Harbor Freight Tools 90849 User Manual

Page 1
ADIRONDACK CHAIR
90849
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our W eb site at http://www.harborfreight.com
Copyright © 2003 by Harbor F reight T ools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight T ools.
For technical questions and replacement parts, please call 1-800-444-3353
Page 2
Specifications
Comfortable natural Fir wood Adirondack chair .
Dimensions:
Overall: 33”L x 36”W x 37”H Back Seat Height: 10” Seat Area:18-1/2”D x 22”W Back Slat Length: 32” Arm Rest: 31-1/4”L x 5-1/8”W Front Legs: 21”L x 3”W x 7/8” Front Seat Height: 15” Side Legs: 35-1/2”L Weight: 18.7 lbs. Weight Capacity: 250 lbs.
Save This Manual
You will need the manual for the saf ety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. K eep your invoice with this man ual. Write the invoice number on the inside of the front cover. Keep the manual and in v oice in a safe and dry place for future reference .
Safety Warnings and Precautions
WARNING: When assembling this item, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before beginning assembly!
1. Keep assembly area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use machines or power tools in damp or wet locations. Keep work area well lighted. Do not use electrically powered tools in the presence of flammable gases or liquids.
3. Keep children away . Children must never be allowed in the assembly area. Do not let them handle machines, tools, or extension cords.
4. Do not exceed weight capacity of this chair. To do so may cause personal injury or property damage.
5. Use the right chair for the job. Do not modify this chair and do not use this chair for a purpose for which it was not intended.
6. Do not overreach. K eep proper footing and balance during assemb ly.
7. Stay alert. Watch what you are doing, use common sense during assembly and use of this chair.
SKU 90849 Page 2
Page 3
8. Use eye and ear protection. Always wear ANSI approved impact safety goggles during assembly . Wear a full f ace shield if y ou are producing wood chips. W ear an ANSI approved dust mask or respirator when working around wood, and chemical dusts and mists.
9. T ake caution as some woods contain preserv atives such as copper chromium arsenate (CCA) which can be toxic. When cutting these materials extra care should be taken to av oid inhalation and minimiz e skin contact.
10. Check for damaged parts. Bef ore using this chair , any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Any part that is damaged should be properly repaired or replaced.
11. Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this item. Approved accessories are available from Harbor F reight T ools.
12. Do not assemble this chair if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not proceed with assembly.
13. Maintenance. F or your saf ety , service and maintenance should be performed regularly . Check the alignment of all parts, and check the tightness of all fasteners.
Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur . It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
Unpacking
When unpacking, check to make sure the following parts are included.
1 Back 1 Front Support 1 Seat 14 Wood Screws 2 Front Legs 10 55mm Bolts with nut and washer 2 Back Supports 2 65mm Bolts with nut and washer 2 Arms 1 Owner’s Manual
If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual, or contact y our local Harbor F reight retailer .
SKU 90849 Page 3
Page 4
Assembly
Carefully unpack the parts and check for damaged or missing parts.
1. Attach Left Front Leg (C1) and Right F ront Leg (C2) to Seat (B) using 3 Bolts (H) per side. Use the included washers and nuts to tighten.
2. Attach both Back Supports (D) to the inner sides of the Seat (B) using 2 Bolts (H) per side. Tighten using the included w ashers and nuts.
3. Attach the Left Arm (E1) and Right Arm (E2) to the Front Legs (C1, C2) using 2 Wood Screws (G) per side . Attach the Arms (E1, E2) to the Back Supports (D) using 1 Long Bolt (I) per side. Tighten the bolts using included washers and nuts .
4. Attach the Back (A) to Seat (B) and Back Supports (D) using a total of 6 Wood Screws (G).
5. Attach the Front Support (F) to the F ront Legs (C1, C2) using 2 W ood Screws (G) per side.
6. Recheck the alignment of all parts, and recheck the tightness of all fasteners.
7. Set up the chair on a flat, level location. Do not exceed load capacity of 250 lbs.
Maintenance
1. This chair is made of natural Fir wood. This beautiful material will naturally weather over time , especially if used outdoors. You can manage the speed and extent of this weathering by controlling the environment in which the chair is used and stored, as well as any coatings you may apply.
2. Leaving the chair outside exposed to w eather , especially direct sun, rain and salt air, will speed the weathering process. This can be slow ed by removing the chair from these conditions, or covering it with a suitable co v er.
3. You may wish to stain, varnish or paint the chair. If so, f ollo w the instructions supplied with these coatings.
4. Occasionally wash the chair with a garden hose or pressure sprayer to remove accumulated dust or dirt. Wipe do wn or blo w off any remaining water left on the chair after washing.
5. P eriodically (perhaps once per year), recheck the tightness of all fasteners . Normal usage of the chair and weathering of the wood may cause fasteners to loosen.
SKU 90849 Page 4
Page 5
Assembly Drawing
SKU 90849 Page 5
Page 6
Parts List
Back Seat Left Front Leg
Right Front Leg Back Support Left Arm
Right Arm Front Support Wood Screws
with Washer and Nut with Washer and Nut
55mm Bolt 65mm Bolt
NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED T O REPLACE ANY PAR TS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THat ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LI­CENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLA­TION OF REPLACEMENT PARTS THERETO.
SKU 90849 Page 6
Loading...