Harbor Freight Tools 95141 User Manual

HEAVY DUTY TWIN HAMMER

3/4” IMPACT WRENCH

Model 95141

ASSEMBLY AND OPERATING INSTRUCTIONS

Due to continuing improvements, actual product may differ slightly from the product described herein.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at: http://www.harborfreight.com

TO PREVENT SERIOUS INJURY,

READ AND UNDERSTAND ALL WARNINGS

without the express written consent of Harbor Freight Tools.

For technical questions, please call 1-800-444-3353.

AND INSTRUCTIONS BEFORE USE.

PRODUCT SPECIFICATIONS

Drive Size 3/4” Square Drive Impact Mechanism Twin Hammer Maximum RPM 4300 Anvil Retainer Type Hog Ring Maximum Torque 1300 Ft./Lb. Blows Per Minute 960 Air Inlet Size 3/8”-18 NPT Recommended Hose Size 1/2” Inside Diameter (Not Included) Air Consumption 9.3 SCFM @ 90 PSI Overall Dimensions 12.2” Long x 11/4” Wide x 4.7” High Net Weight 12.5 Lb.

Item Description

SAVE THIS MANUAL

You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep this manual and invoice in a safe and dry place for future reference.

UNPACKING

When unpacking, check to make sure that all the parts and accessories listed on page 8 are included, and the product is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible.

SAFETY WARNINGS AND PRECAUTIONS

2. Keep work area clean. Cluttered areas invite accidents.

3. Stay within air pressure capacity. Never operate the Impact Wrench above

90 PSI.

WARNING! Use eye and hearing protection. Always wear ANSI

approved safety impact goggles when using this Impact Wrench. Also, wear ANSI approved hearing protection. Other people in the work area must also wear appropriate ANSI approved safety equipment.

4. Observe work area conditions. Keep work area well lit. Do not use pneumatic

SKU 95141 For technical questions, please call 1-800-444-3353 PAGE 2

tools in the presence of flammable gases or liquids.

5. Keep children away. Children must never be allowed in the work area. Do not

let them handle machines, tools, extension cords, or air hoses.

6. Store idle equipment. When not in use, tools must be stored in a dry location

to inhibit rust. Always lock up tools and keep out of reach of children.

7. Use the right tool for the job. Do not attempt to force a small tool or attachment

to do the work of a larger industrial tool. There are certain applications for which this tool was designed. It will do the job better and more safely at the rate for which it was intended. Do not modify this tool, and do not use this tool for a purpose for which it was not intended.

8. Dress properly. Do not wear loose clothing or jewelry as they can be caught in

moving parts. Protective, electrically non-conductive clothes and non-skid footwear are recommended when working. Wear restrictive hair covering to contain long hair.

9. Do not overreach. Keep proper footing and balance at all times. Do not reach

over or across running tools or air hoses.

10. Disconnect air hose and release any built-up air pressure. Never service the

Impact Wrench or disassemble with the air hose attached. Always release any built-up air even after disconnecting hose. Disconnect the Impact Wrench when not in use.

11. Avoid unintential starting. Be sure the Trigger (27) is in the OFF position

when not in use and before plugging in. Do not carry any tool with your finger on the Trigger, whether it is attached to an air source or not.

12. Stay alert. Watch what you are doing. Use common sense. Do not operate any

tool when you are tired or distracted.

13. Check for damaged parts. Before using any tool, any part that appears

damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts, any broken parts, and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. Do not use the tool if the Trigger does not operate properly.

14. Replacement parts and accessories. This product is to be repaired and

serviced only by a qualified technician. When this product is serviced, only identical replacement parts should be used. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools.

SKU 95141 For technical questions, please call 1-800-444-3353 PAGE 3

+ 6 hidden pages