, hard hat, or heavy duty work gloves used for
appropriate conditions will reduce personal injuries.
Do not overreach. Keep proper footing and balance at all times. This
c.
enables better control of this product in unexpected situations.
Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
d.
clothing and gloves away from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
3.
Product use and care
Do not force this product. Use the correct product for your application. The
a.
correct product will do the job better and safer at the rate for which it was
designed.
Store this product out of the reach of children and do not allow people
b.
unfamiliar with the product or these instructions to operate the product. This
product could be dangerous in the hands of untrained users.
Maintain this product. Check for misalignment or binding of moving parts,
c.
breakage of parts and any other condition that may affect the product’s
operation. If damaged, have this product repaired before use. Many
accidents are caused by poorly maintained equipment.
Use this product in accordance with these instructions and in the manner
d.
intended for this particular type of product, taking into account the working
conditions and the work to be performed. Use of this product for operations
different from those intended could result in a hazardous situation.
Page 3SKU 96462 For technical questions, please call 1-800-444-3353.
Page 4
4.
Service
Have this product serviced by a qualied repair person using only identical
a.
replacement parts. This will ensure that the safety of the product is
maintained.
SPECIFIC SAFETY RULES
1.
2.
3.
4.
5.
6.
7.
8.
9.
This Trailer Sway Control Kit is designed for use only with Class III and Class IV
hitches.
This Trailer Sway Control Kit is NOT for use on trailers with surge brakes.
Larger trailers may require the use of two Sway Controls.
Maintain labels and nameplates on the Trailer Sway Control Kit. These carry
important safety information. If unreadable or missing, contact Harbor Freight
Tools for a replacement.
Secure the Spring Clips (4) before operating.
Wear ANSI-approved safety goggles during installation and use.
Always inspect the Trailer Sway Control Kit before each use. Do not use this
product if any parts are bent or damaged.
Be aware that the Sway Control may hit a vehicle’s rear bumper or trailer coupler
in an extreme jackknife position.
Only a certied, qualied welder should install this Trailer Sway Control Kit onto a
trailer.
10.
11.
Trailers should be loaded with heavy items on the oor of the trailer and in front
of the axle. The load should be balanced side to side. Tongue weight should be
10-15% of gross trailer weight for most trailers. Insufcient tongue weight or tail
heavy trailers can cause sway. Sway increases with speed. If sway continues,
stop the vehicle and inspect all equipment and trailer loading until the cause has
been determined and corrected. Short wheel base vehicles may induce sway
when towing a trailer.
The warnings, precautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS.
Page 4SKU 96462 For technical questions, please call 1-800-444-3353.
Page 5
SPECIFICATIONS
Sway Control Style Dual Friction
For use with Class III & Class IV hitches
Product Applications
Trailer Tongue Ball Plate
Size
Sway Control Size 20” Long x 2-1/2” Wide x 1-1/8” Thick
Construction
Capacity For GTW (Gross Trailer Weight) up to 6,000 lb.*
Net Weight 14.5 Pounds
* GTW 6,000 to 10,000 lb. need 2 Sway Control Kits installed.
The Trailer Sway Control Kit will t the following trailers offered by Harbor Freight Tools*.
Model 5002 BOAT TRAILER WITH 8” WHEELS AND TIRES
Model 94564 1740 LB. CAPACITY SUPER DUTY 48” X 96” UTILITY TRAILER
Model 93747 1500 LB. CAPACITY, 60” X 96” TRAILER
Model 42709 990 LB. CAPACITY FOLDABLE 48” X 96” UTILITY TRAILER
Model 42708 860 LB. CAPACITY 40” X 49” MINI UTILITY TRAILER
Model 90154 1175 LB. CAPACITY 48” X 96” FOLDABLE UTILITY TRAILER
Model 6464 1740 LB. CAPACITY SUPER DUTY 48” X 96” UTILITY TRAILER
May be installed on left or right side of trailer
Not for use on trailers with surge brakes
6-1/8” Long x 3” Wide x 0.2” Thick
Carbon steel with black powder coat / chrome nish / zinc plated
hardware & fasteners
*Installation requires professional welding.
