Harbor Freight Tools 95028 User Manual

3” COMPOSITE AIR CUT-OFF TOOL

®

95028

ASSEMBLY AND OPERATING

INSTRUCTIONS

Due to continuing improvements, actual product may differ slightly from the product described herein.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

TO PREVENT SERIOUS INJURY,

READ AND UNDERSTAND ALL WARNINGS

AND INSTRUCTIONS BEFORE USE.

Copyright© 2006 by Harbor Freight Tools® . All rights reserved. No portion of this manual or any
artwork contained herein may be reproduced in any shape or form without the express written
consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353.

Specifications

Maximum RPM 20,000 RPM at 90 PSI
Maximum Air Pressure 90 PSI
Air Consumption 5 CFM at 90 PSI
Air Inlet Diameter 1/4” - 18 NPT (female inlet)
Spindle Diameter 3/8”
Accessories 3” Diameter Cut-Off Wheel

14 mm Spanner Wrench

5 mm Hex Key
Overall Dimensions 3-3/8” D X 7-3/8” L X 3” H
Weight 1.8 lbs.

Save This Manual

You will need the manual for the safety warnings and precautions, assembly instructions,
operating and maintenance procedures, parts list and diagram. Keep your invoice with this
manual. Write the invoice number on the inside of the front cover. Keep the manual and
invoice in a safe and dry place for future reference.

Safety Warnings and Precautions

WARNING: When using tool, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.

Read all instructions before using this tool!

1. Keep work area clean. Cluttered areas invite injuries.

2. Do not operate pneumatic tools in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust. Pneumatic tools create sparks
which may ignite flammables..

3. Keep children away. Children must never be allowed in the work area. Do not let
them handle machines, tools, extension cords, or air hoses.

4. Store idle equipment. When not in use, tools must be stored in a dry location to
inhibit rust. Always lock up tools and keep out of reach of children.

5. Use the right tool for the job. Do not attempt to force a small tool or attachment
to do the work of a larger industrial tool. There are certain applications for which this
tool was designed. It will do the job better and more safely at the rate for which it was
intended. Do not modify this tool and do not use this tool for a purpose for which it
was not intended.

For technical questions, please call 1-800-444-3353

Page 2SKU 95028

6. Stay alert. Watch what you are doing and use common sense when operating a

pneumatic tool. Do not use a pneumatic tool while tired or under the influence
of drugs, alcohol or medication. Doing so may result in serious personal injury.

7. Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose clothes,

jewelry, or long hair can be caught in moving parts.

8. Avoid accidental starting. Be sure the Trigger Lever (14) is off before connecting
to the air supply. Carrying pneumatic tools with your finger on the Trigger, or
connecting pneumatic tools to the air supply with the Trigger on, invites accidents.

9. Remove adjusting keys or wrenches before turning on the tool. A wrench or a key
that is left attached to a rotating part of the tool may result in personal injury.

10. Do not overreach. Keep proper footing and balance at all times. Proper footing
and balance enables better control and of the toll in unexpected situations.

11. Use safety equipment. Always wear ANSI-approved safety glasses under-

neath a full face shield, and hearing protection.

12. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use accessories
intended for use with this tool. Approved accessories are available from Harbor Freight
Tools.

13. Do not operate tool if under the influence of alcohol or drugs. Read warning
labels if taking prescription medicine to determine if your judgement or reflexes are
impaired while taking drugs. If there is any doubt, do not operate the Cut-Off Tool.

14. Use proper size and type extension cord. If an extension cord is required, it must
be of the proper size and type to supply the correct current to the compressor without
heating up. Otherwise, the extension cord could melt and catch fire, or cause electrical
damage to the compressor. Check your air compressor’s manual for the appropriate
size cord.

15. Maintenance. For your safety, maintenance should be performed regularly by a
qualified technician.

16. Compressed air only. Use clean, dry regulated, compressed air at 90 PSI. Never

use oxygen, carbon dioxide, combustible gases, or any other bottled gas as a power
source for this tool.

17. When connecting to the air supply: Prior to each use, if an automatic oiler is not
used, add two drops of air tool oil (not included) into the Air Inlet (13) fitting of the Cut­Off Tool.

18. Always disconnect the Cut-Off Tool from its compressed air supply source, and

squeeze the Trigger Lever (14) to release all compressed air in the tool before
performing any maintenance or services.

Note: Performance of the compressor (if powered by line voltage) may vary depending on

variations in local line voltage. Extension cord usage may also affect tool performance.

For technical questions, please call 1-800-444-3353

Page 3SKU 95028