Page 1
91090 91091
WHITE PAINTED
ADIRONDACK
CHAIR
ASSEMBLY AND OPERATING INSTRUCTIONS
VARNISHED
ADIRONDACK
CHAIR
91091 Pictured
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www .harborfreight.com
Copyright© 2004 by Harbor F reight T ools®. All rights reserved.
No portion of this manual or any artwork contained herein may be
reproduced in any shape or form without the express written consent
of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Page 2
Specifications
SKU 91090
Comfortable White-Painted Fir
wood Adirondack chair .
Dimensions:
Overall: 33”L x 36”W x 37”H Back Seat Height: 10”
Seat Area:18-1/2”D x 22”W Back Slat Length: 32”
Arm Rest:31-1/4”L x 5-1/8”W Front Legs: 21”L x 3”W x 7/8”
Front Seat Height: 15” Side Legs: 35-1/2”L
Weight: 20 lbs. Weight Capacity: 250 lbs.
Comfortable V arnished Fir
SKU 91091
wood Adirondack chair .
Save This Manual
Y ou will need the man ual for the safety w arnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram. Keep
your invoice with this manual. Write the invoice number on the inside of the front
cover . Keep the manual and inv oice in a saf e and dry place for future ref erence.
Safety Warnings and Precautions
WARNING: When assembling this item, basic safety precautions should always
be followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before beginning assembly!
1. Keep assembly area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use machines or power tools in
damp or wet locations. Keep work area well lighted. Do not use electrically
powered tools in the presence of flammable gases or liquids.
3. Keep children away . Children must never be allowed in the assemb ly area.
Do not let them handle machines, tools, or extension cords.
4. Do not exceed weight capacity of this chair. To do so may cause
personal injury or property damage.
5. Use the right chair for the job. Do not modify this chair and do not use this
chair for a purpose for which it was not intended.
6. Do not overreach. K eep proper footing and balance during assemb ly.
7. Stay alert. W atch what you are doing, use common sense during assembly
and use of this chair.
SKU 91090-91091 Page 2
Page 3
8. Use eye and ear protection. Always wear ANSI approved impact safety
goggles during assembly . Wear a full f ace shield if y ou are producing wood
chips. W ear an ANSI approved dust mask or respirator when working around
wood, and chemical dusts and mists.
9. T ake caution as some woods contain preserv atives such as copper
chromium arsenate (CCA) which can be toxic. When cutting these
materials extra care should be taken to av oid inhalation and minimiz e skin
contact.
10. Check for damaged parts. Bef ore using this chair , any part that appears
damaged should be carefully checked to determine that it will operate properly
and perform its intended function. Any part that is damaged should be properly
repaired or replaced.
11. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use
accessories intended for use with this item. Approved accessories are
available from Harbor F reight T ools.
12. Do not assemble this chair if under the influence of alcohol or drugs.
Read warning labels on prescriptions to determine if your judgment or reflexes
are impaired while taking drugs. If there is any doubt, do not proceed with
assembly.
13. Maintenance. F or your saf ety , service and maintenance should be performed
regularly . Check the alignment of all parts, and check the tightness of all
fasteners.
Warning: The warnings, cautions, and instructions discussed in this
instruction manual cannot cover all possible conditions and situations
that may occur . It must be understood by the operator that common
sense and caution are factors which cannot be built into this product,
but must be supplied by the operator.
Unpacking
When unpacking, check to make sure the following parts are included.
1 Back 1 Front Support
1 Seat 14 Wood Screws
2 Front Legs 10 55mm Bolts with nut and washer
2 Back Supports 2 65mm Bolts with nut and washer
2 Arms 1 Owner’s Manual
If any parts are missing or broken, please call Harbor Freight Tools at the number
on the cover of this manual, or contact y our local Harbor F reight retailer .
SKU 91090-91091 Page 3
Page 4
Assembly
Carefully unpack the parts and check for damaged or missing parts.
1. Attach Left Front Leg (C1) and Right Front Leg (C2) to Seat (B) using 3 Bolts
(H) per side. Use the included washers and nuts to tighten.
2. Attach both Back Supports (D) to the inner sides of the Seat (B) using 2 Bolts
(H) per side. Tighten using the included washers and nuts.
3. Attach the Left Arm (E1) and Right Arm (E2) to the Front Legs (C1, C2) using
2 Wood Screws (G) per side. Attach the Arms (E1, E2) to the Back Supports
(D) using 1 Long Bolt (I) per side. Tighten the bolts using included washers
and nuts.
4. Attach the Back (A) to Seat (B) and Back Supports (D) using a total of 6
Wood Screws (G).
5. Attach the Front Support (F) to the Front Legs (C1, C2) using 2 Wood Screws
(G) per side.
6. Recheck the alignment of all parts, and recheck the tightness of all fasteners.
7. Set up the chair on a flat, level location. Do not exceed load capacity of 250 lbs.
Maintenance
1. This chair is made of natural Fir wood. This beautiful material will naturally
weather over time , especially if used outdoors. You can manage the speed
and extent of this weathering by controlling the environment in which the chair
is used and stored, as well as any coatings you ma y apply.
2. Leaving the chair outside exposed to w eather, especially direct sun, rain and
salt air, will speed the w eathering process. This can be slowed by remo ving
the chair from these conditions, or covering it with a suitable cov er .
3. You ma y wish to stain, v arnish or paint the chair. If so, f ollow the instructions
supplied with these coatings.
4. Occasionally wash the chair with a garden hose or pressure sprayer to remove
accumulated dust or dirt. Wipe down or blow off any remaining water left on
the chair after washing.
5. P eriodically (perhaps once per year), recheck the tightness of all fasteners .
Normal usage of the chair and weathering of the wood may cause fasteners to
loosen.
SKU 91090-91091 Page 4
Page 5
Assembly Drawings
SKU 91090-91091 Page 5
Page 6
Parts List
Back Seat Left Front Leg
Right Front Leg Back Support Left Arm
Right Arm Front Support Wood Screws
with Washer and Nut with Washer and Nut
55mm Bolt 65mm Bolt
NOTE: Some parts are listed and shown for illustration purposes only and are not
available individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE
MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY
OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS
TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF
THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THat ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS
OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS
SKU 91090-91091 Page 6
Loading...