UNPACKING
When unpacking, check to make sure that the item is intact and undamaged. If any
parts are missing or broken, please call Harbor Freight Tools at the number shown on the
cover of this manual as soon as possible.
INSTALLATION
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the
beginning of this manual, including all text under subheadings therein
before set-up or use of this product.
WARNING! Only a certied, qualied welder should install this Trailer Sway Control Kit.
Page 5SKU 96462 For technical questions, please call 1-800-444-3353.
Page 6
SWAY CONTROL BALL (13)
SWAY CONTROL BALL (13)
Note:
Most weight distributing ball mounts come equipped with a sway control ball
plate attached. If so, attach the Sway Control Ball (13) to the vehicle’s ball mount
using the hole provided. If no sway control ball hole is provided, weld the Sway
Control Ball Mount Bar (10) to the vehicle’s ball mount.
(See Figure A and Assy. Diagram Page 10)
1.
Measure 24” straight back from the center of the coupler to the right hand side of
the trailer frame to determine the location of the Mounting Plate (1). The Trailer
Tongue Ball (3) must be centered on the 24” measurement. NOTE: If installment
on the left side of the trailer is desired, measure 24” straight back from the center
of the coupler to the left hand side of the trailer frame to determine the location of
the Mounting Plate (1). (See Figure B and C on page 7, and Assy. Diagram)
2.
Use the mounting holes in the Mounting Plate (1) as a template with which to drill
eight 11/32” diameter holes in the trailer frame.
If the marked holes cannot be drilled properly, then the Trailer Tongue Ball
a.
must be welded directly onto the side of the trailer.
Otherwise, attach the Mounting Plate (1) and Trailer Tongue Ball (3) to the
b.
trailer frame, using the eight self-tapping Screws (2) provided.
WARNING! Make sure all welds are strong and capable of holding the tension placed
on them by the Sway Control unit before going on to the next step.
Page 6SKU 96462 For technical questions, please call 1-800-444-3353.
Page 7
Page 7SKU 96462 For technical questions, please call 1-800-444-3353.
Page 8
3.
For left hand installation, remove the Slide Bar (14), and reinstall it upside down.
(See photo above and Assy. Diagram.)
OPERATING INSTRUCTIONS
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the
beginning of this manual, including all text under subheadings therein
before set-up or use of this product.
1.
2.
3.
4.
5.
Hook up the trailer to the tow vehicle. CAUTION! Make sure to refer to your
trailer and vehicle “Owner Manuals” for proper hook up instructions.
Lubricate the threads of the ON/OFF Handle (6) with a drop of oil.
(See Assy. Diagram)
Attach the Socket on the Slide Bar (14) to the Sway Control Ball (13) on the
Sway Control Ball Mount Bar (10). Then secure in place, using a Spring Clip (4).
(See Assy. Diagram)
Turn the ON/OFF Handle (6) three turns counterclockwise to release tension.
(See Assy. Diagram)
Place the Socket on the Slide Bar (14) onto the Trailer Tongue Ball (3). Then
secure in place, using a Spring Clip (4). (See Figure F and Assy. Diagram)
6.
WARNING! Make sure that the Spring Clip (4) is closed and not bent open. The
Spring Clip (4) will fall out if it does not have proper tension. (See Figure F)
Page 8SKU 96462 For technical questions, please call 1-800-444-3353.
Page 9
7.
Turn the ON/OFF Handle (6) clockwise. Tighten rmly until the Handle is parallel
with the Inside Friction Plate (9). (See Figure G below)
8.
With a second person watching the Sway Control unit and trailer, slowly
back the trailer in both directions to a jackknife position and check that the
Sway Control unit does not hit the bumper or trailer frame and that it does not
become fully compressed or come apart. If any of these incidents occur when
jackknifed, the Sway Control unit must be removed when backing up the trailer.
