Harbor Freight Tools 96451 User Manual
INFRARED THERMOMETER
Model
96451
OPERATING INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright© 2007 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
SAVE THIS MANUAL
Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number in
the back of the manual near the assembly diagram (or month and year of purchase if
product has no number). Keep this manual and the receipt in a safe and dry place for
future reference.
WARNING! Read all instructions
Failure to follow all instructions listed below may result in serious injury.
Work area safety
1.
2.
1.
2.
1.
2.
Keep children and bystanders away while operating. Distractions can
cause you to lose control.
Keep work area clean and well lit. Cluttered or dark areas invite accidents.
Personal safety
Wear ANSI-approved safety goggles. Use eye protection. Never point
laser directly into the eyes of a person or animal. Do not point laser on, or
indirectly off, reective surfaces such as stainless steel or aluminum.
Stay alert and use common sense when operating. Do not use when tired or
under the inuence of drugs, alcohol or medication.
Product use and care
This product is not a toy. Keep it out of reach of children.
Use the product in accordance with these instructions and in the manner
intended for the particular type of product, taking into account the working
conditions and the work to be performed. Use of the product for operations
different from those intended could result in a hazardous situation.
3.
4.
1.
Not for medical use.
The warnings, precautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
Service
Have product serviced by a qualied repair person using only identical
replacement parts. This will ensure that the safety of the product is maintained.
Page 2SKU 96451 For technical questions, please call 1-800-444-3353.
2.
AVOID EXPOSURE – Laser light is emitted from this aperture.
DANGER
LASER LIGHT
AVOID DIRECT EYE EXPOSURE
Max. Output: <5 mW, Wavelength: 630-660 nm
CLASS IIIa LASER PRODUCT
This product complies with 21 CFR 1040.10 and 1040.11
CEN-TECH, 3491 Mission Oaks Blvd., Camarillo, CA, USA, 93011
WARNING
To prevent serious injury:
Do not use for medical purposes.
Wear ANSI-approved safety goggles when replacing battery.
1.
2.
Date:_____, _________________DO NOT REMOVE.
Maintain labels and nameplates on the product. These carry important safety
information. If unreadable or missing, contact Harbor Freight Tools for a
replacement.
SAVE THESE INSTRUCTIONS.
SPECIFICATIONS
Measurement Range
Accuracy
Response Time 500 mSec
Distance to Spot Size 8:1
Battery Requirements 9V
-4° F to 968° F
(-20° C to 520° C)
± 4° F below 212° F
± 2% reading above 212° F
UNPACKING
When unpacking, check to make sure that the item is intact and undamaged. If any
parts are missing or broken, please call Harbor Freight Tools at the number shown on the
cover of this manual as soon as possible.
OPERATING INSTRUCTIONS
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the
beginning of this manual including all text under subheadings therein
before set up or use of this product.
Note: Do not expose this product to strong electromagnetic elds, such as those
generated by an arc welder, induction heater, etc. Allow the unit 30 minutes to
adjust, before use, when introduced to signicant temperature changes.
1.
2.
3.
4.
5.
Remove the battery cover and insert a 9V battery into the unit, paying attention to
polarity. Replace battery cover.
Push the “Laser ON/OFF” button to activate unit.
Pull and hold down trigger to turn unit on. When the Trigger is released, the unit
will beep and display the last temperature measured for 15 seconds.
To locate a “hot spot” move laser up and down in an area to see temperature
variance.
Non-reective surfaces will yield a more accurate reading than reective
surfaces. Duct tape (not included) can be applied to reective surfaces in order
REV 07j
Page 3SKU 96451 For technical questions, please call 1-800-444-3353.
Loading...