Harbor Freight Tools 95203 Product manual
CARPENTER’S 6” VISE
WITH CLAMP
95203
OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
Copyright © 2006 by Harbor Freight Tools
manual or any artwork contained herein may be reproduced in any shape or form without
the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353
.
All rights reserved. No portion of this
SPECIFICATIONS
ITEM DESCRIPTION
Materials Steel Frame and Jaws with an enclosed Leadscrew
Finish Dark Blue Vise with Chrome Adjusters - Black Bushing
Vise Dimensions 7-3/4”L X 6-1/8”W X 6-1/2”H
Mounting Holes 1/4” Diameter (2X)
Jaw Opening 5-1/4” Max. X 2” Throat Depth
Jaw Material High Carbon Steel
New Weight 5.85 Lbs.
SAVE THIS MANUAL
You will ne ed th e manua l for the saf ety wa rnin gs and preca uti ons ,
operating and maintenance procedures, parts list and diagram. Keep your invoice
with this manual. Write the invoice number on the inside of the front cover. Keep
the manual and invoice in a safe and dry place for future reference.
SAFETY WARNINGS AND PRECAUTIONS
1. KEEP PRODUCT USAGE AREA CLEAN. Cluttered areas invite injuries.
2. KEEP CHILDREN AWAY FROM PRODUCT USAGE AREA. Do not allow children
to handle this product.
3. DO NOT USE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL OR
DRUGS. Read warning labels on prescriptions to determine if your judgement or
reflexes are impaired while taking drugs. If there is any doubt, do not use this
product.
4. USE EYE PROTECTION. Wear ANSI-approved safety impact goggles. Goggles
are available from Harbor Freight Tools.
5. DRESS SAFELY. Do not wear loose clothing or jewelry as they can become caught
in moving parts. Wear a protective hair covering to prevent long hair from become ing caught in the moving parts.
6. DO NOT OVERREACH. Keep proper footing and balance at all times. Never lean on
or try to pull on the Vise.
7. STAY ALERT. Watch what you are doing at all times. Use common sense. Do not
operate this product when you are tired or distracted from the job at hand.
SKU 95203 For technical questions please call 1-800-444-3353. Page 2
8. CHECK FOR DAMAGED PARTS. Before using this product, carefully check that it
will operate properly and perform its intended function. Check for damaged parts and
any other conditions that may affect its operation. Replace or repair damaged or worn
parts immediately.
9. MAINTAIN PRODUCT WITH CARE. Keep this product clean and dry, and moving parts
lightly lubricated for better performance. Keep the Handle dry, clean and free from oil,
grease, and solvents.
10. USE THE RIGHT PRODUCT FOR THE RIGHT JOB. Do not attempt to force a small
tool or attachment to do the work of a larger industrial tool. There are certain applications
for which this tool was designed. It will do the job better and more safely at the rate
for which it was intended. Do not modify this tool and do not use this tool for any
purpose other than which it was intended. Use for intended purpose only.
UNPACKING
When unpacking, check to make sure all parts shown on the Parts Illustration (page 6) are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on
the cover of this manual as soon as possible.
NOTE: Please refer to the parts listed on page 7 of this manual. Use 3/16” diameter bolts
of the appropriate length when mounting your Vise. Bolts, Lock Washers and Nuts for mounting are NOT provided. You can mount the Vise or use it in a portable manner, depending
on what product you are working on.
MOUNTING THE CARPENTER’S VISE
1. Use the two mounting holes on the Vise Back Jaw with Clamp (1) as a template. Set the
Vise flat on the workbench and, with a pencil, mark the points at which to fasten the Vise
onto the workbench. Set the Vise aside.
2. Drill two holes of the appropriate size (where previously marked with a pencil) through
the top of the workbench. Caution: Before drilling holes, check for hidden electrical
wires or cords in drilling path.
3. Carefully set the Back Jaw (1) of the Vise with the two Mounting Holes corresponding
to the holes previously drilled through the top of the workbench. See Figure 1 next
page.
4. Insert two 1/4” diameter hardened steel bolts (not provided), of the appropriate
length, downward through the Back Jaw (1) and the drilled holes in the workbench.
The length of hardened steel mounting bolts will vary, depending on the thickness of
workbench the Vise is to be attached to.
SKU 95203 For technical questions please call 1-800-444-3353. Page 3
Loading...