NOTE: Road and weather conditions, loading and design of trailer as well
as power steering, wheel alignment, and the oscillation point of the tow
vehicle and trailer all affect towing characteristics.
9.
10.
11.
Starting with the factory preset tension, road test the Sway Control unit. If the
preset tension is not enough sway control, adjust the Brake Torsional Screw
(7) by turning it a 1/4 turn clockwise. Road test the trailer again and repeat if
necessary, until proper sway control is achieved. (See Figure G)
IMPORTANT: Larger or heavier or broad-sided trailers may require the use of
two Sway Control units. One Sway Control Kit can be used for GTW up to 6,000
lb. Any GTW heavier than 6,000 lb. and less than 10,000 lb. will require two
Sway Control Kits.
After a 1,000 mile break-in period, remove and clean the Slide Bar (14) using a
wire brush or steel wool. Then lubricate and re-install the Slide Bar. The Slide
Bar should then be cleaned every 10,000 miles. (See Assy. Diagram)
Page 9SKU 96462 For technical questions, please call 1-800-444-3353.
Page 10
MAINTENANCE AND SERVICING
WARNINGWARNING
1.
2.
3.
BEFORE EACH USE, inspect the general condition of the tool. Check for loose
screws, misalignment or binding of moving parts, cracked or broken parts, and
any other condition that may affect its safe operation.
AFTER USE, clean external surfaces of the Sway Control unit with a garden
hose. Then dry and lubricate all moving parts. Do not use solvents.
CAUTION! All maintenance, service, and repairs not mentioned in this manual
must only be performed by a qualied service technician.
Risk of serious personal injury. Keep hands, ngers,
and body safely away from the Sway Control unit before
performing any inspection or maintenance procedures.
Damaged equipment can fail, causing serious personal
injury. Do not use damaged equipment. If abnormal noise or
vibration occurs, have the problem corrected before further
use.
Cleaning, maintenance, and lubrication
Troubleshooting
Problem Possible Causes Probable Solutions
Sway Control unit
contacts trailer
frame or tow vehicle
bumper when
backing up in a
jackknife position.
Not enough sway
control.
Road and weather conditions,
loading and design of trailer, power
steering, wheel alignment, and
other factors can affect towing
characteristics.
Sway control tension insufcient. Adjust Brake Torsional Screw 1/4 turn
Disconnect Sway Control unit from tow
vehicle when backing up.
clockwise. Repeat if necessary until
proper sway control is achieved. Larger
or heavier or broad-sided trailers may
require the use of two Sway Control
units.
Page 10SKU 96462 For technical questions, please call 1-800-444-3353.
Page 11
PARTS LIST & ASSEMBLY DIAGRAM
Part Description Q’ty
1 Mounting Plate 1
2 Screw 8
3 Trailer Tongue Ball 1
4 Spring Clip 2
6 Handle 1
7 Brake Torsional Screw 1
8 Plate 1
Part Description Q’ty
9 Inside Friction Plate 2
10 Sway Control Ball Mount Bar 1
11 Nut 1
12 Spring Lock Washer 1
13 Sway Control Ball 1
14 Slide Bar 1
2
Page 11SKU 96462 For technical questions, please call 1-800-444-3353.
Page 12
LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this product
is free from defects in materials and workmanship for the period of 90 days from the date
of purchase. This warranty does not apply to damage due directly or indirectly, to misuse,
abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity,
improper installation, normal wear and tear, or to lack of maintenance. We shall in no event
be liable for death, injuries to persons or property, or for incidental, contingent, special
or consequential damages arising from the use of our product. Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation
of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint
must accompany the merchandise. If our inspection veries the defect, we will either
repair or replace the product at our election or we may elect to refund the purchase price
if we cannot readily and quickly provide you with a replacement. We will return repaired
products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning
the product.
This warranty gives you specic legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE
UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
Page 12SKU 96462 For technical questions, please call 1-800-444-3353.
Loading...