Harbor Freight Tools 95153 User Manual
OUTDOOR IMITATION CAMERA
Model
95153
SET UP INSTRUCTIONS
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight
Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual
product may differ slightly from the product described herein. Tools required for assembly and service may not
be included.
Revised Manual 07b, 08a, 09k
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
For technical questions or replacement parts, please call 1-800-444-3353.
SPECIFICATIONS
Batteries Required 2 “AA” Batteries (sold separately)
Overall Dimensions 4-1/8” X 11-3/4” L X 4-5/16” H
Dimensions
Weight 2 lb.
Features 0-90° Up or Down Tilt, Continuous Blinking LED
Bracket - 7” High
Base - 3-1/2” Diameter
Save This Manual
You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with
this manual. Write the invoice number on the inside of the front cover. Keep the manual and
invoice in a safe and dry place for future reference.
SAFETY WARNINGS AND PRECAUTIONS
WARNING: When using this product, basic safety precautions should always be followed
to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
Keep work area clean and well lit. 1. Cluttered areas invite injuries.
Observe work area conditions. 2. Do not use the Imitation Camera in damp or wet loca-
tions. Don’t expose to rain. Do not use electrically powered products in the presence
of flammable gases or liquids.
Keep children away. 3. Children must never be allowed in the work area. Mount the
Imitation camera out of children’s reach. This product is not a toy.
Use the right product for the job. 4. Do not modify this product and do not use this
product for a purpose for which it was not intended.
Dress properly. 5. Protective, electrically nonconductive clothes and nonskid footwear
are recommended when working. Wear restrictive hair covering to contain long hair.
Always wear ANSI-approved impact safety goggles and heavy-duty work gloves 6.
during installation or service.
Stay alert. 7. Watch what you are doing, use common sense. Do not install the Imitation
Camera when you are tired.
Check for damaged parts. 8. Before installing the Imitation Camera, any part that ap-
pears damaged should be carefully checked to determine that it will operate properly
and perform its intended function. Check for any broken parts or mounting fixtures and
any other condition that may affect proper function. Any part that is damaged should
be properly repaired or replaced by a qualified technician.
For technical questions, please call 1-800-444-3353
Page 2SKU 95153
Replacement parts and accessories. 9. When servicing, use only identical replacement
parts. Use of any other parts will void the warranty. Only use accessories intended for
use with this product. Approved accessories are available from Harbor Freight Tools.
Do not install the Imitation Camera if under the influence of alcohol or drugs. 10.
Read warning labels if taking prescription medicine to determine if your judgment or
reflexes are impaired while taking drugs. If there is any doubt, do not install the unit.
For your safety, service and maintenance should be performed regularly by a 11.
qualified technician.
The warnings, precautions, and instructions discussed in this instruction manual 12.
cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS.
UNPACKING
When unpacking, check to make sure that the product is intact and undamaged. If any parts
are missing or broken, please call Harbor Freight Tools at the number on the cover of this
manual as soon as possible.
For technical questions, please call 1-800-444-3353
Page 3SKU 95153
Loading...