Page 1
5 Gallon Pail Pump
Item 95068
INSTRUCTIONS AND
PRECAUTIONS
Copyright© 2006 by Harbor Freight Tools®.
All rights reserved. No portion of this document
or any artwork contained herein may be
reproduced in any shape or form without the
express written consent of Harbor Freight
Tools. Diagrams within this document may
not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly
from the product described herein. Tools required
for assembly and service may not be included.
For technical questions or replacement
parts, please call 1‑800‑444‑3353.
Specications
Visit our website at:
http://www.harborfreight.com
Read this material before
using this product.
Failure to do so can result
in serious injury.
SAVE THIS MANUAL.
When unpacking, make sure
that the product is intact and
undamaged.
If any parts are missing or broken,
please call 1‑800‑444‑3353
as soon as possible.
Construction Black PP T‑Handle
Overall Dimensions 19.3 IN. L X 2.6 IN. D.
Pump Output Spout 8 IN. L X 1/2 IN. D.
Delivery Hose Clear vinyl with
Spout Hole 9/32 IN. D.
Output per Pump approximately 60 ml
Features
with molded nger grip,
aluminum spout; Ground
Shaft with O‑ring seals
coil spring; 47 IN.
L X 5/8 IN. D.
Head swivels 360
degrees; includes Bung
Adapter and Vinyl Hose
Important Safety Information
1. For use with oil only. Do not use with
water. Do not use with corrosive
liquids. Do not use with gasoline.
2. Wear ANSI‑approved safety goggles
and heavy‑duty work gloves during use.
3. Keep area clean and well lit.
4. Do not operate when tired
or when under the inuence
of drugs or medication.
Manual Revised 11d
Page 2
5. This product is not a toy. Do not allow
children to play with or near this item.
6. Use as intended only.
7. The container (not included)
that the oil will be siphoned into
must be set onto a at and level
surface capable of supporting the
container and the transferred oil.
8. Do not pump used, dirty oil.
9. Do not leave pump unattended
while operating.
10. Do not use near open ame
or heat sources.
11. Use only on a at surface
capable of supporting the Pail
Pump and its contents.
12. Know and obey city and state laws
for proper disposal of oil. Dispose
of oil properly in accordance with
all local laws and regulations.
13. Inspect before every use; do not
use if parts are loose or damaged.
14. Maintain product labels and
nameplates. These carry important
safety information. If unreadable
or missing, contact Harbor Freight
Tools for a replacement.
Operating Instructions
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of
this document including
all text under subheadings
therein before set up or
use of this product.
Note: Bottom Cover (5) has an adapter
to attach a hose (not included).
Handle (1)
Head Cap
(3)
Upper
Cover (4)
Bottom
Cover (5)
Outer
Tube (6)
Figure 1
1.
Insert the Outer Tube (6) into the
container of oil through the opening
on the cover. Set the Head Cap (3),
Upper Cover (4) and Bottom Cover
(5) with adapter to the bung of the
pail‑see Figure 1. Thread into place.
2. Run the PVC Hose (12) into a container
(not included) in which to siphon the
oil. Make certain that the container
is large enough to contain the entire
emptied contents of the pail.
Page 2 For technical questions, please call 1‑800‑444‑3353. SKU 95068
Page 3
Pull Rod (2)
PVC Hose (12)
Figure 2
3.
Make certain that the Mouth (11) of
the Outer Tube is submerged into
the oil you are planning to transfer.
Pump the Pull Rod (2) up and down
using the Handle (1) ‑ see Figure 2.
4. When the transfer is nished, pump
the Pail Pump fully until it runs dry.
5. Remove the Pail Pump from
the pail and wipe it dry.
6. Dispose of the oil properly. Know
and obey city and state laws for
proper disposal of oil. Dispose
of oil properly in accordance with
all local laws and regulations.
Nozzle (15)
Maintenance
1. Regularly clean the exposed parts
of the Pail Pump after each use.
Clean Pump with warm water
and a mild household detergent.
Dry with a clean cloth.
2. Periodically use a light oil lubricant
on the Handle assembly.
3. Store in a dry place out of
the reach of children.
4. Check all hoses and connections
for damage, leaks and kinks in the
line. Check hoses for blockage.
Do not use a damaged Pail Pump.
Replacement parts are available
through Harbor Freight Tools.
Troubleshooting
Pump does not draw up oil.
a. Make certain Upper Cover and
Bottom Cover (5) are securely
attached to the bung of the pail.
b. Make certain Nozzle (15) is
free of dirt and debris.
c. Make certain Outer Tube (6) Mouth
(11) is free of dirt and debris.
d. Check that Mouth (11) is submerged
into uid to be pumped.
e. Fluid to be pumped may be too
thick. Be certain to pump only light
weight oils to gear oils.
Page 3For technical questions, please call 1‑800‑444‑3353.SKU 95068
Page 4
Parts List and Assembly Diagram
Part Description Qty
1 Handle 1
2 Pull Rod 1
3 Head Cap 1
4 Upper Cover 1
5 Bottom Cover 1
6 Outer Tube 1
7 Inner Tube 1
8 Seal Cover 1
9 O‑Ring 1
3 4 5 6
2
1
Part Description Qty
10 Steel Ball 1
11 Mouth 1
12 PVC Hose 1
13 Spring 1
14 Spring 1
15 Nozzle 1
16 Steel Ball 1
17 Spring 1
7 10
9 11
8
13
14
12
Note: Some parts are listed and shown for illustration purposes
only, and are not available individually as replacement parts.
Record Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
17
15
16
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST IN THIS
DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE
OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/
OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY
THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR
HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR
ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Loading...