Harbor Freight Tools 91092 User Manual

ADIRONDACK ROCKER

91092

ASSEMBLY AND OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our W eb site at http://www.harborfreight.com

Copyright © 2004 by Harbor Freight Tools®. All rights reserved. No por tion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353

Specifications

Comfortable Natural Fir Wood Adirondack Rocking Chair

Overall Dimension 29-1/2”L x 37”W x 36-1/4”H Back Seat Height 8-3/4”
Seat Area 19”D x 20”W Back Slat Length 32”
Arm Rest 30-7/8”L x 4-1/2”W Front Seat Height 11-1/2”
Back Rest 30-1/2”L x 17-3/8”W Net Weight 22 Lbs.
Rocker 37”L
Weight Capacity 250 Lbs.

Save This Manual

You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram. K eep
your inv oice with this manual. Write the invoice number on the inside of the front
cover. Keep the manual and in v oice in a safe and dry place for future reference .

Safety Warnings and Precautions

WARNING: When assembling and using this item, basic safety precautions
should always be followed to reduce the risk of personal injury and damage
to equipment.

Read all instructions before beginning assembly!

1. Keep assembly area clean. Cluttered areas invite injuries.

2. Observe work area conditions. Do not use machines or power tools in
damp or wet locations. Keep work area well lighted. Do not use electrically
powered tools in the presence of flammable gases or liquids.

3. Keep children away. Children must never be allowed in the assemb ly area.
Do not let them handle machines, tools, or extension cords. Avoid small
fingers being pinched. They could be accidently pushed between slats.
Avoid rocking over small children’s hands or feet and even pet’s tails when
sitting in the chair. Children should be supervised closely when using this
product.

4. Do not exceed weight capacity of this chair. To do so may cause
personal injury or property damage. Rocking too hard could cause tipping of
chair and injury. Do not use Rocker near pool, pond, spa or water source;
tipping of rocker could cause injury.

5. Use the right chair for the job. Do not modify this chair and do not use this
chair for a purpose for which it was not intended.

6. Do not overreach. K eep proper f ooting and balance during assembly.

SKU 91092

SKU 90849 Page 2

7. Stay alert. Watch what you are doing, use common sense during assembly,
and use of this chair.

8. Use eye and ear protection. Always wear ANSI approved impact safety
goggles during assembly.

9. Take caution as some woods contain preservatives such as copper
chromium arsenate (CCA) which can be toxic. When handling these
materials extra care should be taken to avoid inhalation and minimize skin
contact.

10. Check for damaged parts. Before using this chair, any part that appears
damaged should be carefully checked to determine that it will operate properly
and perform its intended function. Any part that is damaged should be properly
repaired or replaced.

11. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty.

12. Do not assemble this chair if under the influence of alcohol or drugs.
Read warning labels on prescriptions to determine if your judgment or reflexes
are impaired while taking drugs. If there is any doubt, do not proceed with
assembly.

13. Maintenance. F or your saf ety , service and maintenance should be performed
regularly . Check the alignment of all parts, and check the tightness of all
fasteners.

Warning: The warnings, cautions, and instructions discussed in this
instruction manual cannot cover all possible conditions and situations
that may occur . It must be understood by the operator that common
sense and caution are factors which cannot be built into this product,
but must be supplied by the operator.

Unpacking

When unpacking, check to make sure the following parts are included.

1 Back 1 Back Brace
1 Seat 10 Wood Screws
2 Front Legs 10 55mm Bolts with nut and washer
2 Back Supports 2 65mm Bolts with nut and washer
2 Arms 1 Owner’s Manual

2 Rockers 2 50mm Bolt with Nut and washer

4 80mm Bolt with nut and washer

If any parts are missing or broken, please call Harbor Freight Tools at the number
on the cover of this manual, or contact your local Harbor Freight retailer.

SKU 90849 Page 3

SKU 91092

Assembly Drawing

C1

B

D

I

Step 1

Attach the front end of B to C1 & C2

F

with 6 bolts, washers and nuts (I).

Step 2

Attach F (right and left) with C1 and C2.
using 4 bolts, washers and nuts (I). Attach
D (right and left) to B (seat, back end) and
F using 4 bolts, washers and nuts (L).

D

F

L

G

A

Step 3

Connecting G with the back of A, using
2 bolts, washers & nuts (K).

Step 4

Attach A with D & G, using 4 screws (H).
Attach A with B, using 2 screws (H).

C2

C1

Step 5

Attach E1 and E2 to D, using 2 bolts,
washers and nuts (J). Attach E1 to C1
with screws (H). Repeat with E2 to C2
with (H).

SKU 90849 Page 4

SKU 91092

Completed. Make sure all screws, nuts and
bolts are tightened and in place. Before using,
test the Rocker by rocking it back and f orth
and being sure it is safe to operate.

Maintenance

1. This chair is made of natural Fir wood. This beautiful material will naturally
weather over time , especially if used outdoors. You can manage the speed
and extent of this weathering by controlling the environment in which the chair
is used and stored, as well as any coatings you ma y apply.

2. Leaving the chair outside exposed to weather, especially direct sun, rain and
salt air, will speed the w eathering process. This can be slowed by remo ving
the chair from these conditions, or covering it with a suitable cov er .

3. You may wish to stain, varnish or paint the chair . If so, follow the instructions
supplied with these coatings.

4. Occasionally wash the chair with a garden hose or pressure sprayer to
remove accumulated dust or dirt. Wipe down or blow off any remaining water
left on the chair after washing.

5. Periodically (perhaps once per year), recheck the tightness of all fasteners.
Normal usage of the chair and weathering of the wood may cause fasteners
to loosen. If fasteners can not be tightened, use wood glue or some other
appropriate bonding material to ensure that fasteners remain tight.

SKU 90849 Page 5

SKU 91092

Parts List

Back Seat Left Front Leg

Right Front Leg Back Support Left Arm

Right Arm Rocker Back Brace

Screw 55mm Bolt 65mm Bolt

50mm Bolt 80mm Bolt

with Washer and Nut with Washer and Nut

with Washer and Nut with Washer and Nut

NOTE: Some parts are listed and shown for illustration purposes only and are not
available individually as replacement parts.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER
NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO
THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO TH E
PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE
PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THat ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS
OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

SKU 90849 Page 6

SKU 91092